Abstract:Based on the results of current research and experiments, clock 135° hot rolling has been widely considered to be the preferred method in target rolling. However, it has been found that the process parameters are of vital importance during the rolling. Therefore, this work focuses mainly on the investigation of the effects of the roll speed ratio and offset distance on the microstructure evolution of a pure aluminum (Al) target under clock 135° collaborative hot rolling. Taking the ultra-thick pure Al metal circular billet as a research object, firstly, the evolutionary behavior of the effective strain (ES) and grain refinement for a rolled piece under the clock counterclockwise 135° synchronous and asynchronous (the speed ratios between rollers are set to be 1:1.05, 1:1.1, 1:1.2, respectively) rolling modes has been comparatively studied based on numerical simulation by DEFORM-3D software. It has been shown that a large ES value of 5.835 mm/mm is obtained in the lower surface layer by counterclockwise 135° asynchronous rolling with a roll–speed ratio of 1:1.2. Meanwhile, the average grain size below 80 μm accounts for ~61.8% of the total grains. These results demonstrate that the clock counterclockwise 135° asynchronous rolling method with a roll speed ratio of 1:1.2 should be an ideal strategy in obtaining finer grains. Unfortunately, nevertheless, the maximum degree of the bad plate shape is generated after forging by clock asynchronous rolling with a speed ratio of 1:1.2. As a consequence, clock counterclockwise 135° snake rolling with a 30 mm offset distance was proposed on the basis of a rolling speed ratio of 1:1.2, which perfectly corrected the warping plate shape caused by clock asynchronous rolling. What is more important, the minimum damage value of 1.60 was achieved accordingly. Meanwhile, the ES value increased in the core of the plate for the clock counterclockwise 135° snake rolling with all of the four offset distances compared to clock synchronous rolling. This study should be significantly conducive to guidance on setting process parameters in the industrial production of hot rolling metal or alloy targets.

Effects of rolling parameters of snake hot rolling on strain distribution of aluminum alloy 7075

Microstructure, Texture Andmechanical Properties of Aa1060 Aluminum Plate Processed by Snake Rolling

Effect of rolling deformation and passes on microstructure and mechanical properties of 7075 aluminum alloy

The theoretical model of the effective strain establishment for the plate during the snake rolling

Research on Hot Rolling Process of 7075 Aluminum Alloy

Bending analysis and control of rolled plate during snake hot rolling

Effects of Process Parameters on Microstructure Evolution of Pure Aluminum Target under Clock 135° Collaborative Hot Rolling: A Simulation Study

Analysis of Temperature Asymmetry of Aluminum Alloy Thick Plate During Snake Hot Rolling

Effect of Rolling Strain on Microstructure and Tensile Properties of Dual-Phase Mg–8Li–3Al–2Zn–0.5Y Alloy

Calculation and analysis of rolling force during aluminum alloy thick plate snake/gradient temperature rolling with different roll diameters

The central strain analytical modeling and analysis for the plate rolling process

Effects Of Rolling Process On Microstructure And Mechanical Property Of 7050 Aluminum Alloy

Effect of Deformation Mode on Grain Characteristics and Strength–Toughness of Al-Zn-Mg-Cu Alloy

Effect of Heat Treatment on the Microstructure and Properties of High Strain Rate Rolled 7050 Aluminum Alloy

Microstructural Evolution and Mechanical Properties in Zr705 During the Rolling Process

Effects of rolling processing on the microstructures, mechanical properties and strain softening behavior of biodegradable Zn-0.06 Mg alloy

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys

Effect of Asymmetric Cross Rolling on Microstructure and Mechanical Properties of AZ31 Magnesium Alloy

Influence of Hot Rolling Process on Microstructures of 7055 Aluminum Alloy Thick Plate

Effect of Pre-Deformation of Rolling Combined with Stretching on Stress Corrosion of Aluminum Alloy 2519A Plate

Effects of Rolling Deformation on Precipitation Behavior and Mechanical Properties of Al–Zn–Mg–Cu Alloy