Abstract:Abstract Central cracking in cross-wedge-rolled workpieces results in high wastage and economic loss. Recent cross-wedge rolling tests on two batches of steel showed that one batch formed central cracks, while the other was crack-free. The batches were both nominally of the same chemical composition and thermomechanical treatment history. In addition, both batches had passed all the standard quality assessments set for conventional forging processes. It was suspected that the different cracking behaviours were due to differences in microstructure between the two as-received steel billets, and the material in cross-wedge rolling (CWR) was more sensitive to the initial microstructure compared with other forging processes due to its specific loading condition including ostensibly compression and large plastic strain. Nevertheless, no previous study of this important problem could be identified. The aim of this study is, therefore, to identify the key microstructural features determining the central crack formation behaviour in CWR. The hot workability of the as-received billets was studied under uniaxial tensile conditions using a Gleeble 3800 test machine. Scanning electron microscope with energy-dispersive X-ray spectroscopy and electron backscatter diffraction was applied to characterise, quantitatively analyse, and compare the chemical composition, phase, grain, and inclusions in these two billets, both at room temperature and also at the CWR temperature (1080 °C). Non-metallic inclusions (oxides, sulphides, and silicates) in the billets were determined to be the main cause of the reported central cracking problem. The ductility of the steels at both room and elevated temperatures deteriorated markedly in the presence of the large volumes of inclusions. Grain boundary embrittlement occurred at the CWR temperature due to the aggregation of inclusions along the grain boundaries. It is suggested that a standard on specifying the inclusion quantity and size in CWR billets be established to produce crack-free products.

Quality reliability analysis of flash welding joint of cold-rolled 50JW800 silicon steel strip

DIC/DSI Based Studies on the Local Mechanical Behaviors of HR3C/T92 Dissimilar Welded Joint During Plastic Deformation

Large Concave Roll Technology For Hot Rolled Silicon Steel

Bonding Properties Evaluation for an EBW Joint of RAFM Steel by Using Notched Small Tensile Specimens

Study on microstructure evolution and mechanical properties of high-strength low-alloy steel welds realized by flash butt welding thermomechanical simulation

Study on the Microstructure and Properties of Flash-Butt Welding Joints of High Nitrogen Steel

Microstructural effects on central crack formation in hot cross-wedge-rolled high-strength steel parts

Microstructural and mechanical properties of Al–Mg–Si–Cu joint fabricated by rotary friction welding

The sensitivity analysis of microstructure and mechanical properties to welding parameters for linear friction welded rail steel joints

Failure Analysis on the Collapse of Leaf Spring Steels During Cold-Punching

Cause Analysis and Preventive Measures against Cracks in 15Cr1Mo1V Steel Welded Joint in Service

Studies on Mechanism of Zigzag Crack Forming Process in Weld Metal of Narrow Gap Submerged Arc Welding of Thick Plate

Numerical Analysis of Edge Cracking in High-Silicon Steel during Cold Rolling with 3D Fracture Locus

Prediction of phase volume fraction and residual stress distribution in Q960E steel single-pass re-melting joint

Effect of heat treatment on microstructure and mechanical properties of AG728 steel joints welded with ER90S-G wires

HAZ Effects in Hot-Rolled Dual-Phase Steel During Flash Butt Welding of Wheel Rims

Physical Simulation and Numerical Simulation of Flash Butt Welding for Innovative Dual Phase Steel DP590: A Comparative Study

Insights into microstructure evolution and fracture mechanisms of welded joints of high strength steel patchwork components

Study on the microstructure and failure mechanisms for flat resistance element welding-bonding aluminium alloy/Q235 steel joints

Microstructure and abnormal mechanical properties under the coupling effect of strain and temperature for friction-stir-welded joints of Al-Mg-Si alloy

Flash butt welding on microstructures and mechanical properties of joints for high strength acid resistant steel