Abstract:Aluminium alloys were widely applied in rail transit, ships and aerospace owing to their unique properties, such as low density, high strength and stiffness, outstanding corrosion resistance and low temperature performance. As a type of structure material, aluminium alloy joining was inevitable. However, these alloys were often considered very difficult to weld using traditional fusion welding technique since the welding seams were often accompanied with metallurgical defects, large deformation and stress. Friction stir welding (FSW), an innovative solid-state welding technology invented at the welding institute (TWI), was seen by designers as an effective joining methods in welding aluminium alloys due to low heat input, small stress-strain and environment friendly. In this work, 0.8 mm thick plate of 6061-T6 aluminium alloy was successfully welded by use of high rotational speed fiction stir welding technology. The microstructure and mechanical property of the butt joints prepared by high rotational speed friction stir welding were analysed in detail. The results show that the well surface topography and excellent bonding interface existed in the nugget zone (NZ) were observed. Both of the microhardness of the weld seam was lower than that of the substrate. The lowest microhardness of the butt joints located between the thermo-mechanically affected zone (TMAZ) and heat affected zone (HAZ). Compared with the conventional rotational speed, the number of beta-Mg2Si, Al2CuMg and Al8Fe2Si precipitated phases existed in the NZ was more, which made the microhardness in the NZ improved significantly. The rod-shaped precipitates (Mg2Si) have the greatest influence on the microhardness. The excellent mechanical properties were obtained at the rotational speed of 8000 r/min and welding speed of 1500 mm/min. The maximum tensile strength was 301.8 MPa, which was 85.8% of the as-received 6061-T6 (351.7 MPa). And the toughness-brittleness fracture mode appeared.

Microstructures and Properties of Aluminum–Copper Lap‐Welded Joints by Cold Metal Transfer Technology

Microstructure and Properties of Aluminum Aa6061-T6 to Copper (Cu)-T2 Joints by Cold Metal Transfer Joining Technology

Microstructures and Mechanical Behavior of Aluminum-Copper Lap Joints

Microstructure and Properties of Dissimilar Butt Joints of Aluminum to Copper by Cold Metal Transfer with Preheating

Microstructure and mechanical properties of cold metal transfer welded aluminium/nickel lap joints

Investigation on Microstructure and Mechanical Properties of Al/Cu Butt Joints by CMT Method in Asymmetrical V-groove Configuration

Microstructures and Properties of Friction Stir Welded Al-Cu Lap Joints

Microstructure Evolution and Mechanical Properties of Friction Stir Spot Welded Dissimilar Aluminum-Copper Joint

Microstructure and Mechanical Properties of Ultrasonic Welded Joint of 1060 Aluminum Alloy and T2 Pure Copper

Microstructures and Mechanical Properties of Thin Plate Aluminium Alloy Joint Prepared by High Rotational Speed Friction Stir Welding

Microstructural characterization and mechanical properties of micro friction stir welded dissimilar Al/Cu ultra-thin sheets

Microstructure evolution and mechanical properties of Cu–Al joints by ultrasonic welding

Microstructural Evolution and Mechanical Properties of Dissimilar Al–Cu Joints Produced by Friction Stir Welding

Microstructure and Mechanical Performance of Cold Metal Transfer Spot Joints of AA6061-T6 to Galvanized DP590 Using Edge Plug Welding Mode

Interfacial layer regulation and its effect on mechanical properties of Ti6Al4V titanium alloy and T2 copper dissimilar joints by cold metal transfer welding

Effect of lap configuration on the microstructure and mechanical properties of dissimilar ultrasonic metal welded copper-aluminum joints

Metallurgical joining of aluminium and copper using resistance spot welding: microstructure and mechanical properties

Microstructure and Mechanical Behaviour of Cold Metal Transfer Welded Mg/Al Dissimilar Joint Using Wire Az31 As Filler Metal

Microstructure Characteristics and Properties of Mg/Al Dissimilar Metals Made by Cold Metal Transfer Welding with ER4043 Filler Metal

Microstructure and mechanical properties of 1350 industrial pure aluminum and pure copper joints prepared by friction stir welding

Cold Metal Transfer Spot Welding of 1 Mm Thick AA6061-T6