Abstract:High temperature helium gas will provide a thermal efficiency greater than 40%, even using a conventional steam turbine. In addition, helium gas will not react chemically with blanket materials, and surrounding air and water. Tritium will be easily extracted from the coolant too. Thus, it is one of the most attractive coolants for a fusion power reactor, from the economical, safety and environmental points of view. However, a large volumetric flow rate is required owing to the small heat capacity when the pressure is not extremely high. This requires a larger reactor size, larger circulating power and more penetrations, which may increase radiation streaming. A relatively low heat transfer coefficient makes it difficult to apply to a component subjected to a high heat load, such as a divertor plate. We suggest in this study, a helium-solid suspension flow as coolant, to increase the heat capacity and heat transfer coefficient. A gas pressure of 5 MPa, and inlet and outlet temperatures of 400°C and 700°C were chosen. There are few candidates for the structural material which can be used at temperatures higher than 900°C. We have proposed an intermetallic compound of titanium aluminide (TiAl) as candidate structural material of the blanket. Although the database for TiA1 is incomplete, it has high strength and ductility at the operation temperature. Using TiA1, radioactive waste management will be mitigated, since its activity will decrease rapidly. The elongation at room temperature, which is only a few per cent, will be improved through research and development not only in fusion but also in other industrial fields. In this study, spherical pebbles of lithium oxide and small blocks of beryllium were chosen as the breeder and neutron multiplier. Manganese blocks were installed to enhance energy multiplication. A tritium breeding ratio of 1.38 and energy multiplication ratio of 1.35 were obtained with the blanket. The net plant efficiency exceeds 40%, including the circulating power. The peak surface heat flux on the divertor plate was decreased with gas puffing including an impurity near the striking point. In spite of this, the expected peak heat flux was still several MW m−2 from the result of numerical calculation of the edge plasma. To remove so high a heat load, an impinging helium-solid suspension jet was applied to the high heat flux region of the divertor plate. Molybdenum alloy was used as the structural material in this region to keep the surface temperature and thermal stress lower than the design limits. TiAl was used as the structural material of other regions in the divertor chamber. To prevent excessive sputtering erosion, the electron temperature in the divertor plasma must be kept lower than 20 eV.

Neutronic Analysis of Ifmif High Flux Test Module for High Temperature Irradiation

Progress of High Heat Flux Component Manufacture and Heat Load Experiments in China

Monitoring for Actinide Neutron Emissions From Spent Nuclear Fuel Under Extreme Gamma Fields Using Centrifugally Tensioned Metastable Fluid Detector Sensor Technology

Neutronic assessment of the IFMIF-DONES HFTM specimen stack distribution

Neutronic analysis of IFMIF-DONES test cell cooling system

Concept of Staged Approach for International Fusion Materials Irradiation Facility

Irradiation Performance and Modeling of Htr-10 Coated Fuel Particles

Irradiation Testing of Matrix Material for Spherical HTR-10 Fuel Elements

Design study of helium-solid suspension cooled blanket and divertor plate for a tokamak power reactor

Effects of HFIR neutron irradiation on fracture toughness properties of standard and Ni-doped F82H

Comparative study of ITER conform tungsten grades exposed to high heat flux and neutron irradiation damage

Irradiation test of diagnostic components for ITER application in the Japan Materials Testing Reactor

Development of irradiation tolerant tungsten alloys for high temperature nuclear applications

Source Term Analysis and Sorting Scheme in Post-Irradiation Spherical Pyrometric Elements

Thermomechanical Properties of Neutron Irradiated Al3Hf-Al Thermal Neutron Absorber Materials

R&D OF SICF/SIC COMPOSITE FOR FUSION REACTOR MATERIAL

Engineering design status of IFMIF-DONES High Energy Beam Transport line and Beam Dump system inside the TIR and RIZ

HTR-PM Fuel Pebble Irradiation Qualification in the High Flux Reactor in Petten

Helium ion irradiation-induced damage of powder metallurgy-hot isostatic pressed Ni-based alloy GH3535 for molten salt reactor applications

Microstructure response of ferritic/martensitic steel HT9 after neutron irradiation: Effect of temperature

Thermal-fluid-structure Coupling Analysis for Plate-Type Fuel Assembly under Irradiation. Part-I Numerical Methodology