Decomposition Behavior of Ammonium Nitrate on Ceria Catalysts and Its Role in the Nh3-Scr Reaction

Ze Chen,Zhichun Si,Li Cao,Xiaodong Wu,Rui Ran,Duan Weng

DOI: https://doi.org/10.1039/c7cy00509a

IF: 6.177

2017-01-01

Catalysis Science & Technology

Abstract:Ceria catalyst's redox properties promote NH4NO3 decomposition while acidity inhibits this process.

What problem does this paper attempt to address?

Synergistic Effect Between Ceria and Tungsten Oxide on WO3–CeO2–TiO2 Catalysts for NH3-SCR Reaction

Lei Chen,Duan Weng,Zhichun Si,Xiaodong Wu

DOI: https://doi.org/10.1016/j.pnsc.2012.07.004

2012-01-01

Abstract:WO3–CeO2–TiO2 catalysts for NO (nitrogen monoxide) reduction by ammonia were prepared by a sol–gel method. The catalysts were characterized by BET, XRD, Raman, NH3/NO adsorption and H2-TPR to investigate the relationships among the catalyst composition, structure, redox property, acidity and deNOx activity. WO3–CeO2–TiO2 catalysts show a high activity in a broad temperature range of 200–480°C. The low-temperature activity of catalysts is sensitive to the catalyst composition especially under low-O2-content atmospheres. It may be related to the synergistic effect between CeOx and WOx in the catalysts. On one hand, the interaction between ceria and tungsten oxide promotes the activation of gaseous oxygen to compensate the lattice oxygen consumed in NH3-SCR (selective catalytic reduction) reaction at low temperatures. Meanwhile, the Brønsted acid sites mainly arise from tungsten oxides, Lewis acid sites mainly arise from ceria. Both of the Brønsted and Lewis acid sites facilitate the adsorption of NH3 on catalysts and improve the stability of the adsorbed ammonia species, which are beneficial to the NH3-SCR reaction.
Ceria Supported on Sulfated Zirconia As A Superacid Catalyst for Selective Catalytic Reduction of No with Nh3

Shan Gao,Xiongbo Chen,Haiqiang Wang,Jiansong Mo,Zhongbiao Wu,Yue Liu,Xiaole Weng

DOI: https://doi.org/10.1016/j.jcis.2012.12.034

IF: 9.9

2013-01-01

Journal of Colloid and Interface Science

Abstract:In this paper, ceria supported on sulfated zirconia (CeSZ) as a superacid catalyst was synthesized and the resulted performances for selective catalytic reduction (SCR) of NO with NH(3) were investigated. Experimental results revealed that the sulfation of zirconia supports could greatly improve the SCR activity of the catalysts. Among the tested samples, the CeSZ catalyst with Ce/Zr mole ratio at 0.095 possessed the highest NO conversion (i.e., 98.6% at ca. 420 °C and 180,000 h(-1)). The sulfation had led to a formation of pure tetragonal phase of ZrO(2), a well dispersion of CeO(2), abundant stable superacid sites, increasing surface area and enrichment of Ce(3+) on the surface, all of which were responsible for its excellent performance in SCR of NO with NH(3).
Bimetallic Cerium–copper Nanoparticles Embedded in Ordered Mesoporous Carbons As Effective Catalysts for the Selective Catalytic Reduction of NO with NH3

Jinghuan Chen,Feifei Cao,Ruiyang Qu,Xiang Gao,Kefa Cen

DOI: https://doi.org/10.1016/j.jcis.2015.06.001

IF: 9.9

2015-01-01

Journal of Colloid and Interface Science

Abstract:Bimetallic cerium-copper nanoparticles embedded in ordered mesoporous carbons (OMCs) with various Ce/Cu ratios were synthesized by "one-pot" self-assembly method, and their activities for the selective catalytic reduction (SCR) of NO with ammonia were studied. The structural and textural properties, surface chemistry, acidity, and reducibility were investigated by various techniques. Results showed that NO conversion was greatly influenced by the weight ratio of Ce to Cu. An appropriate Ce/Cu ratio in OMCs could enhance catalytic performance; the optimal catalytic performance was obtained with Ce5Cu5-OMC. Ordered mesoporous structures were formed for all synthesized samples. When Ce or Cu was incorporated into the OMCs, the amount of surface acidic oxygen functional groups increased, thereby promoting the acidic properties of the OMCs, especially those of the Cu-rich OMCs. The surface Cu(2+) species may accelerate ammonia activation and may play an important role in SCR reaction. The temperature-programmed reduction results illustrated that the Cu-rich OMCs had better reducibility, and the appropriate Ce/Cu ratio could further enhance the redox ability of the CexCuy-OMC catalysts. The existing redox cycle (Ce(4+)+Cu(+)↔Cu(2+)+Ce(3+)) promoted the activation of NH3 and consequently improved NH3-SCR activity.
Activating low-temperature NH3-SCR catalyst by breaking the strong interface between acid and redox sites: A case of model Ce2(SO4)3-CeO2 study

Jiawei Ji,Meizan Jing,Xiuwen Wang,Wei Tan,Kai Guo,Lulu Li,Xin Wang,Wang Song,Lijun Cheng,Jingfang Sun,Weiyu Song,Changjin Tang,Jian Liu,Lin Dong

DOI: https://doi.org/10.1016/j.jcat.2021.05.001

IF: 7.3

2021-07-01

Journal of Catalysis

Abstract:The occurrence of NH3-SCR (selective catalytic reduction of NO with NH3) reaction on catalyst surface typically requires acid and redox sites. However, the role of acid-redox interaction on NH3-SCR performance is still obscure due to complex acidities and entangled acid-redox sites. Herein, three types of model Ce2(SO4)3-CeO2 catalysts with distinct interfaces are constructed to reveal the effect of acid-redox interaction on NH3-SCR performance. That is, SO4 2-/CeO2-VS (vapor sulfation of ceria) with strong acid-redox interfacial contact, SO4 2-/CeO2-WI (wet impregnation), and SO4 2-/CeO2-SG (solid grinding) with limited interfaces. It is found the redox property is significantly disturbed as a result of the electron-withdrawing effect from the sulfate. Theoretical result unravels that the introduction of Ce2(SO4)3 retards the oxygen vacancy formation over CeO2. Due to restricted interfaces in SO4 2-/CeO2-SG, the negative influence from acid sites is greatly alleviated. Further mechanism study discloses the weakened acid-redox interaction actually changes the nature of surface NOx species, resulting in the generation of reactive species (*O-N-O* and cis-N2O2 2-) and the promotion of surface reaction via Langmuir-Hinshelwood (L-H) mechanism.

chemistry, physical,engineering, chemical
Structure–Activity Relationship of Titanate Nanotube-Confined Ceria Catalysts in Selective Catalytic Reduction of NO with Ammonia

Haiqiang Wang,Shuang Cao,Chaoping Cen,Xiongbo Chen,Zhongbiao Wu

DOI: https://doi.org/10.1007/s10562-013-1084-5

IF: 2.936

2013-01-01

Catalysis Letters

Abstract:A series of titanate nanotube-confined ceria catalysts with different Ce/Ti molar ratios were synthesized. The structure of ceria transformed in the following order: amorphous → small crystals → middle crystals → large crystals. Compared with ceria crystals, amorphous ceria with large quantities of surface defects showed better deNO x activity. Graphical Abstract
Ce0.6Zr0.3Y0.1O2 solid solutions-supported Ni Co bimetal nanocatalysts for NH3 decomposition

Chuanqing Huang,Huaxi Li,Jinmei Yang,Changqing Wang,Feiyang Hu,Xuewen Wang,Zhang-Hui Lu,Gang Feng,Rongbin Zhang

DOI: https://doi.org/10.1016/j.apsusc.2019.01.269

IF: 6.7

2019-06-01

Applied Surface Science

Abstract:Ammonia has become an attractive source for COx-free hydrogen production for fuel cell applications. The catalytic performance of Ce0.6Zr0.3Y0.1O2 solid solutions supported Ni, Co and NiCo bimetallic catalysts are evaluated in the temperature range of 300–600 °C at atmospheric pressure. Due to the synergistic effect between Ni and Co, CZY supported NiCo bimetallic catalysts show higher ammonia decomposition activity compared to Ni or Co monometallic samples. The NiCo bimetallic catalyst with the Ni/Co mass ratio of 1/9 exhibits the highest NH3 conversion with the GHSV of 6000 mL h−1 gcat −1, which reaches 100% conversion at 600 °C. Moreover, the Ni1Co9/CZY catalyst shows good thermal stability during the 72 h reaction time. The Ni1Co9/CZY have the highest total H2-uptake of 0.35 mmol‧g−1 and the highest TOFH2 value (40.57 min−1) at 350 °C among all the catalysts. Our characterization confirms the formation of NiCo alloy is responsible for the high activity of Ni1Co9/CZY catalyst for the ammonia decomposition.

chemistry, physical,physics, applied, condensed matter,materials science, coatings & films
Thermal Decomposition Mechanism of Ammonium Nitrate on the Main Crystal Surface of Ferric Oxide: Experimental and Theoretical Studies

Qiangqiang Lu,Yiwen Hu,Junqing Yang,Hongyu Yang,Lei Xiao,Fengqi Zhao,Hongxu Gao,Wei Jiang,Gazi Hao

DOI: https://doi.org/10.1021/acs.langmuir.3c03230

IF: 3.9

2024-01-30

Langmuir

Abstract:Understanding the decomposition process of ammonium nitrate (AN) on catalyst surfaces is crucial for the development of practical and efficient catalysts in AN-based propellants. In this study, two types of nano-Fe2O3 catalysts were synthesized: spherical particles with high-exposure (104) facets and flaky particles with high-exposure (110) facets. Through thermal analysis and particle size analysis, it was found that the nanosheet-Fe2O3 catalyst achieved more complete AN decomposition despite having a larger average particle size compared to nanosphere-Fe2O3. Subsequently, the effects of AN pyrolysis on the (110) and (104) facets were investigated by theoretical simulations. Through studying the interaction between AN and crystal facets, it was determined that the electron transfer efficiency on the (110) facet is stronger compared to that on the (104) facet. Additionally, the free-energy step diagrams for the reaction of the AN molecule on the two facets were calculated with the DFT + U method. Comparative analysis led us to conclude that the (110) facet of α-Fe2O3 is more favorable for AN pyrolysis compared to the (104) facet. Our study seeks to deepen the understanding of the mechanism underlying AN pyrolysis and present new ideas for the development of effective catalysts in AN pyrolysis.
Unraveling the Complete Mechanism of the NH3-Selective Catalytic Reduction of NO over CeO2

Weibin Chen,Shenzhen Xu

DOI: https://doi.org/10.1021/acscatal.3c04490

IF: 12.9

2023-01-01

ACS Catalysis

Abstract:CeO2-based oxides, with promising redox properties, exhibit application potential for the selective catalytic reduction (SCR) of nitrogen oxide (NOx) with NH3 (NH3-SCR). Despite decades of research, the underlying mechanisms governing the SCR activity remain unclear, and the catalytic paths of fast SCR (Fast_SCR) and standard SCR (Std_SCR) on the CeO2 surfaces are still under debate. Understanding the complete SCR reaction mechanism is crucial for the design and synthesis of efficient SCR catalysts. We perform density functional theory (DFT) simulations, synthesize CeO2 model catalysts for in situ spectroscopy experiments (in situ drifts, in situ Raman, in situ NAP-XPS, and in situ EPR) and SCR activity evaluation experiments to reveal the complete mechanism for NH3-SCR over CeO2. We find that the Std_SCR and the fast-SCR mechanisms share the same NO reduction path but go through two different adsorbed-hydrogen (H*) removal processes. For the NO reduction reaction, NH3 dissociation to NH2* and H* is catalyzed by the coupled [O* + O-vac] species. The NH2* then combines with NO to generate the NH2NO active intermediate, which further dissociates to N-2 and H2O. In the Fast_SCR H* removal process, NO2 reacts with H* and *NH3 to generate H2O and NH2NO. For the Std_SCR, the catalytic species of O* is consumed to complete the H* removal. Our experimental-theoretical joint study further provides design principles of oxide catalysts for NO removal based on the atomic-level understanding of the catalytic mechanisms.
NH3-SCR reaction mechanisms of NbOx/Ce0.75Zr0.25O2 catalyst: DRIFTS and kinetics studies

Ma Ziran,Wu Xiaodong,Harelind Hanna,Weng Duan,Wang Baodong,Si Zhichun

DOI: https://doi.org/10.1016/j.molcata.2016.06.023

2016-01-01

Abstract:•NbOx/Ce0.75Zr0.25O2 catalyst shows high NH3-SCR activity in a broad temperature window.•Reaction mechanisms on NbCZ catalyst are verified by DRIFTS and kinetic studies.•“L-H” and “E-R” mechanisms are presented for NbCZ in different temperature ranges.•The NH4NO3+NO reaction is accelerated over NbCZ catalyst at low temperatures.•The NH2+NO reaction is also promoted by addition of niobia at high temperatures.
New Insights into the Promotional Mechanism of Ceria for Activity and Ammonium Bisulfate Resistance over V/WTi Catalyst for Selective Catalytic Reduction of NO with NH3

Chenxu Li

DOI: https://doi.org/10.1016/j.apcata.2018.05.005

IF: 5.723

2018-01-01

Applied Catalysis A General

Abstract:The promotion of Ce-doped V/WTi for NH3-SCR performance and ammonium bisulfate (ABS) resistance is fully illustrated. The V2O5/CeO2/WTi-2 presents an excellent NOx conversion at 280 degrees C in the presence of 1000 ppm SO2. The introduction of ceria contributes to the vanadia species agglomeration into the oligomeric V-O-V structures and tight connects with the adjacent vanadium species to form the redox structure of Ce4+-O-Ce3+-O-V5+-O-V5+-O-Ce3+-O-Ce4+, which facilitates the electronic conduction between ceria and vanadia species. The electronic interaction via the redox structure promotes the activation of ammonia adsorbed on vanadia and nitrate species on ceria, which lowers the apparent activation energies (Ea) and significantly improves the NOx conversion rate. The addition of ceria protects active V sites poisoning and improves the stability of the adsorbed NOx species, which prevents VOSO4 formation and competitively inhibits the adsorption of SO2 with less metal sulfate formation on ceria. In addition, the electrons donating from vanadia to ceria species via the redox structure could make ceria species existing in electron enrichment state and boost the electrons around ceria deviating towards sulfates and strengthen the bonding between ceria and as-formed ABS species, which weakens the stability of ABS and promotes to initiate NH3-SCR reaction between the NH4+ species of ABS and NO + O-2. The faster NH3-SCR conversion rate promoted by the redox structure further suppresses the competitive reaction between sulfate and ammonia species, which results in no ABS formation over V/Ce/WTi-2.
Role of cation in catalytic decomposition of ammonia over Ni supported zeolite Y catalysts

Shaofeng Gong,Zexue Du,Yi Hu,Wenwu Yao

DOI: https://doi.org/10.1016/j.ijhydene.2024.03.204

IF: 7.2

2024-03-24

International Journal of Hydrogen Energy

Abstract:A series of nickel (Ni) catalysts were prepared using zeolites Y with different cation types (Na, Mg, Ca, Sr, Ba, Ce, and La) as supports and characterized by using XRD, BET, ICP-OES, XPS, and TEM , as well as NH 3 -TPD, CO 2 -TPD, and H 2 -TPR techniques. Their catalytic performances in decomposition of ammonia (NH 3 ) to hydrogen (H 2 ) were evaluated with a fixed-bed flow reactor system. The catalytic activities of the prepared catalysts for NH 3 decomposition decreased in the order of Ni/SrY > Ni/BaY > Ni/LaY > Ni/CaY > Ni/NaY > Ni/MgY > Ni/CeY. The high activity of Ni/SrY catalyst may be attributed to its small Ni nanoparticle size, high basicity and strong interaction between highly dispersed Ni nanoparticles and SrY support. At 600 °C and GHSV of 9000 mLNH 3 ·g cat −1 ·h −1 , 98.0 % NH 3 conversion with about 105.2 mmol min −1 ·g Ni −1 H 2 formation rate can be accomplished over Ni/SrY catalyst.

energy & fuels,electrochemistry,chemistry, physical
Promotional effect of nitrogen-doping on a ceria unary oxide catalyst with rich oxygen vacancies for selective catalytic reduction of NO with NH3

Qiliang Cong,Liang Chen,Xiaoxiang Wang,Heyao Ma,Jingkai Zhao,Sujing Li,Yang Hou,Wei Li

DOI: https://doi.org/10.1016/j.cej.2019.122302

IF: 15.1

2020-01-01

Chemical Engineering Journal

Abstract:•The N-doped ceria catalyst was prepared by NH3-annealing method.•Oxygen vacancies, Brønsted acid sites and active nitrites were enriched after nitrogen-doping.•Inhibition of NH3 oxidation promoted the SCR activity of the N-doped ceria.
Hexavalent Metal Cations Doped into Ceria Inducing the Formation of Binuclear Sites Ce3+–O–Ce3+ to Boost the NH3-SCR Reaction

Shan Yang,Xiaoyue Zhu,Shurui Chen,Xuechen Zhu,Hao Liu,Jianjun Chen,Dezhan Chen,Chuanzhi Sun,Junhua Li

DOI: https://doi.org/10.1021/acscatal.4c00043

IF: 12.9

2024-01-01

ACS Catalysis

Abstract:The application of selective catalytic reduction with ammonia (NH3-SCR) technology urgently requires catalysts with good performance to control nitrogen oxide (NOx, x = 1, 2) emissions, and structural analysis of such catalysts is necessary and crucial to elucidate the performance of catalytically active sites. Thus, we prepared molybdenum (Mo)-doped CeO2 catalysts to achieve a substantial leap in catalytic performance. The results revealed that the emergence of Ce3+-O-Ce3+ structural units induced by Mo doping achieved the low-energy barrier activation of the NH3 molecule, which transformed the dominant reaction mechanism in the catalytic reaction and thus led to a much better SCR performance. Furthermore, we designed tungsten (W)-doped CeO2 catalysts with the same doping amount as Mo and found that the catalysts exhibited almost the same activity trend as the Mo-doped CeO2 catalysts, which further confirmed the pivotal role of the Ce3+-O-Ce3+ structural units. This study provides a basic theoretical foundation for the design of ceria-based SCR catalysts with efficient catalytic performance for NOx removal.
In-situ Formation of Carbon-Doped Cerium-Zirconium Solid Solution As a Superacid Catalyst for the Removal of NOx

Ruihua Wang,Zhifei Hao,Xu Huang,Yue Peng,Guoquan Liu,Yuguo Xia,Sihui Zhan

DOI: https://doi.org/10.1016/j.apcatb.2023.123098

2023-01-01

Abstract:Defects engineering in nanomaterials can be used to precisely and effectively modulate catalysts’ reactivity. Here we report a highly efficient NH3-SCR catalyst constructed with in-situ formation of carbon-doped CeZrO2−x with dual defects, in which O atoms are substituted by C atoms to generate surface oxygen vacancies and subsurface oxygen substitutions. The carbon-doped CeZrO2−x exhibit superior activity and better SO2/H2O resistance compared with traditional bulk CeZrOx and V2O5-WO3/TiO2. The related characterization results reveal that the surface oxygen vacancy and subsurface oxygen substitution resulted in the formation of a large number of unsaturated coordination Ce and Zr species on catalyst’s surface, which contributed to the adsorption and activation of NH3, thus promoting the catalytic activity. Meanwhile, the abundant oxygen vacancy also stimulated the E-R reaction pathway over carbon-doped CeZrO2−x. In addition, it was proved that more zirconium sulfate and unstable ammonium sulfate species were exposed over carbon-doped CeZrO2−x, benifiting the better SO2-tolerance.
Protection Effect of Ammonia on CeNbTi NH3-SCR Catalyst from SO2 Poisoning

Yang Gao,Li Cao,Xiaodong Wu,Xu Zhang,Ziran Ma,Rui Ran,Zhichun Si,Duan Weng,Baodong Wang

DOI: https://doi.org/10.3390/catal12111430

IF: 3.9

2022-11-15

Catalysts

Abstract:CeNbTi catalyst was poisoned in different sulfur poisoning atmospheres at 300 °C for 6 h and then was evaluated for selective catalytic reduction (SCR) of NOx with NH3. The catalyst deactivation upon SO2 exposure was effectively inhibited in the presence of NH3. Temperature-programmed decomposition (TPD) analyses were applied to identify deposit species on the poisoned catalysts by comparison with several groups of reference samples. Diffuses reflectance infrared Fourier transform spectroscopy (DRIFTS) over CeNbTi catalysts with different poisoning pretreatments and gas purging sequences were designed to investigate the roles of NH3 in the removal of surface sulfites and sulfates. More ammonium sulfates including ammonium bisulfate and ammonium cerium sulfate were generated instead of inert cerium sulfate in these conditions. The mechanisms about the formation and transformation of surface deposits upon sulfur poisoning w/wo NH3 were explored, which provided a basis for developing Ce-based mixed oxides as SCR catalysts for stationary sources.

chemistry, physical
The Enhanced Performance of Ceria with Surface Sulfation for Selective Catalytic Reduction of No by Nh3

Tingting Gu,Yue Liu,Xiaole Weng,Haiqiang Wang,Zhongbiao Wu

DOI: https://doi.org/10.1016/j.catcom.2010.10.003

IF: 3.51

2010-01-01

Catalysis Communications

Abstract:The selective catalytic reduction (SCR) of NO with NH3 over fresh and sulfated CeO2 catalysts had been investigated in this study. Experimental results showed that the sulfated CeO2 sample had significantly higher NO conversion than the fresh one and revealed an excellent selectivity to N2 within the temperature range of 200–570°C. By characterizations via BET, XRD, XPS, EDS and TPD, it was concluded that the improvement in SCR activity by sulfation might be originated from the increase of active oxygen species and the enhancement of NH3 chemisorption after surface sulfation, both of which were conducive to NH3 activation.
Effect of Ceria Precursor on the Physicochemical and Catalytic Properties of Mn–W/CeO2 Nanocatalysts for NH3 SCR at Low Temperature

Xiuyun Wang,Kai Zhang,Weitao Zhao,Yangyu Zhang,Zhixin Lang,Tianhua Zhang,Yihong Xiao,Yongfan Zhang,Huazhen Chang,Lilong Jiang

DOI: https://doi.org/10.1021/acs.iecr.7b03466

2017-01-01

Industrial & Engineering Chemistry Research

Abstract:A series of Mn-W/CeO2 catalysts were synthesized by employing Ce-NO-R nanorods [Ce(NO3)(3). 6H(2)O as the precursor] and Ce-Cl-C nanocubes and Ce-Cl-R nanorods (CeCl3 center dot 7H(2)O as the precursor) as the supports, and their structures and catalytic performances in NOx removal were investigated. TEM results demonstrate that the morphology of the CeO2 species is associated with the Ce precursor. The activity results show that the NOu conversion in Mn-W/Ce-NO-R is greater than 96% at 150 degrees C, which is much higher than those in Mn-W/Ce-Cl-R and Mn-W/Ce-Cl-C. At the same time, Mn-W/Ce-NO-R exhibits strong SO2 tolerance and excellent H2O resistance. DFT modeling shows that NO adsorbs over Mn-W/Ce-NO-R{110} by forming ONO*, whereas NO prefers to adsorb on the 0 vacancies in Mn-W/Ce-Cl-C{100}. Moreover, the superior catalytic performance of Mn-W/Ce-NO-R is associated with its greater amounts of surface Ce3+ and Mn4+ species, surface acid sites, and active oxygen species, resulting in the promotion of the reactions according to the Langmuir-Hinshelwood and Eley-Rideal mechanisms.
Deterioration mechanism of selective catalytic oxidation of NH3 to N2 over CeZrO4 by incorporation of alkali metals and calcium

Zhong Wang,Shuangju Li,Da Wang,Bingbing Wang,Li Xu,Dan Chen,Xuebing Li

DOI: https://doi.org/10.1016/j.surfin.2022.101971

IF: 6.2

2022-06-01

Surfaces and Interfaces

Abstract:Alkali metals and calcium were added to CeZrO4 mixed oxide by wet impregnation. The CeZrO4 catalyst poisoned by alkali metals and calcium could inhibit the SCO performance. In particular, Na poisoned catalyst showed the lowest NH3 conversion. The structure analysis proved that this poisoning of metal ions could weaken the interaction between cerium and zirconium, particularly K and Na ions. Moreover, the low surface Brønsted acidity might directly reduce the NH3 oxidation performance. The reaction pathway by in situ DRIFTS results at low temperatures (<350 °C) over poisoned catalyst was different from the temperatures above 350 °C, which was followed the -NH and i-SCR mechanism, respectively.

chemistry, physical,physics, applied, condensed matter,materials science, coatings & films
Temperature-Dependent Influencing Mechanism of Carbon Monoxide on the NH<sub>3</sub>-SCR Process over Ceria-Based Catalysts

Xiaoqiang Wang,Yue Liu,Zhongbiao Wu

DOI: https://doi.org/10.1021/acsestengg.1c00090

IF: 7.1

2021-01-01

ACS ES&T Engineering

Abstract:Ceria-based catalysts have been investigated extensively for their good activities at low-medium temperatures for selective catalytic reduction of NO with ammonia (NH3-SCR). In considering the usual coexistence of carbon monoxide with nitrogen oxides, the effects of CO on SCR performance over the Sb0.5CeZr2Ox SCR catalyst have been investigated in this work, and a temperature-dependent CO influencing mechanism was disclosed. The presence of CO would somewhat decrease the SCR activity, where such a deteriorating effect became more serious in the high-temperature range. For instance, NOx conversion was suppressed from about 91% to 67% at ca. 380 degrees C in the presence of 1% CO. Primarily, the presence of CO would inhibit the chemical adsorption of NO and the formation of reactive nitrate species, which was the main factor of the decreased SCR activity in the low-medium temperature range. Importantly, at higher temperatures, the adsorbed -NHx species would be partly consumed by excessive CO to generate -NCO species, thus disturbing the reduction process of NO. The generated -NCO species were also readily oxidized to release undesired NOx. The findings could provide guidelines for practical applications of ceria-based SCR catalysts.
Ammonia partial cracking over low-cost Ni catalysts for enhancing combustion

Mingyu Yu,Ruize Sun,Guangqian Luo,Li Wang,Xian Li,Hong Yao

DOI: https://doi.org/10.1016/j.fuel.2024.131306

IF: 7.4

2024-03-13

Fuel

Abstract:Partial cracking is a feasible strategy to improve ammonia (NH 3 ) combustion. The nickel (Ni) based catalysts have become promising non-noble metal NH 3 decomposition catalysts owing to the low cost and decent performance. In order to meet the demand of reducing cost and expanding production, a batch of Ni catalysts were obtained by using low-cost supports and traditional impregnation preparation method. It was found that the Al 2 O 3 was the optimal support for Ni catalysts by comparing the catalytic performance. On the basis of Ni/Al 2 O 3 catalysts, the catalytic activity was further improved by introducing cerium (Ce) modification. The catalytic performance of Ce-doped catalysts enhanced at first and then decreased with the rise of Ce contents. Among all of catalysts in this work, the Ni/Al 0.5 Ce 0.5 O x catalysts possessed the highest activity and the lowest apparent activation energy. The characterization results suggested that the addition of Ce could destroy the pore structure of Al 2 O 3 supports, but it might promote the formation of more B5 active sites. The NH 3 temperature programmed desorption (NH 3 -TPD) results implied that the introduction of Ce strengthened the strong interactions between meatal and support, which improved the activity and stability of the Ce-doped catalysts. The Ni/Al 0.5 Ce 0.5 O x catalysts were proved to possess excellent resistance to the high temperature sintering through the 32 h's thermal stability test. This study provides a feasible path for preparing low-cost Ni catalysts for NH 3 decomposition.

energy & fuels,engineering, chemical

Decomposition Behavior of Ammonium Nitrate on Ceria Catalysts and Its Role in the Nh3-Scr Reaction

Synergistic Effect Between Ceria and Tungsten Oxide on WO3–CeO2–TiO2 Catalysts for NH3-SCR Reaction

Ceria Supported on Sulfated Zirconia As A Superacid Catalyst for Selective Catalytic Reduction of No with Nh3

Bimetallic Cerium–copper Nanoparticles Embedded in Ordered Mesoporous Carbons As Effective Catalysts for the Selective Catalytic Reduction of NO with NH3

Activating low-temperature NH3-SCR catalyst by breaking the strong interface between acid and redox sites: A case of model Ce2(SO4)3-CeO2 study

Structure–Activity Relationship of Titanate Nanotube-Confined Ceria Catalysts in Selective Catalytic Reduction of NO with Ammonia

Ce0.6Zr0.3Y0.1O2 solid solutions-supported Ni Co bimetal nanocatalysts for NH3 decomposition

Thermal Decomposition Mechanism of Ammonium Nitrate on the Main Crystal Surface of Ferric Oxide: Experimental and Theoretical Studies

Unraveling the Complete Mechanism of the NH3-Selective Catalytic Reduction of NO over CeO2

NH3-SCR reaction mechanisms of NbOx/Ce0.75Zr0.25O2 catalyst: DRIFTS and kinetics studies

New Insights into the Promotional Mechanism of Ceria for Activity and Ammonium Bisulfate Resistance over V/WTi Catalyst for Selective Catalytic Reduction of NO with NH3

Role of cation in catalytic decomposition of ammonia over Ni supported zeolite Y catalysts

Promotional effect of nitrogen-doping on a ceria unary oxide catalyst with rich oxygen vacancies for selective catalytic reduction of NO with NH3

Hexavalent Metal Cations Doped into Ceria Inducing the Formation of Binuclear Sites Ce3+–O–Ce3+ to Boost the NH3-SCR Reaction

In-situ Formation of Carbon-Doped Cerium-Zirconium Solid Solution As a Superacid Catalyst for the Removal of NOx

Protection Effect of Ammonia on CeNbTi NH3-SCR Catalyst from SO2 Poisoning

The Enhanced Performance of Ceria with Surface Sulfation for Selective Catalytic Reduction of No by Nh3

Effect of Ceria Precursor on the Physicochemical and Catalytic Properties of Mn–W/CeO2 Nanocatalysts for NH3 SCR at Low Temperature

Deterioration mechanism of selective catalytic oxidation of NH3 to N2 over CeZrO4 by incorporation of alkali metals and calcium

Temperature-Dependent Influencing Mechanism of Carbon Monoxide on the NH<sub>3</sub>-SCR Process over Ceria-Based Catalysts

Ammonia partial cracking over low-cost Ni catalysts for enhancing combustion