Abstract:The severe oxidation of metal elements leads to a large amount of oxide inclusions that hinder the formation of metallurgical bonds across intersplat interfaces during thermal spraying in an ambient atmosphere, which further degrades the performance of thermally sprayed metal coatings. Controlling the oxidation of metal elements during spray deposition remains a significant challenge. In this paper, the thermodynamic and kinetic requirements of in-situ in-flight deoxidation by adding deoxidizer elements (diamond particles) to Fe / Al spray powders to achieve oxide-free molten droplets in an ambient atmosphere were investigated. Fe / Al / 2.5C composite powders containing 2.5wt.% diamond particles were prepared by mechanical alloying. Atmospheric plasma spraying (APS) was used to generate an oxide-free molten spray of FeAl particles at temperatures higher than 2 000 degrees C. This was achieved by the in-situ self-oxide cleaning effect of in-flight particles by carbon, which prevented metal droplets from oxidizing in an open atmosphere. For comparison, a FeAl coating was also deposited using Fe / Al composite powders prepared by mechanical alloying. The particle velocity and temperature were measured by a commercial thermal-spraying particle diagnostic system. The microstructures of the coatings were characterized by scanning electron microscopy and X-ray diffraction. The chemical compositions of the coatings were measured by inductively coupled plasma spectroscopy. The adhesive strength and hardness of the plasma-sprayed FeAl-based coatings were tested. The results show that under the combined effects of plasma- jet heating and the FeAl exothermic reaction, the heated FeAl spray particles could reach a high temperature of over 2 100 degrees C, which meets the thermodynamic conditions for carbon in-situ deoxidation. Because oxidation occurs from the surface of an in-flight molten droplet, to maintain continuous deoxidation of the molten FeAl droplet, the rapid transfer of carbon from the interior of the molten droplet to the surface is necessary. It was confirmed that the strong convection flow of the molten metal droplets satisfied the kinetic conditions of carbon in-situ in-flight deoxidation. The oxygen content in the APS-sprayed FeAl coatings increased with the increase of the spray distance. In contrast, the oxygen content in the APS-sprayed FeAl / 2.5C coatings decreased from 1.01 wt.% to 0.48 wt.% as the spray distance increased from 70 mm to 150 mm. This was accompanied by the decrease in carbon content from 1.41 wt.% to 0.31 wt.%, indicating the effective protection of Fe and Al from oxidation by the carbon in the droplet. Compared with the oxygen content of 3.67 wt.% in traditional FeAl coating, the oxygen content of the FeAl / 2.5C coatings was reduced to less than 0.5 wt.%. Considering that the carbon content of the coatings decreased as the spray distance increased, the results confirm that the in-flight oxidation of Fe and Al was suppressed by the preferential sacrificial oxidation of carbon in the molten droplets. Thus, the oxide in the FeAl / 2.5C coatings was mainly attributed to post-deposition oxidation. Moreover, the FeAl droplet reached the temperature to realize the spread-fusing self-metallurgical bonding effect for FeAl splats. The coatings exhibited a dense microstructure with an apparent porosity of less than 0.5%. The adhesive bonding strength of the prepared coatings exceeded 59.2 MPa owing to metallurgical bonding. The hardness of the coatings reached 590 HV0. 3, which was approximately twice that of traditional FeAl coatings. This was attributed to the reinforcement provided by the Fe3AlCx cementite phase resulting from the residual carbon in the coating.

Influence of FeCrAl Content on Microstructure and Bonding Strength of Plasma-Sprayed FeCrAl/Al2O3 Coatings

Microstructure and wear resistance of FeAl/Al 2 O 3 intermetallic composite coating prepared by atmospheric plasma spraying

Dielectric and Microwave Absorption Properties of Plasma Sprayed Cr/Al2o3 Composite Coatings

Plasma Sprayed Al2O3/FeCrAl Composite Coatings for Electromagnetic Wave Absorption Application

Microstructure and Properties of Al2O3-13wt.%TiO2-Reinforced CoCrFeMnNi High-Entropy Alloy Composite Coatings Prepared by Plasma Spraying

Microstructure, formation mechanism and properties of plasma-sprayed Cr7C3—CrSi2—Al2O3 coatings

Microstructure of plasma-sprayed Al2O3-ZrO 2 composite coatings

Optimizing of Hardness, Microstructure and Adhesive Strength of Plasma-Sprayed FeSiAl Coatings Using Orthogonal Analysis

Microstructure and Dielectric Properties of Plasma Sprayed Fe/Al_2O_3 Coatings

Effect of NiCrAlY Content on Mechanical and Dielectric Properties of NiCrAlY/Al2O3 Composite Coatings

Effects of plasma-sprayed NiCrAl/ZrO2 intermediate on the combination ability of coatings

Characterization of the Near-Eutectic Al2O3–40 Wt% ZrO2Composite Coating Fabricated by Atmospheric Plasma Spray. Part II: Microstructure and Mechanical Properties of Nanocomposite Coating

Effect of Critical Plasma Spray Parameter on Complex Permittivity and Microstructure by Plasma Spraying Cr/Al2o3 Coatings

Preparation Nanostructured FeAl2O4-Al2O3-Fe Composite Coating by SHS Plasma Spraying Technology

Influence of Plasma-Sprayed NiCrAl/ZrO_2 Intermediate on Adhesion of FeCrAl/γ-Al_2O_3

Mechanical and dielectric properties of Ni/Al 2O 3 composite coatings prepared by the axial plasma spraying

Fundamental understanding on the microstructure and corrosion resistance of Cr-(Cr, Al)2O3 composite coatings in-situ synthetized by reactive plasma spraying

Characterization of the Near-Eutectic Al<sub>2</sub>O<sub>3</sub>–40 wt% ZrO<sub>2</sub>Composite Coating Fabricated by Atmospheric Plasma Spray. Part II: Microstructure and Mechanical Properties of Nanocomposite Coating

Microwave absorption properties and complex permittivity of Fe/FeAl2O4 coatings deposited by reactive plasma spraying Al/Fe2O3 powders

Microstructure and Properties of Cold-Sprayed Al- X %al 2 O 3 Composite Coatings on LA43M Mg-Li Alloy

Mechanism of Suppressing Oxidation of FeAl Molten Droplet by Adding C to Powder and Its Effect on Microstructure and Properties of Plasma-sprayed Coating