Abstract:The surface and boundary defects present in the perovskite film are reported to be nonradiative recombination and degradation centers, restricting further improvement of the power conversion efficiency (PCE) and long-term stability of perovskite solar cells. To address this problem, herein, we introduce a fluorine-substituted small molecular material 2FBTA-1 as a bifunctional buffer layer to efficiently passivate the surface defects of perovskite and tune the energy level alignment between the perovskite/2,2′,7,7′-tetrakis(N,N-di-(p-methoxyphenyl)amino)-9,9′-spirobifluorene (Spiro-OMeTAD) interface. X-ray photoelectron spectroscopy shows that with the insertion of 2FBTA-1 between perovskite and Spiro-OMeTAD, the metallic Pb0 defects and uncoordinated Pb2+ defects are well restricted. Consequently, the average PCE is distinctly improved from 18.4 ± 0.51 to 20.3 ± 0.40%. Moreover, the long-term stability of unencapsulated devices with 2FBTA-1 treatment under ambient conditions (relative humidity 40–60%) is effectively enhanced, retaining 87% of the initial efficiency after storage for 500 h.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c21975?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c21975</a>.Enlarged image of XRD patterns, UV–vis absorption spectra and UPS measurement of the perovskite film w/ and w/o 2FBTA-1, IR spectra of PbI2 w/ and w/o 2FBTA-1 treatment, and cross-sectional SEM image of 2FBTA-1-treated PSC (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c21975/suppl_file/am0c21975_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

A thioacetamide interlayer anchoring TiO 2 and (FAPbI 3 ) 1− x (MAPbBr 3 ) x for high‐performance perovskite solar cells

Multifunctional Thiophene-Based Interfacial Passivating Layer for High-Performance Perovskite Solar Cells

Perovskite Surface Passivation Using Thiophene-Based Small Molecules for Efficient and Stable Solar Cells

All-in-one Additive Enables Defect Passivated, Crystallization Modulated and Moisture Resisted Perovskite Films Toward Efficient Solar Cells

An Efficient Trap Passivator for Perovskite Solar Cells: Poly(propylene glycol) bis(2-aminopropyl ether)

Polyaspartic Acid Sodium Interfacial Layer Enhances Surface Trap Passivation in Perovskite Solar Cells

Efficient and Stable Perovskite Solar Cell Achieved with Bifunctional Interfacial Layers.

Efficient Bifacial Passivation with Crosslinked Thioctic Acid for High‐Performance Methylammonium Lead Iodide Perovskite Solar Cells

Suppressing Excess Lead Iodide Aggregation and Reducing N‐Type Doping at Perovskite/HTL Interface for Efficient Perovskite Solar Cells

Molecularly Tailored Surface Defect Modifier for Efficient and Stable Perovskite Solar Cells

Phenyltrimethylammonium Chloride Additive for Highly Efficient and Stable FAPbI3 Perovskite Solar Cells

Surface Defect Passivation and Energy Level Alignment Engineering with a Fluorine-Substituted Hole Transport Material for Efficient Perovskite Solar Cells

A Biopolymer Heparin Sodium Interlayer Anchoring TiO2 and MAPbI3 Enhances Trap Passivation and Device Stability in Perovskite Solar Cells.

Tetramethylammonium hexafluorophosphate interface modification for high-efficiency perovskite solar cells

Dimensionality-Controlled Surface Passivation for Enhancing Performance and Stability of Perovskite Solar Cells via Triethylenetetramine Vapor

Tri‐Brominated Perovskite Film Management and Multiple‐Ionic Defect Passivation for Highly Efficient and Stable Solar Cells

Passivating Defects via Retarding the Reaction Rate of FAI and PbI2 Enables Stable Perovskite Solar Cells

Surface charge-transfer doping for highly efficient perovskite solar cells

Vacancies substitution induced interfacial dipole formation and defect passivation for highly stable perovskite solar cells

Introduction of Multifunctional Triphenylamino Derivatives at the Perovskite/HTL Interface To Promote Efficiency and Stability of Perovskite Solar Cells

2-CF3-PEAI to eliminate Pb0 traps and form a 2D perovskite layer to enhance the performance and stability of perovskite solar cells