Abstract:Compressible flow past a circular cylinder at an inflow Reynolds number of 2 x 10 5 is numerically investigated by using a constrained large-eddy simulation (CLES) technique. Numerical simulation with adiabatic wall boundary condition and at a free-stream Mach number of 0.75 is conducted to validate and verify the performance of the present CLES method in predicting separated flows. Some typical and characteristic physical quantities, such as the drag coefficient, the root-mean-square lift fluctuations, the Strouhal number, the pressure and skin friction distributions around the cylinder, etc. are calculated and compared with previously reported experimental data, finer-grid large-eddy simulation (LES) data and those obtained in the present LES and detached-eddy simulation (DES) on coarse grids. It turns out that CLES is superior to DES in predicting such separated flow and that CLES can mimic the intricate shock wave dynamics quite well. Then, the effects of Mach number on the flow patterns and parameters such as the pressure, skin friction and drag coefficients, and the cylinder surface temperature are studied, with Mach number varying from 0.1 to 0.95. Non-monotonic behaviors of the pressure and skin friction distributions are observed with increasing Mach number and the minimum mean separation angle occurs at a subcritical Mach number of between 0.3 and 0.5. Additionally, the wall temperature effects on the thermodynamic and aerodynamic quantities are explored in a series of simulations using isothermal wall boundary conditions at three different wall temperatures. It is found that the flow separates earlier from the cylinder surface with a longer recirculation length in the wake and a higher pressure coefficient at the rear stagnation point for higher wall temperature. Moreover, the influences of different thermal wall boundary conditions on the flow field are gradually magnified from the front stagnation point to the rear stagnation point. Moreover, the influences of different thermal wall boundary conditions on the flow field are graduallymagnified from the front stagnation point to the rear stagnation point. It is inferred that the CLES approach in its current version is a useful and effective tool for simulating wall-bounded compressible turbulent flows with massive separations.

Constrained Large-Eddy Simulation of Turbulent Flow and Heat Transfer in a Stationary Ribbed Duct

Constrained Large-Eddy Simulation for Aerodynamics

Constrained Large-Eddy Simulation of Compressible Flow Past a Circular Cylinder

Constrained Large-Eddy Simulation of Separated Flow in a Channel with Streamwise-Periodic Constrictions

Constrained Large-Eddy Simulation of a Spatially Evolving Supersonic Turbulent Boundary Layer at M = 2.25

Constrained large-eddy simulation of laminar-turbulent transition in channel flow

Constrained Large Eddy Simulation of Wall-Bounded Turbulent Flows

Constrained Large-Eddy Simulation of Turbulent Flow over Inhomogeneous Rough Surfaces

Constrained Large-Eddy Simulation and Detached Eddy Simulation of Flow Past a Commercial Aircraft at 14 Degrees Angle of Attack

Large Eddy Simulation of Supersonic Flow in Ducts with Complex Cross-sections

Transition-based Constrained Large-Eddy Simulation Method with Application to an Ultrahigh-Lift Low-Pressure Turbine Cascade Flow

LAMINAR FLOW AND HEAT TRANSFER IN THE DEVELOPING REGION OF HELICAL SQUARE DUCTS

Large-Eddy vs. Reynolds-Averaged Navier–Stokes Simulations of Flow and Heat Transfer in a U-Duct with Unsteady Flow Separation

Reynolds Stress Constrained Large Eddy Simulation of Separation Flows in a U-duct

Constrained Large-Eddy Simulation of Supersonic Turbulent Boundary Layer over a Compression Ramp

Large eddy simulation of free surface turbulent channel flow with heat transfer

Experimental and Numerical Investigation of Heat Transfer Inside Two-Pass Rib Roughened Duct (AR = 1:2) under Rotating and Stationary Conditions

Direct numerical simulation of turbulent duct flow with inclined or V-shaped ribs mounted on one wall

Investigating Enhanced Convection Heat Transfer in 3D Micro-Ribbed Tubes Using Inverse Problem Techniques

Reynolds-Constrained Large-Eddy Simulation: Sensitivity to Constraint and SGS Models

Numerical study of air-side performance of a finned flat tube heat exchanger with crossed discrete double inclined ribs