Abstract:In some circumstances, hybrid polymer microfluidic chips composed of both elastic, gas-permeable polydimethylsiloxane (PDMS) and rigid plastics are needed. However, it is quite difficult to bond PDMS irreversibly to plastics such as polystyrene (PS). In this article, a facile method for irreversible bonding of PDMS to PS was proposed based on UV/O-3-assisted surface modification in combination of surface silanization. Firstly, a PS sheet was exposed to UV/O-3 to produce oxygen-containing polar moieties, such as hydroxyl and carboxylic acid, on its surface. Secondly, the UV/O-3 treated PS sheet was silanized with (3-aminopropyl)triethoxysilane (APTES) via the reaction between the oxygen-containing polar moieties on the PS surface and the molecules of APTES. Thirdly, the silanized-PS sheet and the PDMS substrate with micro channel network were treated with UV/O-3 again to generate silanol moieties on both surfaces. Finally, the UV/O-3 treated PDMS was immediately brought intimate contact with the UV/O-3 treated silanized-PS, and irreversible bonding of PDMS with PS occurred after putting the PDMS-PS complex at room temperature for 1 h through the condensation reaction between silanol moieties. Contact angle measurement, X-ray photoelectron spectroscopy, total reflection Fourier transformation infrared spectrometer were applied to characterize the surface chemistry of the PS during the UV/O-3 treatment and silanization. The hybrid PDMS-PS microfludic chips prepared with the established method can bear a gas pressure higher than 0.5 MPa and a water stream at a flow rate higher than 170 mu L/min (the test channels were 2.5 cm in the length, 50 mu m in the width, 200 mu m in the depth). A hybrid PDMS-PS microfluidic chip composed of gas-permeable PDMS substrate with channel network and excellently biocompatible PS cover sheet was fabricated for cell culture. The experimental results showed that HeLa cells cultured in the hybrid PDMS-PS microchip grew much better than those cultured in the full PS microchip, and slightly better than those in the full PDMS microchip.

Fabrication of the Micromachined Poly-Dimethylsiloxane Pyramidal Tips Arrays for Biotechnology Packaging Applications

POLYMER-DERIVED SIC CERAMIC WITH TRIPLY PERIOD MINIMAL SURFACE STRUCTURE FABRICATION THROUGH DIGITAL LIGHT PROCESSING

Patterned Microstructure Array Fabrication By Using A Novel Standing Surface Acoustic Wave Device

Fabrication and surface treatment of silicon mold for polymer microarray

Novel polydimethylsiloxane (PDMS) based microchannel fabrication method for lab-on-a-chip application

Microfabrication of 3D-Polymeric Structures Using Soft Lithography for Tissue Engineering

Fabrication of polydimethylsiloxane nanofluidic chips under AFM tip-based nanomilling process

An Approach for Irreversible Bonding of PDMS-PS Hybrid Microfluidic Chips at Room Temperature

Fabrication of Polymethyl Methacrylate (PMMA) Hydrophilic Surfaces Using Combined Offset-Tool-Servo Flycutting and Hot Embossing Methods

Fabrication of cantilever arrays with nano-aperture hollow tips for parallel microplasma etching

Fabrication of Nano-Aperture Hollow Tip Array for Microplasma Etching

Site-controlled Fabrication of Silicon Nanotips by Indentation-Induced Selective Etching

Fabrication of Microwell Arrays Based on Two-Dimensional Ordered Polystyrene Microspheres for High-Throughput Single-Cell Analysis.

Poly(dimethylsiloxane) Microchips with Two Sharpened Stretching Tips and Its Application to Protein Separation Using Dynamic Coating

Surface Modification of Poly(dimethylsiloxane) and Its Applications in Microfluidics-Based Biological Analysis

A new process for fabricating tip-shaped polymer microstructure array with patterned metallic coatings

Polymer Microchannel and Micromold Surface Polishing for Rapid, Low-Quantity Polydimethylsiloxane and Thermoplastic Microfluidic Device Fabrication

Fabrication of a polymer micro needle array by mask-dragging X-ray lithography and alignment X-ray lithography

Rapid prototyping of PDMS microdevices via <i></i>PLAT on nonplanar surfaces with flexible hollow-out mask

Microfabrication of Micropore Array for Cell Separation and Cell Assay.

A simple method for fabricating multi-layer PDMS structures for 3D microfluidic chips