Abstract:Intergranular corrosion trigged by sensitization is the main reason for the failure of Al-Mg alloys with a Mg content > 3 wt%. The early stage of corrosion occurs at the grain boundaries (GBs) and controls the evolution of the Al-Mg alloy's degradation. However, corrosion initiation and the oxide film formation on GBs before and after sensitization need to be further explored. Here, the early stages of GB corrosion of the 5083 Al-Mg alloy, before and after sensitization, are investigated using quasi in-situ and focused ion beam microscopy and transmission electron microscopy (FIB-TEM). Sensitization caused a decrease in the corrosion resistance of the Al-Mg alloy due to the precipitation of Al-Mg phase on GBs. On the GBs of both unsensitized and sensitized Al-Mg alloys, the oxide film penetrated deeply into the alloy matrix compared with the neighboring grains. Mg segregation on the GB of the sensitized Al-Mg alloy led to the formation of a thick, Mg-enriched, oxide film on the GB surface. Density-functional theory (DFT) calculations suggest that the local electron accumulation at the interface of the oxide and the sub-surface Al atoms provided possible sites for O adsorption. The GB showed a stronger tendency for oxidation than neighboring grains in terms of its structural and electronic properties, and Mg doping enhanced the tendency of O adsorption and electron localization on the GB. This led to the formation of a less protective Mg-enriched oxide film on Mg-segregated GBs. Our findings advance the mechanistic understanding of near atomic-scale corrosion on the GBs of Al-Mg alloys.

Near-atomic-scale study of the oxide films on the grain boundaries of Al-Mg alloys at the initial stage of corrosion: Experimental investigations and DFT calculations

Improve Sensitization and Corrosion Resistance of an Al-Mg Alloy by Optimization of Grain Boundaries

Initial localized corrosion induced by multiscale precipitates in the new generation high-strength Al-Zn-Mg-Cu alloy

Phase-field investigation of intergranular corrosion mechanism and kinetics in aluminum alloys

In-situ AFM and quasi-in-situ studies for localized corrosion in Mg-9Al-1Fe-(Gd) alloys under 3.5 wt.% NaCl environment

Role of intermetallic phases in initiation and propagation of intergranular corrosion of an Al-Li-Cu-Mg alloy

Stress Corrosion Cracking Resistant Nanostructured Al-Mg Alloy with Low Angle Grain Boundaries

Origin of the Zn-Induced Al Intergranular Corrosion of the Outermost Surface Layer of the Aluminium Grain Boundary: an Ab Initio Study

How solute atoms control aqueous corrosion of Al-alloys

First-principles investigation of the Mg, Cu segregation at Al Σ5 (310) and Σ9 (221) symmetrical tilt grain boundaries

Direct Observation of Atomic-Scale Origins of Local Dissolution in Al-Cu-Mg Alloys

Multi-scale study on the electrochemical behavior and corrosion mechanism of 5083 aluminum alloy with different microstructures in a NaCl environment

Influence of β-Mg 17 Al 12 and Al-Mn intermetallic compounds on the corrosion behaviour of cast and solution treated Mg-Al-Zn-Mn alloys

Formation of amorphous precipitates in a corroded over-aged Al-Mg-Si alloy

On the localized corrosion of AA5083 in a simulated dynamic seawater/air interface—Part 3: effects of sensitization

Effect of grain size uniformity and crystallographic orientation on the corrosion behavior of Mg-2Zn-1Al bar

Correlations Between Stress Corrosion Cracking Susceptibility and Grain Boundary Microstructures for an Al–Zn–Mg Alloy

Influence of Grain Structure on Quench Sensitivity Relative to Localized Corrosion of High Strength Aluminum Alloy

Engineering Atomic-to-Nano Scale Structural Homogeneity towards High Corrosion Resistance of Amorphous Magnesium-Based Alloys

Elucidating the dependence of corrosion behavior and mechanical property on the grain structure of low-temperature as-extruded Mg–Zn–Ca–Zr alloy

The Corrosion Behavior of AZ91D Magnesium Alloy in Simulated Haze Aqueous Solution