Abstract:An equiatomic CoCrFeMnNi high-entropy alloy, which crystallizes in the face-centered cubic (fcc) crystal structure, was produced by arc melting and drop casting. The drop-cast ingots were homogenized, cold rolled and recrystallized to obtain single-phase microstructures with three different grain sizes in the range 4–160μm. Quasi-static tensile tests at an engineering strain rate of 10−3s−1 were then performed at temperatures between 77 and 1073K. Yield strength, ultimate tensile strength and elongation to fracture all increased with decreasing temperature. During the initial stages of plasticity (up to ∼2% strain), deformation occurs by planar dislocation glide on the normal fcc slip system, {111}〈110〉, at all the temperatures and grain sizes investigated. Undissociated 1/2〈110〉 dislocations were observed, as were numerous stacking faults, which imply the dissociation of several of these dislocations into 1/6〈112〉 Shockley partials. At later stages (∼20% strain), nanoscale deformation twins were observed after interrupted tests at 77K, but not in specimens tested at room temperature, where plasticity occurred exclusively by the aforementioned dislocations which organized into cells. Deformation twinning, by continually introducing new interfaces and decreasing the mean free path of dislocations during tensile testing (“dynamic Hall–Petch”), produces a high degree of work hardening and a significant increase in the ultimate tensile strength. This increased work hardening prevents the early onset of necking instability and is a reason for the enhanced ductility observed at 77K. A second reason is that twinning can provide an additional deformation mode to accommodate plasticity. However, twinning cannot explain the increase in yield strength with decreasing temperature in our high-entropy alloy since it was not observed in the early stages of plastic deformation. Since strong temperature dependencies of yield strength are also seen in binary fcc solid solution alloys, it may be an inherent solute effect, which needs further study.

The Evolution of Internal Stress and Dislocation During Tensile Deformation in a 9cr Ferritic/martensitic (F/M) ODS Steel Investigated by High-Energy X-rays

Temperature Effects on Deformation Substructures and Mechanisms of a Ni-based Single Crystal Superalloy

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

Microstructures and Tensile Properties of 9Cr-F/M Steel at Elevated Temperatures

Influence of temperature on ductility of nano-ODS steel prepared by low-energy mechanical alloying

Temperature-dependent mechanical properties of an austenitic-ferritic stainless steel studied by in situ tensile loading in a scanning electron microscope (SEM)

Dislocation Hardening in a New Manufacturing Route of Ferritic Oxide Dispersion-Strengthened Fe-14Cr Cladding Tube

An in situ ambient and cryogenic transmission electron microscopy study of the effects of temperature on dislocation behavior in CrCoNi-based high-entropy alloys with low stacking-fault energy

Temperature and Crystalline Orientation-Dependent Plastic Deformation of FeNiCrCoMn High-Entropy Alloy by Molecular Dynamics Simulation

Tensile deformation dominated by matrix dislocations at intermediate temperatures revealed using in-situ EBSD in superalloys

Deformation Mechanisms of Al0.1CoCrFeNi at Elevated Temperatures

Microstructural stability of a 9Cr oxide dispersion strengthened alloy under thermal aging at high temperatures

Constitutive Descriptions and Restoration Mechanisms of a Fe-17Cr Alloy during Deformation at Temperatures of 700–1000 °C

The influences of temperature and microstructure on the tensile properties of a CoCrFeMnNi high-entropy alloy

Unveiling the relationship between dislocation structure evolution and strain hardening behavior of S32654 super-austenitic stainless steel

Temperature Dependence of Deformation Behaviors in High Manganese Austenitic Steel for Cryogenic Applications

Diffusional and displacive transformations in interstitial-free steel within the scope of a critical assessment of the mechanical property

Strain-Rate-Dependent Deformation Behavior of Ti29Zr24Nb23Hf24 High Entropy Alloys at Elevated and Room Temperature

Mechanism of Fatigue-Life Extension Due to Dynamic Strain Aging in Low-Carbon Steel at High Temperature

Investigating the microstructural evolution during deformation of laser additive manufactured Ti–6Al–4V at 400 °C using in-situ EBSD

Microstructure evolution and void swelling of ODS ferritic/martensitic steel under high damage irradiation