Abstract:The effect of cerium (Ce) on the solidification microstructure of Cr4Mo4V bearing steel was investigated via a combined experimental and theoretical method. With a trace amount (0.056 wt%) of Ce addition, the coarse columnar grains in as-cast microstructure transform into equiaxed ones, and the average diameter is reduced from 56 to 27 μm. The network-like and bulky primary MC and M 2 C carbides at the interdendritic regions become disconnected and refined, and their volume percentage decreases from 4.15 vol% to 2.1 vol%. Ce-inclusions acting as heterogeneous nucleation agents of prior-austenite grains and Ce atoms segregating at grain boundaries, both contribute to the refinement of grains. Thermodynamic calculations reveal that primary carbides are precipitated after γ -austenite forms near the end of the solidification process. The modification of primary carbides in size and amount is mainly attributed to the isolated remaining melt separated by refined γ -austenite grains in which the nucleation of carbides is promoted, while the growth is restrained owing to the less segregation of alloying elements. Graphical abstract The grains and primary carbides of Cr4Mo4V bearing steel was refined with the proper addition of Ce. We find that Ce-inclusions acting as heterogeneous nucleation agents of prior-austenite grains and Ce atoms segregating at grain boundaries, both contributed to the refinement of grains. The modification of primary carbides in size and amount is mainly attributed to the isolated remaining melt separated by refined γ -austenite grains in which the nucleation of carbides is promoted, while the growth is restrained owing to the less segregation of alloying elements. Download : Download high-res image (744KB) Download : Download full-size image

Microstructure and Compound Developed from Ce-As-Fe System at High Temperature

Structure and Property Modulations of 13cr Stainless Steel Through Microgravity Solidification and Minor Ce Addition

Achieving Enhanced Strength Retention at Elevated Temperatures in Ultrafine-Fibrous Interconnected Al-Ce-Ni Eutectic Alloy Solidified under Super-Gravity Field

Effect of Cerium Addition on Microstructure and Mechanical Properties of As-Cast High Grade Knives Steel

Refining Mechanism and Elevated-Temperature Mechanical Properties of Al-Ce Alloys Solidified under Super Gravity Field

The Compositional Range of Amorphous Phase Formation and Thermal Stability of Al90−xFe5Ni5Cex

Influence of cerium treatment on inclusion modification and as-cast microstructure of high-strength low-alloy steel

Uncovering the effects of Ce and superheat temperature on Fe-rich intermetallic and microporosity formation in aluminum alloy

Thermal Stability of Al2Si2Ce Compound in Sr/Ce-modified Cast and Heat-Treated A356 Al-alloys

Microstructure and Mechanical Properties of Al-Cu-Ce Alloy

Effect of the addition of cerium on the microstructure evolution and thermal expansion properties of cast Al-Cu-Fe alloy

Evolutions of Microstructure by Cerium Treatment in As‐Cast M2 High‐Speed Steel

Elevated temperature microstructural stability in Al-7Cu-0.5Mn-0.2Zr alloys through Ce addition: Enhanced coherent interfacial stability of cu-rich θ'/α-Al interface

Effects of Cerium Micro-Alloying on Microstructural Evolution and Dispersion Strengthening in Al-Yb-Er-Zr Alloy

Microstructure Evolution of a Reactor Pressure Vessel Steel During High-Temperature Tempering

Cerium refinement of grains and primary carbides during solidification of Cr4Mo4V bearing steel

The effect of M (M = Ce, Zr, Ce-Zr) on rolling microstructure and mechanical properties of FH40

Influence of cerium on microstructures and mechanical properties of Al-Zn-Mg-Cu alloys

Effect of Rare Earth Ce Addition on the Microstructure and Mechanical Properties of an Al–Cu–Mg–Ag Alloy

Influences of Ce Addition on the Microstructures and Mechanical Properties of 2519a Aluminum Alloy Plate

Investigation of the 600 °C Isothermal Section of the Fe–Al–Ce Ternary System