Abstract:A two‐step optimization strategy enhances both density‐of‐state effective mass and multiple defects scattering with less compromising hole mobility, resulting in a ZTmax = 1.44 and a ZTavg = 1.28 (300–500 K) in Bi0.4Sb1.6Te2.95Se0.05 + 0.05 wt.% Ag5Te3. Moreover, by coupling n‐type zone‐melted Bi2Te2.7Se0.3, the 17‐pair thermoelectric module exhibits a competitive η = 6.1% at ΔT = 200 K for low‐grade heat harvest. Power generation modules utilizing thermoelectric (TE) materials are suitable for recycling widespread low‐grade waste heat (<600 K), highlighting the immediate necessity for advanced Bi2Te3‐based alloys. Herein, the substantial enhancement in TE performance of the p‐type Bi0.4Sb1.6Te3 (BST) sintered sample is realized by subtly incorporating the non‐stoichiometric Ag5Te3 and counteractive Se. Specifically, Ag atoms diffused into the BST lattice improve the density‐of‐states effective mass (md*) and boost the hole concentration for the suppressed bipolar effect. The addition of Se further improves md* prompting the room‐temperature power factor upgrade to 46 W cm−1 K−2. Concurrently, the lattice thermal conductivity is considerably lowered by multiple scattering sources exemplified by Sb‐rich nanoprecipitates and dense dislocations. These synergistic results yield a high peak ZT of 1.44 at 375 K and an average ZT of 1.28 between 300 and 500 K in the Bi0.4Sb1.6Te2.95Se0.05 + 0.05 wt.% Ag5Te3 sample. More significantly, when coupled with n‐type zone‐melted Bi2Te2.7Se0.3, the integrated 17‐pair TE module achieves a competitive conversion efficiency of 6.1% and an output power density of 0.40 W cm−2 at a temperature difference of 200 K, demonstrating great potential for practical applications.

Grain Size‐Dependent Thermoelectric Performances of Al2O3 Addition into BiSbTe Alloy During Heat Treatment Fabricated by Mechanical Alloying

Hierarchical Phonon Scattering from Nano to Macro Scale in Ag-Nano/TiO2-Micro Particle-Decorated p-type Bismuth Telluride Bulk Composites

Enhanced thermoelectric performance of Bi0.3Sb1.7Te3 based alloys by dispersing TiC ceramic nanoparticles

High ZT Value and Ultralow Lattice Thermal Conductivity Induced by Edge Dislocations Coupled with the Superlattice Structure in Ag-Doped BST Alloy

Enhanced Thermoelectric Performance of P‐Type (Bi,Sb)2Te3 by Incorporating Non‐Stoichiometric Ag5Te3 and Refining Te‐Se Ratio

Effect of Starting Powder Particle Size on the Thermoelectric Properties of Hot-Pressed Bi0.3Sb1.7Te3 Alloys

Enhanced Thermoelectric Performance of Bi0.4Sb1.6Te3 Based Composites with CuInTe2 Inclusions

Achieving High Thermoelectric Performance in p-Type BST/PbSe Nanocomposites through the Scattering Engineering Strategy

Boron-Mediated Grain Boundary Engineering Enables Simultaneous Improvement of Thermoelectric and Mechanical Properties in N-Type Bi<sub>2</sub>Te<sub>3</sub>

High-Thermoelectric Performance of Nanostructured Bismuth Antimony Telluride Bulk Alloys

Enhanced Thermoelectric and Mechanical Performances in Sintered Bi0.48Sb1.52Te3-AgSbSe2 Composite.

Nanostructuring and band engineering boosting thermoelectric performance of Bi-Sb-Te alloys via CsBr doping

Influence of Ag2te Doping on the Thermoelectric Properties of P-Type Bi0.5sb1.5te3 Bulk Alloys

Grain Recovery Facilitated Low-Angle Grain Boundaries and Texture for High-Performance Bisbte Alloys

Enhanced thermoelectric and mechanical properties of Bi0.5Sb1.5Te3 alloy with dispersed yttrium oxide ceramic nanoparticles

Enhanced Thermoelectric Properties of N-Type Bi2te3-Based Nanocomposite Fabricated by Spark Plasma Sintering

BiSbTe-based nanocomposites with high ZT: The effect of SiC nanodispersion on thermoelectric properties

Simultaneously Improved Thermoelectric and Mechanical Properties Driven by MgB2 Doping in Bi0.4Sb1.6Te3 Based Alloys

Enhancing thermoelectric performance of n-type Bi2Te2.7Se0.3 through the incorporation of MnSb2Se4 nanoinclusions

Tunable Electrical Conductivity and Simultaneously Enhanced Thermoelectric and Mechanical Properties in n‐type Bi2Te3

Hierarchical nano-/micro-architecture phonon scattering of p -type Bismuth Telluride bulk composites with Ag-TiO 2 nano particles synthesized by fluidized bed spray coating method