Abstract:In this dissertation, the relationships between structure-mechanical properties-deformation mechanisms in face-centered cubic (FCC) and body-centered cubic (BCC) metallic nanowires have been studied using in situ TEM nanomechanical testing. It is well known that smaller is stronger and the widely-observed size effect is believed to arise from dislocation interactions inside nanocrystals. However, the interaction mechanisms in small-volume nanocrystals remain unexplored. Here, it was found that surface-nucleated dislocations can strongly interact inside the confined volume of Au nanowires, which led to a new type of dislocation-originated stacking fault tetrahedra (SFT), at variance to the widely-believed vacancy-originated SFT. The atomic-scale processes of nucleation, migration and annihilation of dislocation-originated SFT were revealed, shedding new light onto the strain hardening and size effect in small-volume materials. Although nanoscale twinning is an effective mean to enhance the strength of metals, twin-size effect on the deformation and failure of nanotwinned metals remains largely unexplored, especially at the minimum twin size. Here, a new type of size effect in nanotwinned Au nanowires is presented. As twin size reaches the angstrom-scale, Au nanowires exhibit a remarkable ductile-to-brittle transition that is governed by the heterogeneous-to-homogeneous dislocation nucleation transition. Quantitative measurements show that approaching such a nanotwin size limit gives rise to the ultra-high strength in Au nanowires, close to the ideal strength limit of perfect Au. Twinning is a fundamental deformation mode that competes against dislocation slip in crystals. At the nanoscale, higher stresses are required for plastic deformation than that in bulk, which favors twinning over dislocation slip. Indeed, deformation twinning has been well-documented in FCC nanocrystals. However, it remains unexplored in BCC nanostructures. Here, it shows that twinning is the dominant deformation mode in BCC-tungsten nanocrystals. A competition between twinning and dislocation slip occurs when changing the loading orientations, attributed to the defect growth controlled plasticity in BCC nanocrystals. Several important commonalities and differences in FCC and BCC nanocrystals deforming at nanoscale are further proposed. The results from this dissertation advance fundamental understanding of plastic deformation in a broad class of metals and alloys, and are of technological importance for degradation control and future design of ultra-strength nanomaterials.

Characterizing the Nano-Structure and Defect Structure of Nano-Scaled Non-Ferrous Structural Alloys

In Situ TEM Study on the Nanomechanical Behaviors of Metallic Nanowires

In Situ Atomistic Observation of the Deformation Mechanism of Au Nanowires with Twin–twin Intersection

Influence of Defects and Crystallographic Orientation on Mechanical Behavior of Nanocrystalline Aluminium

3D Characterization of a Nanostructured Al-Cu-Mg Alloy

Atomic Simulation of the Effect of Orientation on Tensile/compressive Properties in Nickel-Based Single Crystal Superalloys

Development and Application of a Novel Precession Electron Diffraction Technique to Quantify and Map Deformation Structures in Highly Deformed Materials—as Applied to Ultrafine-Grained Titanium

Precession Electron Diffraction Assisted Orientation Mapping of Gradient Nanostructure in a Ni-based Superalloy

Non-destructive detection of cross-sectional strain and defect structure in an individual Ag five-fold twinned nanowire by 3D electron diffraction mapping

Influence of load orientations with respect to twin boundaries on the deformation behaviors of high-entropy alloy nanocrystals

Twinning/detwinning-mediated Grain Growth and Mechanical Properties of Free-Standing Nanotwinned Ni Foils: Grain Size and Strain Rate Effects

Anisotropic Mechanical Properties and Deformation Mechanisms of Nanotwinned Ni and Ni Alloys With Extremely Fine Twin Boundary Spacings

γ′-size effect on the deformation microstructure and texture in a Ni-based superalloy using in-situ neutron diffraction

Microstructural Characterization by Automated Crystal Orientation and Phase Mapping by Precession Electron Diffraction in TEM: Application to Hot Deformation of a γ-TiAl-based Alloy

On the nature of nano twin-induced shear band formation in a dispersion strengthened copper alloy under micro-mechanical loading

Atomistic investigation on the anisotropic elastic and plastic responses of nanotwinned metals

Twin Spacing and Grain Size Dependent Tensile Deformation Mechanism of a Nano-Ploycrystalline Ni-based Alloy

A Thermally Activated Dislocation-Based Constitutive Flow Model of Nanostructured FCC Metals Involving Microstructural Evolution

2D and 3D orientation mapping in nanostructured metals: A review

Sub-nanometer-scale Mapping of Crystal Orientation and Depth-Dependent Structure of Dislocation Cores in SrTiO3

Precession Electron Diffraction Assisted Characterization of Deformation in Α and Α+β Titanium Alloys