Abstract:With the long-term water-flooding development of the reservoir, the non-homogeneity of the formation is increasing and the reservoir environment is deteriorating; the microspheres used for deep plugging have shown disadvantages, such as poor temperature and salt resistance and faster expansion. In this study, a polymeric microsphere was synthesized that is resistant to high temperature and high salt and can achieve slow expansion and slow release for deep migration. P(AA-AM-SA)@TiO2 polymer gel/inorganic nanoparticle microspheres were prepared by reversed-phase microemulsion polymerization using acrylamide (AM) and acrylic acid (AA) as monomers, 3-methacryloxypropyltrimethoxysilane (KH-570)-modified TiO2 as the inorganic core, and sodium alginate (SA) as a temperature-sensitive coating material. Through single-factor analysis of the polymerization process, the optimal synthesis conditions were determined as follows: the oil(Cyclohexane)-water volume ratio was 8:5, the emulsifier mass ratio (Span-80:Tween-80) was 3:1 (10 wt% of the total system amount), the stirring speed was 400 r/min, the reaction temperature was 60 °C, and the initiator (ammonium persulfate and sodium bisulfite) dosage was 0.6 wt%. The size of the dried polymer gel/inorganic nanoparticle microspheres prepared by the optimized synthesis conditions was 10~40 μm with uniform particle size. The observation of P(AA-AM-SA)@TiO2 microspheres reveals that the Ca elements are uniformly distributed on the microspheres, and FT-IR indicates that the synthesized product is the target product. TGA shows that the polymer gel/inorganic nanoparticle microspheres have better thermal stability after the addition of TiO2, with a larger mass loss at 390 °C, which can adapt to the medium-high permeability reservoir environment. The thermal and aqueous salinity resistance of the P(AA-AM-SA)@TiO2 microspheres was tested, and the cracking temperature of P(AA-AM-SA)@TiO2 microsphere temperature-sensitive material was 90 °C. It still has favorable water absorption and swelling performance under the sodium salt concentration of 2.5 × 104 mg/L and can tolerate calcium salt up to 2.0 × 104 mg/L. Plugging Performance Test results show that the microspheres have good injectability between the permeability of 1.23 and 2.35 μm2 and good plugging effect near the permeability of 2.20 μm2. At high temperature and high salinity, P(AA-AM-SA)@TiO2 microspheres have a remarkable effect on profile control and water shutoff, the plugging rate reaches 95.3%, and the oil recovery rate is increased by 12.89% compared with water flooding, achieving the effect of slow swelling and slow release.

Effect of nano TiO2 and SiO2 on gelation performance of HPAM/PEI gels for high-temperature reservoir conformance improvement

Carbon Nanofiber-Enhanced HPAM/PEI Gels for Conformance Control in Petroleum Reservoirs with High Temperatures

Preparation and temperature resistance mechanism of nanoparticle-enhanced polymer gel

New Insights and Experimental Investigation of High-Temperature Gel Reinforced by Nano-SiO2

Nano-silica hybrid polyacrylamide/polyethylenimine gel for enhanced oil recovery at harsh conditions

Synthesis and properties of elevated temperature hydrogels for enhanced oil recovery based on AM/AMPA/NVP copolymer and silica nanoparticles

Experimental study of the hydroquinone (HQ)–hexamethylenetetramine (HMTA) gel system for conformance improvement in extremely high‐temperature reservoirs

Preparation of high-temperature gels for enhanced oil recovery using methyl etherized melamine-formaldehyde resin

Development of dual-crosslinked nanocomposite gel for water management in high-temperature reservoirs

Preparation Method and Performance Evaluation of a Gel Based on AM/AMPS Copolymer

Nano Composite Polymer Composition for Water Shutoff Treatment at High Formation Temperature

Development and Gelation Mechanism of Ultra-High-Temperature-Resistant Polymer Gel

Preparation and rheological properties of organic zirconium crosslinked KGM/HPAM gel

The experimental study of silica nanoparticles strengthened polymer gel system

Study on increasing polymer gel strength with Janus nanoparticles and its feasibility in profile control and water plugging

Tuning morphology and mechanical property of polyacrylamide/Laponite/titania dual nanocomposite hydrogels by titania

Strengthening the Hydrogel for Lost Circulation Control through In Situ Self-Assembled Nanocomposite Networks

Multiple Hydrogen Bonding-Assisted High-Strength Hydrogel of Silica/Polyacrylamide Nanocomposite Cross-Linked with Polyethylenimine

Synthesis and Performance Evaluation of Alginate-Coated Temperature-Sensitive Polymer Gel Microspheres

Gelation and Plugging Performance of Low-Concentration Partially Hydrolyzed Polyacrylamide/Polyethyleneimine System at Moderate Temperature and in Fractured Low-Permeability Reservoir

Optimization of the Methods to Develop Stable Polymer Gels for Water Management in Medium- and Ultra-High-Salinity Reservoirs