Abstract:Tristructural-isotropic (TRISO) fuel particles have long been widely used in high temperature gas-cooled reactors (HTGR), where their high temperature mechanical integrity and ability to retain fission products even in the accident conditions are the critical safety issues. In the present work, TRISO particles were subjected to ultra-high temperature thermal treatments at 1900, 2000, and 2200 degrees C, respectively, which were much higher than the projected accident temperature (1620 degrees C). Phase compositions and microstructures of the samples before and after thermal treatments were studied by X-ray diffraction (XRD), Raman spectroscopy, and Scanning Electron Microscopy (SEM). Nano hardness and Young's modulus of the SiC layer in TRISO particles were studied by nano indentation technique, and crushing strength of the TRISO particles was evaluated by mechanical crush tests. The results show that, there were no obvious temperature effects on phase composition and microstructure, except for SiC layer in the sample thermal treated at 2200 degrees C, in which many pores caused by SiC decomposition were observed. The nano hardness and Young's modulus values of SiC layer in the as-received and thermally treated TRISO particles were similar within the experimental error. On the other hand, the crushing strength of the thermally treated TRISO particles decreased greatly as compared with the as-received particles, but the crack propagation mode changed from through-the-particle to deflection inside the buffer PyC layer or between buffer PyC and inner PyC (IPyC) layers. The change of crack propagation mode could probably due to the shrinkage of PyC layers due to anisotropy at high temperature and ordering of graphitization of IPyC layers, which probably weakened the interfacial bonding between the IPyC and the buffer PyC layers. The results of this study provide a database reference for the performance of TRISO particles under ultra-high temperature operation and even accident conditions. (C) 2022 Elsevier B.V. All rights reserved.

An Improved Design of TRISO Particle with Porous SiC Inner Layer by Fluidized Bed-Chemical Vapor Deposition

Preparation of Silicon Carbide Coating Layer by Fluidized Bed Chemical Vapor Deposition Using a Halogen-Free Precursor

Design and preparation of SiC based novel coated fuel particle

Preparation and Performance of Fully Ceramic Fuel Element Using Silicon Carbide As Coating Layers

Study of SiC layer with fine grains in HTGR coated fuel particles

Preparation of ZrC Coating in TRISO Fuel Particles by Precise Transportation of Solid Precursor and Its Microstructure Evolution

Ultra-high temperature microstructural changes of SiC layers in TRISO particles

A New Design of Composite Fuel with Zr-coated TRISO Particles Dispersed in Metal Matrix

Preparation of the Coated Nuclear Fuel Particle Using the Fluidized Bed-chemical Vapor Deposition (FB-CVD) Method

Effects of Stoichiometry and High-Temperature Annealing on Zirconium Carbide Coating Layer in TRISO Particles

Properties of SiC Coated Layer for HTGR Fuel Particles

High Temperature Oxidation Behavior of SiC Coating in TRISO Coated Particles

Fully Ceramic Microencapsulated Fuels with High TRISO Particles Loading Capacity Fabricated by Gel-Casting

Oxidation mechanism of SiC coated layer in air atmosphere at 1400°C

Three-Dimensional Measurement of TRISO Coated Particle Using Micro Computed Tomography

Effect of Ultra-High Temperature Treatment on Microstructures and Mechanical Properties of TRISO Particles

The Study of Irradiation-Induced Failure Behavior for the TRISO-coated Fuel Particle in HTGR

Preparation of SiC Composite Coating on the Surface of Graphite Spheres in VHTR

Irradiation-Thermal-Mechanical Coupling Behaviors of a Typical TRISO/SiC Fuel Element Based on Actual Distribution

Preparation and High Temperature Performance of NbC Layer in TRISO Particles

The Research Progress of Zrc Coating Layer of Fuel Particles for Htgr at Home and Abroad