Abstract:Powder metallurgy (PM) α + β Ti-4Al-4Mo-4Sn-0.5Si alloys were fabricated through thermomechanical powder consolidation of TiH 2 -based powder compacts with two different processing routes: one involving blending the elemental powders (BE route) and the other involving mechanical milling a blend of elemental powders (MM route). With the MM + annealing + solution and aging (STA) route, a hierarchical microstructure consisting of necklace-like micron-scaled grain boundary α (α GB ) segments and isolated submicron-scaled primary α (α p ) rods dispersed in a β transformed structure (β t ) matrix containing a high number density of nano-scaled secondary α (α s ) laths was produced in the alloy. The alloy with the hierarchical microstructure achieved an excellent combination of a very high yield strength of 1339 MPa,an ultimate tensile strength of 1467 MPa and an excellent ductility of 10.4%. The increased strength was mainly due to the high fraction of β t matrix in which the fine-dispersed α s precipitates with different orientations efficiently blocked the dislocation motion during deformation. The excellent ductility achieved despite of the high flow stress can be attributed to the elimination of strain concentration in the α GB segments which prevented their cracking prior to the material reaching the necking point during plastic deformation. This was in contrast with the typical α/β t lamellar microstructure of the same alloy composition obtained with the BE + same heat treatment route where strain concentration in the α GB plates occurred due to the direct slip transmission from α colonies to adjacent parent α GB grains during plastic deformation, thus resulting in intergranular premature cracking. TEM observation demonstrated that the strain gradient from the α/β t interfaces to the domain interiors of both α GB segments and α p rods activated a high density of geometrically necessary dislocations near the interfaces, and caused an obvious synergistic strengthening effect which also contributed to the slow drop of strain hardening rate and thus was beneficial to improving the ductility.

Different Formation Routes of Pore Structure in Aluminum Powder Metallurgy Alloy

Formation and evolution mechanisms of micropores in powder metallurgy Ti alloys

Effect of Powder Characteristics on Relative Density and Porosity Formation During Electron Beam Selective Melting of Al2024 Aluminum Alloy

Grain structure and texture selection regimes in metal powder bed fusion

Influence of Soaking Time and Loading Rate on Semi-solid Compression of Porous Al-4Cu-Mg Alloy

Effect of Processing Route on Microstructure and Mechanical Properties of an Al-12Si Alloy

Aluminum Foam Sandwich: Pore Evolution Mechanism Investigation and Engineering Preparing Optimization

Effects of porosity on the mechanical properties of additively manufactured components: a critical review

Manufacturing of fine-grained structures by multilevel kinking mechanism through a novel periodic undulating compression method: An example 7075 aluminum alloy

Influence of Structure Development on Performance of Copper Composites Processed via Intensive Plastic Deformation

Modeling of Processing-Induced Pore Morphology in an Additively-Manufactured Ti-6Al-4V Alloy

Relationship between the Size and Inner Structure of Particles of Virgin and Re-Used MS1 Maraging Steel Powder for Additive Manufacturing

Formation and Microstructural Evolution of Ferritic ODS Steel Powders during Mechanical Alloying

Influence of Processing Routes to Enhance the Mechanical Properties of Mg–6Zn–1Y–3.5CeMM (wt.%) Alloy

Characterisation of structure, mechanical and corrosion properties of pure magnesium prepared by powder metallurgy route

Porosity in wire-arc directed energy deposition of aluminum alloys: Formation mechanisms, influencing factors and inhibition strategies

Hierarchical microstructure and strain partition of a PM α + β titanium alloy with an ultrahigh strength-ductility synergy

In-situ tensile deformation behavior of powder metallurgy Ti6Al4V alloys

The coupling effect of vacuum, pressure and temperature on microstructure and mechanical properties of PM aluminum alloy

Quantitative Characterization of Metal Powder Morphology, Size Distribution, and Flowability for Additive Manufacturing

Effects of KoBo-Processing and Subsequent Annealing Treatment on Grain Boundary Network and Texture Development in Laser Powder Bed Fusion (LPBF) AlSi10Mg Alloy