Abstract:With the increasing diameter of deep-water bored piles, the risk of buckling deformation of super-large-diameter steel casings (SLDSC) during the dynamic impact driving process has increased dramatically. However, the risk factors involved in this process are yet to be ascertained. This study is based on the Xihoumen Rail-Road Bridge project, in which the steel casing used in the pile foundation has a design diameter of 6.8 m. LS-DYNA simulation software was used for numerical modelling. The influences of factors such as the casing wall thickness, hammering output energy, and the initial defect ovality were considered. The stress response, displacement depth (z-displacement), and buckling characteristics of SLDSC under axial impact load were studied. The reliability of the numerical modelling was also verified. The results show that for thin walls, the generated axial stress is great, and it is likely that buckling deformation can occur, thereby making it more difficult to drive the SLDSC to the designed depth. Relatively small hammering energy is insufficient to drive the SLDSC to the desired depth. As the hammering energy continues to increase, the increasing rate of z-displacement drops, and it is more likely to trigger non-axisymmetric buckling and curling of the SLDSC. For great initial defect ovality, the non-axisymmetric axial critical stress is small and is likely to trigger deformation accidents of the SLDSC, in which the buckling characteristics develops along the initial defect. Finally, for SLDSC used in relevant projects, it is recommended to have a wall thickness of 74–76 mm and hammering output energy of 1800–2000 KJ to control the ovality below 30 mm during manufacturing and transportation. The research results can provide a theoretical basis for the reasonable determination of wall thicknesses for SLDSC, the usage and debugging of special hammering equipment, and the control of defects during the manufacturing and transportation processes, thereby reducing the risks of buckling and deformation accidents during the axial impact driving process.

Buckling Analysis of Steel Cylinder in Super Long Bored Piles Construction

Theoretical Analysis of Longitudinal Vertical Displacement of Subway Tunnels Caused by the Construction of Steel Casings for Bridge Piles

Model Tests on the Bearing Capacity of Precast Open-Ended Micro Pipe Piles in Soft Soil

STUDY ON VERTICAL BEARING CAPACITY OF LARGE-DIAMETER CAST-IN-SITU THIN-WALL TUBULAR PILE

Model tests on the bearing capacity of precast oxen-ended micro pipe plies in sort soil

3-D Numerical Simulation for Large-Diameter Cast-In-Situ Tubular Pile

3-D Numerical Simulation for Large-Diameter Cast-<i>In Situ</i> Tubular Pile

Experimental Analysis of Bearing Capacity of Cast-in-place Tubular Pile

Seismic Behavior of Cft Column and Steel Pile Footings

Model Tests on Elevated Piles Subjected to Lateral Static and Impact Loading

Experimental Study on Bearing Capacity Behavior of Deep Large Diameter Cast-in-place Belled Pile

Analysis of Axial Load-Transfer of Large-Diameter Cast-in-situ Tubular Pile

Study on Axial Bearing Properties of Cast-in-place Concrete Thin-Wall Tubular Piles

Investigation of the Tensile Properties of High-Strength Bolted Joints in Static Drill Rooted Nodular Piles

Studies on Bearing Characteristic of Open-Ended and Close-Ended Pipe Piles under High-Speed Railway Loadings

Global Buckling of S35657 Austenitic Stainless Steel Welded Box- and I-section Long Columns under Axial Compression

Dynamic response of super-large-diameter steel casing under axial impact load

Theoretical analysis of dynamic performance of concrete-filled steel tube pile under vertical load

CONSTRUCTION TECHNOLOGY AND PILE QUALITY ANALYSIS OF SUPER-LONG ROCK-SOCKETED PILE CROSSING A HUGE-THICK GRAVEL LAYER

Large tonnage tests on super-long piles in soft soil area

Investigation of Analytical Behavior of Concrete Filled Steel Tubular (CFST) Offshore Rock-Socketed Pile under Lateral Load