Abstract:Due to the high modulus, high strength, low density, excellent wear resistance and good neutron absorption, the boron carbide (B4C) particle reinforced aluminum (Al) matrix composites have been widely applied in the aerospace, weaponry, transportation and neutron shielding fields. In response to the increasing requirement of better strength -ductility matching of B4C/Al composites, introducing a nano-scale reinforcement into the B4C/Al composites becomes an attractive research focus. In this work, the SiC nanowires were ball-milled with Al powders, and then the SiC/Al composite powders were mixed with B4C microparticles. Thus, the 15vol. % B4C/SiC/Al composites with different volume fractions of SiC nanowires were fabricated by hot-pressing sintering and hot extrusion. B4C microparticles and SiC nanowires are uniformly dispersed in the B4C/SiC/Al composites, while the introduced SiC nanowires effectively decrease the Al matrix grain sizes. B4C/SiC/Al composites produce the better strength-ductility matching than that of B4C/Al composites, while the 15vol. % B4C/SiC/Al composite with 1vol. % SiC nanowires achieved the best strength-ductility matching. It generates the 281.7 ± 2.7 MPa in yield strength, 351.2 ± 0.1 MPa in ultimate tensile strength and 5.9 ± 0.7% in failure elongation, which are increased by 18.2%, 15.1% and 13.5% compared to the B4C/Al composites. Uniformly dispersed B4C microparticles and SiC nanowires largely block the dislocation motions and improve the dislocation storage capacity, which results in a more significant hetero-deformation induced (HDI) hardening effect in the B4C/SiC/Al composites. Moreover, the B4C/Al interfacial transition regions with the added SiC nanowires becomes stronger, which can enhance the load transfer efficiency of the B4C/Al interfaces as a result of the existing dislocation hardening zones. In conclusion, it is a good strategy to combine the synergistic strengthening effect of micro-scale and nano-scale reinforcements in the metal matrix composites.

In-Situ Carbon Nanotube-Covered Silicon Carbide Particle Reinforced Aluminum Matrix Composites Fabricated by Powder Metallurgy

Micro-mechanical and tribological behavior of Al/SiC/B4C/CNT hybrid nanocomposite

Fabrication of high-content hybrid-reinforced Al nanocomposites by in-situ reaction of TiO 2 -decorated CNTs and matrix

Dual-nanoparticulate-reinforced aluminum matrix composite materials

Fabrication, microstructure characterization and mechanical properties of B4C microparticles and SiC nanowires hybrid reinforced aluminum matrix composites

Mechanical and Electrical Properties of Nano Al-Matrix Composites Reinforced with SiC and Prepared by Powder Metallurgy

Synergistic Strengthening of Aluminum Matrix Composites Reinforced by SiC Nanoparticles and Carbon Fibers

Microstructure And Mechanical Properties Of Al-Sic Nanocomposites Synthesized By Surface-Modified Aluminium Powder

Microstructure Evolution and Mechanical Behaviors of SiCp/CNTs Hybrid Reinforced Al-Si-Cu-Mg Composite by Semi-solid Stir Casting

Enhanced Combination of Strength and Ductility in Ultrafine-Grained Aluminum Composites Reinforced with High Content Intragranular Nanoparticles

Mechanical and thermal expansion behavior of hybrid aluminum matrix composites reinforced with SiC particles and short carbon fibers

In-situ synthesis and microstructural evolution of a SiC reinforced Al-50Si composite exhibiting exceptional thermal properties

Effects of Silicon Carbide and Tungsten Carbide in Aluminium Metal Matrix Composites

Effectively enhanced strength by interfacial reactions in in-situ carbon reinforced Al matrix composites

Study on the Properties of Carbon Nanotube (CNTs) Reinforced AlSi10Mg Composites Fabricated by Powder Metallurgy

Synthesis of carbon nanotube reinforced Al matrix composite coatings via cold spray deposition

Preparation and Properties of Nano-sized SiC Particles Reinforced ADC12 Aluminum Matrix Composites

Preparation of in situ TiC@TiN core–shell and Ti2N–Al4C3 nanoparticles and their effects on Al–Zn–Mg–Cu alloy

The enhanced mechanical properties and strain-hardening capability of CNT/Al composites achieved by heterogeneous micro-laminated architecture

Preparation, Microstructure and Mechanical Properties of In-Situ TiC/Al–Si–Fe Aluminum Matrix Composites

Untrasonic-Assisted Fabrication of SiC Nanoparticles Reinforced Aluminum Matrix Composites