Abstract:Ultrafine grained (UFG) metallic materials arouse a great interest clue to their excellent mechanical properties. The UFG materials, produced by severe plastic deformation (SPD) technique such as channel angular pressing (ECAP) and high pressure torsion (HPT), exhibit obvious improvement in strength but a large decrease in their thermal stability and ductility. In this article; an UFG QBel.7 copper alloy with good comprehensive properties was prepared by multi directional compression (MDC) at room temperature and subsequent annealing at high temperature. The deformed and subsequent annealed microstructures were investigated by OM, TEM and SEM/EBSD techniques. The integrated flow curves plotted over a number of compression passes increase to a. maximum at moderate strains of 1 to 2 followed by steady state like flow at high cumulative strains. Fine grains were not observed even at a higher cumulative stain of Sigma epsilon=4.8, although there were many sub grains when the samples were deformed to Sigma epsilon=2.4. This indicates that the dynamic recrystallization or recovery was completely inhibited by Fine precipitates. Static recrystallization (SRX) of the MDCed structure at 973 K was also investigated. With the increment of cumulative strains, the effect of grain refinement became more obvious, but the thermal stability was getting worse. At a medium strain of Sigma epsilon=2.4, the minimal grain size of 0.8 mu m could be developed with an excellent combination of properties. The formation of ultrafine grains is attributed to the development from low angle boundaries to medium angle boundaries to large angle boundaries. The change of the average grain size with annealing time could be divided into three, stages: a recovery period for grain refinement, rapid grain refinement and normal grain growth.

Effects of Temperature, Strain Rate and Specimen Size on the Deformation Behaviors at Micro/meso-Scale in Ultrafine-Grained Pure Al

Effect of Grain Size and Specimen Dimensions on Micro-Forming of High Purity Aluminum

Microstructural Evolution at Micro/Meso-Scale in an Ultrafine-Grained Pure Aluminum Processed by Equal-Channel Angular Pressing with Subsequent Annealing Treatment

Micro-deformation Behavior in Micro-Compression with High-Purity Aluminum Processed by ECAP

Effect of Grain Size on Formability and Deformation Mechanism of High‐Purity Aluminum during Micro‐Embossing Process at Elevated Temperature

Effect of Strain Rate on the Tensile Behavior of Ultra-Fine Grained Pure Aluminum

Constitutive relationship of micro-deformation in an ultrafine-grained pure aluminum

Micro-Embossing Process in Ultrafine-Grained Pure Aluminum Processed by Equal-Channel Angular Pressing with Elevated Temperature

Cooperative Effect of Grain Size and Cryogenic Temperature on Deformation Behavior and Mechanism of Commercial Pure Al Sheets

Effect of Grain Size on Hot Deformation Behavior of a New High Strength Aluminum Alloy

Grain Boundary Sliding and Strain Rate Sensitivity of Coarse and Fine/Ultrafine Grained 5083 Aluminum Alloys

Temperature And Strain Rate Sensitivity Of Ultrafine-Grained Copper Under Uniaxial Compression

Mechanism of considerable strain hardening in ultrafine-grained pure aluminum sheets at cryogenic temperatures

Effect of Strain Rate and Temperature on Dynamic Mechanical Behavior and Microstructure Evolution of Ultra-High Strength Aluminum Alloy

Effects of Temperature and Strain Rate on Compressive Mechanical Properties of Ultrafine-Grained CP Titanium

The Microstructure and Strength of UFG 6060 Alloy after Superplastic Deformation at a Lower Homologous Temperature

Influence of Grain Size in the Near-Micrometre Regime on the Deformation Microstructure in Aluminium

Mechanical responses, texture and microstructural evolution of high purity aluminum deformed by equal channel angular pressing

Effect of initial grain size on hot deformation behavior and recrystallization mechanism of Al-Zn-Mg-Cu alloy

Preparation of Ultrafine-Grained Copper Alloy by Annealing Treatment after Multi-Directional Compression

The Microstructures and Tensile Mechanical Properties of Ultrafine Grained and Coarse Grained Al-7Si-0.3Mg Alloy Rods Fabricated from Machining Chips