Abstract:A large amount of air is drawn into the high-temperature plasma jet during the atmospheric plasma spraying (APS) process because it operates in an atmospheric environment, thus oxidizing metal-spray particles. The oxide inclusion resulting from in-flight droplet oxidation inhibits the metallurgical bonding between lamellae in the coating, which limits the applications of plasma-sprayed metal coatings. In this study, a novel approach to create oxide-free molten droplets is proposed by adding B to the CuNi powder to achieve sacrificial oxidation of B in the high-temperature droplet and protect the alloy elements from oxidation. Two powders of CuNi2B and CuNi4B were prepared to deposit the coatings via APS. The effect of B content and spray distance on the microstructure, as well as the O content of CuNi coating, was studied using methods such as SEM, EDS, XRD, and inductively coupled plasma-optical emission spectrum (ICP-CES). The results show that the droplet can be heated to more than 1900 degrees C, and the introduction of B in the powder can inhibit the oxidation of alloy elements in the high-temperature droplet during flight, thus reducing the oxygen in the CuNi coating. Moreover, the deoxidizing effect is affected by the B content of the droplet. Using 4%B CuNi alloy powder and increasing spray distance, the oxide in the coating is reduced. The oxygen in the coating is introduced via oxidation after droplet deposition, and the oxygen content of the coating prepared using the optimized spraying process is reduced to 0.43%, which is considerably lower than 3.5% of CuNiIn coating. An increase in the spray distance and a reduction in B content of CuNi powder, which contains 1.83%B, to 0.5% is insufficient to inhibit the oxidation of the alloying elements of the in-flight particles. The result yields a critical B content of approximately 0.5% for high-temperature droplet oxidation protection. The increase in the B content decreases the melting point, as well as the oxidation of the alloy, thus enhancing the metallurgical bonding between CuNi particles and improving the compactness of the coating. In addition, with the increase in the B content of the coating through the powder composition design and process parameters control from 0.26% to 3.61%, the microhardness of CuNi coating increases from 151 HV0.2 to 457 HV0.2.

The Oxidation Resistance of Cu-Ag Alloy Nanopowders Prepared by Induction Plasma Technology

A Catalytic Oxidation Approach to Coat Copper Powder with Polyaniline

Preparation of Oxidation-Resistant Ag-Cu Alloy Nanoparticles by Polyol Method for Electronic Packaging

Fabrication Of Fully Covered Cu-Ag Core-Shell Nanoparticles By Compound Method And Anti-Oxidation Performance

Controlling the Energy Release Behavior of Aluminum Nanoparticles As Metal Fuels by Atomic Layer Deposited Copper Oxide Nanocoatings

Oxide Cleaning Effect of In-Flight CuNi Droplet During Atmospheric Plasma Spraying by B Addition

Growth of 3-D Flower/Grass-Like Metal Oxide Nanoarchitectures Based on Catalyst-Assisted Oxidation Method

Influences of Tin Oxide Surface Modification on the Morphology and Performance of Sintered Ag/SnO2 Composite Powders

Electrodeposition of AgCuO2 Nanoplates

<i>In Situ</i> Synthesis and Oxidation Behavior of Ti-Al-Ag Ternary Coatings

Rapid preparation of micro/nano porous Cu/Cu 2 O particles through dealloying of powder sintered Cu-Al alloy

Novel Cu@Ag Micro/Nanoparticle Hybrid Paste and Its Rapid Sintering Technique via Electromagnetic Induction for High-Power Electronics

Oxidation behavior and mechanism of Ag-9.8Sn-1.3Bi-0.4Cu alloy powders in different oxidant

Influence of the Ag Content on the Natural and Thermal Induced Oxidation of Cu Thin Films

Oxidation-Induced Atom Diffusion and Surface Restructuring in Faceted Ternary Pt–Cu–Ni Nanoparticles

Fabrication and performance of silver coated copper powder

Magical Oxygen: Tuning Cu&Ag Nanoporous Membrane into Nanoporous (cu&ag)@ag Core-Shell Alloy

A Novel Antioxidation Treatment Method for Micron/Nano Copper Materials in Semiconduct Field

Mechanistic Insights into Plasma Oxidation of Ag Nanofilms: Experimental and Theoretical Studies

Fabricating Nanometer Cu/Al Composite Powder by Electroless Copper Plating

Influence of oxidant and sample state on oxides distribution of Ag-4.93Sn-3.56In alloy powders