Abstract:(Zr62Cu15.4Ni12.6) (x = 6–12) in situ glassy composites containing uniformly distributed Ta-rich particles were prepared by arc-melting and copper mould casting. The results show that addition of 6–10 at.% Ta to Zr62Cu15.4Ni12.6Al10 results in dissolution of 2.4 to 4.6 at.% Ta in the glassy matrix, which promotes glass-forming ability, and the remaining Ta precipitates out as body-centered cubic (BCC) Ta-rich particles dispersed on the glassy matrix. The critical diameters for the composites with 6, 8, and 10 at.% Ta are 7, 7, and 6 mm, respectively. At 12 at.% Ta addition, the glass-forming ability is dramatically reduced because of the precipitation of secondary dendritic Ta-rich particles and other nanocrystallites from melts during copper mould casting. Also, owing to the solid-liquid reaction during induction heating, some Ta-rich particles formed in the master alloys will redissolve into the glassy matrix, resulting in a smaller volume fraction of Ta-rich particles in the as-cast glassy rods than that of the corresponding ingots. The glassy matrix composites exhibit enhanced plastic strain of about 7.5 to 22.5% at room temperature. The optimum Ta content in the glassy alloys is determined to be 10 at.%, which corresponds to the highest ultimate stress of 2220 MPa and the largest plastic strain of 22.5%. The plastic strain increases with increasing volume fraction of in situ BCC Ta-rich particles. This is apparently ascribed to the impedance of Ta-rich particles to shear bands. Ta-rich particles seed the initiation of multiple shear bands and block the shear band propagation, leading to intensive multiplication and bifurcation of shear bands.

The Study on Interface and Property of TiNb/Zr-based Metallic Glassy Composite Fabricated by SPS

Toughening mechanism of Zr-based and Cu-based bulk metallic glasses composites by TiNb particle

Composition Dependence of the Microstructure and Mechanical Behavior of Ti–Zr–Cu–Pd–Sn–Nb Bulk Metallic Glass Composites

Synthesis and Property of Short Tungsten Fibre/zr-Based Metallic Glass Composite

Characterization of Interface Between the Particles in NiNbZrTiPt Metallic Glassy Matrix Composite Containing SiC Fabricated by Spark Plasma Sintering

Ti Particles Dispersed Ti-Based Metallic Glass Matrix Composite Prepared by Spark Plasma Sintering

Correlation Between the Enhanced Plasticity of Glassy Matrix Composites and the Intrinsic Mechanical Property of Reinforcement

Enhanced Mechanical Properties by Cyclic Compression in TiNb/Zr-Based Metallic Glassy Composite

The Effect of Matrix Fracture Toughness on the Plastic Deformation of the Metallic Glassy Composite

Martensitic Transformation and Plastic Deformation of TiCuNiZr-Based Bulk Metallic Glass Composites

Relationship Between the Reinforcement Size and Mechanical Properties of Zr-Based Glassy Matrix Composites

High Tensile Plasticity and Strength of a CuZr-based Bulk Metallic Glass Composite

Zr-Cu-Ni-Al-Ta Glassy Matrix Composites with Enhanced Plasticity

Improved Tensile Ductility by Severe Plastic Deformation for Nano-Structured Metallic Glass.

Effects of Crystallization Fractions on Mechanical Properties of Zr-based Metallic Glass Matrix Composites

Effect of Chemical Composition on the Thermoplastic Formability and Nanoindentation of Ti-Based Bulk Metallic Glasses

Mechanical and corrosion properties of Ti-Ni-Cu-Zr metallic glass matrix composites

Fabrication of Ni<sub>52.5</sub>Nb<sub>10</sub>Zr<sub>15</sub>Ti<sub>15</sub>Pt<sub>7.5</sub> Bulk Metallic Glassy Matrix Composite Containing Dispersed ZrO<sub>2</sub> Particulates by Spark Plasma Sintering

Fabrication of ZrCuAlNi Metallic Glassy Matrix Composite Containing ZrO2 Particles by Spark Plasma Sintering Process

Microstructure and Mechanical Properties of Porous Zr55Cu30Al10Ni5 Bulk Metallic Glass Fabricated by Spark Plasma Sintering Process

Cu Particulates Dispersed Bulk Metallic Glass Composites with High Strength and High Electrical Conductivity Fabricated by Spark Plasma Sintering