Abstract:Magnesium borate whisker (Mg2B2O5 w) reinforced Mg matrix composite was fabricated by vacuum-gas pressure infiltration process. The Mg2B2O5 w preforms forming process was determined. The Mg2B2O5 whiskers were fabricated into a preform by wet forming method without any binder. The Vacuum-Gas Pressure Infiltration process and parameters are also developed. The micrographs revealed reasonably uniform distribution and random orientation of the whiskers in the as-cast Mg2B2O5 w/AZ91D composite and the composites were without pores defect. The phases were analyzed by XRD patterns for the as-received whiskers, the whiskers sintered at 1 000 degrees C for 3 h and the as-cast composite, respectively. Then, the microstructure evolution of the composite was investigated when the composite was heat-treated. Meanwhile, the relationships between microstructure and micro-hardness of the alloy heat-treated were also studied. The heat-treatment condition were solution at 415 degrees C for 8 and 24 h, respectively, aging treatment at 200 degrees C for 8, 12, 16, 20 and 24 h, respectively and solution at 415 degrees C for 8 or 24 h and subsequent aging treated for 8, 12, 16, 20, 24 h, respectively. The phases were analyzed by XRD patterns for the composites after different heat treated process. The results of XRD patterns were shown to be in good agreement with the microstructures evolution of the composites. The results showed that the micro-hardness of the solution treated composites is decreased due to resolution of eutectic phase, whereas the micro-hardness of the aged composites was increased gradually and the peak hardness is reached to 201 HV in the composite aged for 16 hours. Solution treatment at 415 degrees C for 24 h, the beta-Mg17, Al12 phase is dissolved in the alpha-Mg phase to form oversaturated solid-solution in the composite and then the diffusive beta phase precipitates after subsequent aging treatment at 200 degrees C for 8 h; hence the micro-hardness of the composite was increased 30%. However, as the aging time increased to 24 h, the hardness of the composite was reduced to 183 HV because the beta-Mg17 Al12 phase precipitate changed from continuous fine platelets to discontinuous coarse platelets. It was concluded that the process of solution at 415 degrees C for 24 h and subsequent aging treatment at 200 degrees C for 8 h was the best process for the composite.

Effect of Solution Treatment on the Texture and Tensile Properties of Mg2B2O5w/2024Al Composite

Spectroscopic Characterization and Properties of Mg2B2O5w/AZ91D Magnesium Composites

The Effect of Solution Treatment on the Si Particles’ Morphology Evolution and the Thermal Conductivity and Tensile Properties of Sb-Modified Al-8Si-0.6Mg Alloys

Synthesis and Characterization of Textured Ti2AlC Reinforced Magnesium Composite

Effect of Precipitation Heat Treatment on a Mechanically Alloyed Al‐Based Composite Reinforced with Metallic Glassy Powder

Re -dissolution behavior of secondary phases and mechanical response of CNT/2024Al composites

Effect of solution time on the microstructure, precipitation behavior and mechanical properties of (Co0.5NiFeCrTi0.5 + SiC)p/7075Al hybrid composite

Effect of Heat Treatment on Microstructure and Mechanical Properties of Squeeze Cast n SiCp/AZ91D Magnesium Matrix Composites

Effect of solution heat treatment on the internal architecture and compressive strength of an AlMg4.7Si8 alloy

Effect of Sc Addition and Heat Treatment on the Fracture Behavior of Al-20%Mg2Si Composites: Experiments and Finite Element Simulations

Effect of reinforcement volume fraction and T6 heat treatment on microstructure, thermal and mechanical properties of mesophase pitch-based carbon fiber reinforced aluminum matrix composites

Effect of surface modification of Al2O3 powder with Y2O3 on microstructure and tensile properties of aluninium matrix composites

Effect of aging treatment on the microstructure and mechanical properties of TiO2@CNTs/2024 composite

Effect of ZrMgMo3O12 content on the thermal expansion and dimensional stability of ZrMgMo3O12p/2024Al composites

Microstructure evolution and tensile behavior of MgAlB4w/Al composites at high temperatures

Influence of different extrusion methods on the microstructure, texture evolution and mechanical property of Ti /AZ31 composite

Effects of solution treatment on microstructure and mechanical properties of (SiC+TiB 2 )/Al–Zn–Mg–Cu composite fabricated by laser powder bed fusion

Effect of Solution Treatment on Recrystallization, Texture and Mechanical Properties of 7A65-T74 Aluminum Alloy Super-thick Hot Rolled Plate

Effect of Ti particles on microstructure and mechanical properties of Mg–9Al–1Zn based composite sheets

Effect of Solution Treatment Time on Microstructure Evolution and Properties of Mg-3Y-4Nd-2Al Alloy

Effect of Mg on the microstructure evolution and mechanical properties of 5%TiB2/Al−4.5%Cu composites