Abstract:The need for 2219 aluminum alloy and 2195 Al–Li alloy dissimilar friction stir welding (FSW) arises as the conventional 2219Al alloy was gradually replaced by the novel 2195Al alloy in fabrication of fuel tanks. However, the systematic investigation about the effect of welding parameters and material positioning on the microstructure evolution and mechanical properties of dissimilar FSW 2219Al/2195Al joints is lacking. In the present study, 2219Al-T8/2195Al-T8 plates were subjected to FSW under rotation rates of 800–1200 rpm and welding speeds of 200–800 mm min −1 with placing 2219Al-T8 alloys on the advancing side (AS) and retreating side (RS), respectively. The results showed that sound FSW joints were obtained under all the welding conditions. Welding parameters and material positioning affected the joint strength and fracture failure behavior. The FSW thermal cycle resulted in low hardness zones (LHZs) on both the 2219Al-T8 and 2195Al-T8 sides. The LHZ on the 2219Al-T8 side, characterized by partial coarsening of θ ′ (Al 2 Cu) precipitates and dissolution of the residual precipitates, showed the minimum hardness in the entire FSW joints. When 2219Al-T8 alloy was placed on the AS, the LHZ on the 2219Al-T8 side experienced higher peak temperature, and therefore more dissolution of θ ′ than that on the RS, thereby obtaining higher tensile strength. The tensile strength of the FSW joints at room temperature and − 196 °C largely increased as the welding speed increased from 200 to 400 mm min −1 . The FSW joints presented much higher tensile strength at − 196 °C than that at room temperature under the identical welding parameters and material position. The FSW joints fractured along the LHZ on the 2219Al-T8 side during tension. For the bending testing, the up and down bending failure angles were about 91–117° and 88–109°, respectively, with the weak zone appearing in "S" line or HAZ on the 2195Al-T8 side.

Microstructure and XRD Analysis of FSW Joints for Copper T2/aluminium 5A06 Dissimilar Materials

Microstructure and Mechanical Performance of FSWed Joint of T2 Copper and AA 1061

Dissimilar friction stir welding of 2219-T8 and 2195-T8 aluminum alloys: part I—microstructure evolution and mechanical properties

Microstructural Characterisation and Mechanical Properties of Dissimilar AA5083-copper Joints Produced by Friction Stir Welding

Microstructure, microhardness and mechanical behavior of dissimilar AA7075/AA6061 alloys under friction stir welding

Influence of FSW process on dissimilar T-joint of aluminum alloy to pure copper

Microstructure, mechanical and fracture properties of friction stir welded 2195 Al-Li alloy joints

Microstructure and Mechanical Properties Analysis of Al/Cu Dissimilar Alloys Joining by Using Conventional and Bobbin Tool Friction Stir Welding

Residual Stress, Microstructure and Mechanical Properties in Thick 6005A-T6 Aluminium Alloy Friction Stir Welds

Microstructure Evolution and Mechanical Properties of Friction Stir Welded Al–Cu–Li Alloy

Microstructural characterization and mechanical properties of micro friction stir welded dissimilar Al/Cu ultra-thin sheets

Mechanical properties and corrosion resistance study of dissimilar metal thin sheet friction stir welded joints

Analysis of the Microstructure and Properties of Friction Stir Weld Zones in the Al 2139‐T8 Alloy

Comparative Analysis of Microstructure Evolution and Mechanical Properties of Dissimilar Welded Joints of AA7075/AA6061 via Friction Stir Welding, Tungsten Inert Gas Welding, and Tungsten Inert Gas + Friction Stir Processing

Effect of Tool-Workpiece Relative Position on Microstructure and Mechanical Properties of Al-Cu Dissimilar Friction Stir Weld

Microstructure and Mechanical Properties of Dissimilar Double-Side Friction Stir Welds Between Medium-Thick 6061-T6 Aluminum and Pure Copper Plates

Microstructure, Corrosion and Mechanical Properties of Medium-Thick 6061-T6 Alloy/T2 Pure Cu Dissimilar Joints Produced by Double Side Friction Stir Z Shape Lap-Butt Welding

Microstructure and fatigue performance of friction stir welded joints of 2A12‐T4 and 7075‐T6 dissimilar aluminum alloy

Experimental Study on Mechanical Behaviour of Friction Stir Welded Aluminium Alloy Butt Joints

Investigation of mechanical, metallurgical and corrosion characteristics of friction stir welded dissimilar AA 5052-H32 and AA 6061-T6 joints

Microstructure and mechanical characteristics of AA6061-T6 joints produced by friction stir welding, friction stir vibration welding and tungsten inert gas welding: A comparative study