Abstract:A thermally sprayed deposit is formed by a stream of molten droplets impacting on a substrate followed by flattening, rapid solidification, and cooling processes. The individual molten droplets spread into thin lamellae, the stacking of which rudimentarily constitutes the thermal spray deposit. Accordingly, a thermally sprayed deposit is generally composed of lamellar structure. A portion of the deposit are voids, which constitute up to 20% of the total volume [1]. Some of the voids originated from insufficient liquid filling, prior to complete solidification, and incomplete wetting of molten liquid on the prior deposited lamella surfaces. Microcracks can be formed easily in the splats of brittle materials, in particular, ceramics owing to the quenching stresses that occur in splats [2]. Such microcracks are also a type of void within the deposits, and constitute a fraction of the overall porosity. The existence of voids in the coating will degrade the mechanical performance and corrosion resistance of thermal sprayed materials to a relatively low level compared to corresponding bulk materials. When a thermal sprayed coating is used under a certain mechanical loading, the loading may cause coating delamination or spallation in service owing to low adhesion of the coating to the substrate and limited cohesion within the coating. This undoubtedly leads to a decrease in the coating’s effective thickness or even direct exposure of the substrate surface to the operating environment. Many studies have revealed that the failure of the coating occurs readily from the interfaces among lamellae in the coating, and the interfaces between the coating and the substrate, for example, under localized load such as in abrasive wear [3] or erosion [4], fretting wear [5] and fracture mechanics test [6]. Even during the preparation of thermal sprayed samples for microstructure examination, pullouts do occur [7]. Such effect is attributed to the pores in the coating existing in the form of non-bonded lamellar interfaces [8], although in thermal barrier coatings (TBC), the performance may be improved by the existence of pores in the coating. Therefore, the modification of the microstructure of as-sprayed coating is desirable to improve coating performance. Up to now, many attempts

Adhesion and residual stress of plasma sprayed Alumina–titania coatings

Modeling of the residual stresses in plasma-spraying functionally graded ZrO2/NiCoCrAlY coatings using finite element method

Analysis on Deposition Process and Residual Stress in Plasma Spraying

Analysis on the Residual Stresses in Functionally Gradient ZrO_2/NiCoCrAlY Coatings

Investigation of stress field and failure mode of plasma sprayed Al2O3–13%TiO2 coatings under thermal shock

Fabrication and Evaluation of Plasma Sprayed Nanostructured Alumina–titania Coatings with Superior Properties

Effect of Thickness on the Residual Stress Profile of an Aluminum Cold Spray Coating by Finite Element Analysis

Tensile Adhesion Strength of Atmospheric Plasma Sprayed MgAl2O4, Al2O3 Coatings

Potential strengthening of erosion performance of plasma-sprayed Al2O3 coating by adhesives impregnation

Comparative Study of the Residual Stress in Plasma Sprayed Nanostracture and Conventional Structure Coatings

Thermomechanical modeling of a single splat solidification in plasma spraying

Microstructure and Surface Residual Stress of Plasma Sprayed Nanostructured and Conventional ZrO2‐8wt%Y2O3 Thermal Barrier Coatings

Dependency of fracture toughness of plasma sprayed Al 2 O 3 coatings on lamellar structure

Microstructure, adhesion, microhardness, abrasive wear resistance and electrical resistivity of the plasma sprayed alumina and alumina–titania coatings

Characterization of Alumina–3 Wt.% Titania Coating Prepared by Plasma Spraying of Nanostructured Powders

Adhesion Properties and Fracture Mechanism of Plasma Sprayed NiCrAl/Al2O3–13wt.%TiO2coatings by Post Annealing

Influence of FeCrAl Content on Microstructure and Bonding Strength of Plasma-Sprayed FeCrAl/Al2O3 Coatings

Residual Stresses of Plasma Sprayed ZrC-Based Coatings During Path-by-path and Layer-by-layer Deposition: Simulation and Experimental Verification

The dependency of microstructure and properties of nanostructured coatings on plasma spray conditions

Microstructure and Properties of Al2O3-13wt.%TiO2-Reinforced CoCrFeMnNi High-Entropy Alloy Composite Coatings Prepared by Plasma Spraying

Evaluation of Adhesion and Mechanical Properties of Plasma Sprayed NiCrAl/Al2O3-13wt.%TiO2 Coatings