Abstract:In this paper, 4.5 vol% TiBw/TAl5 composite with columnar network reinforced structure was prepared by pre-sintering and subsequent hot extrusion process. Pre-sintering was conducted at 1100 °C for 0.5 h, and billets were extruded with an extrusion ratio of 10: 1. The extrusion speed was 10 mm/s, and water cooling was adopted. An extrusion temperature range of 925–1100 °C (which covers the phase transition) was used to study the influence of the extrusion temperature on the microstructure evolution and its correlation with strengthening. The results showed that the extrusion temperature played a decisive role in the evolution of the matrix morphology. When the extrusion temperature increased from the (α + β) dual-phase region to the β single-phase region, the microstructure of the composite matrix was mainly composed of elongated α phase and recrystallized α phase. It gradually transformed into a lamellar structure from a high-temperature β phase. TiB whiskers continued to grow and coarsen. The corresponding texture also changed from 〈10−10〉 α//ED component in the dual-phase region to 〈0001〉α//ED and 〈10−11〉 α//ED mixed components, which were related to the high-temperature 〈101〉β//ED component in the β-phase region. Further performance analysis showed that the matrix strength was positively correlated with the content of the lamellar α phase, which increased with the extrusion temperature; however, the strengthening of TiB whiskers was affected by its growth and fragility and displayed a weakening trend. As a result, although the strength of the composite was always better than that of the matrix, its overall strength decreased upon increasing the extrusion temperature, showing the best performance when extruded at 925 °C. The stress of strengthening effect could be accurately estimated by the shear lag model.

Evolution of inhomogeneous reinforced structure in TiBw/Ti-6AL-4V composite prepared by pre-sintering and canned β extrusion

In Situ TiBw/Ti–6Al–4V Composites with Novel Reinforcement Architecture Fabricated by Reaction Hot Pressing

High Temperature Tensile Properties of in Situ TiBw/Ti6Al4V Composites with a Novel Network Reinforcement Architecture

Preparation of TiBw/Ti–6Al–4V Composite with an Inhomogeneous Reinforced Structure by a Canned Hot Extrusion Process

Room temperature tensile fracture characteristics of in situ TiBw/Ti6Al4V composites with a quasi-continuous network architecture

Superior tensile strength and microstructure evolution of TiB whisker reinforced Ti60 composites with network architecture after β extrusion

Effects of the Extrusion Temperature on the Microstructure and Mechanical Properties of TiBw/Ti6Al4V Composites Fabricated by Pre-Sintering and Canned Extrusion

Mechanisms Behind the Superplastic Behavior of As-Extruded Tibw/Ti6al4v Composites with A Network Architecture

Influence of Tibw Volume Fraction on Microstructure and High-Temperature Properties of in Situ Tibw/Ti6al4v Composites with Tibw Columnar Reinforced Structure Fabricated by Pre-Sintering and Canned Extrusion

Evolution of microstructural characteristic and tensile properties during preparation of TiB/Ti composite sheet

Research on the Inhomogeneity and Joint Interface of in Situ Oriented TiBw/TA15 Composites Fabricated by Vacuum Hot-Pressing Sintering and Canned Extrusion

Effects of pre-sintering on microstructure and properties of TiBw/Ti6Al4V composites fabricated by hot extrusion with steel cup

Effects of Heat Treatment on the Microstructure and Mechanical Properties of in Situ Inhomogeneous TiBw/Ti6Al4V Composite Fabricated by Pre–sintering and Canned Powder Extrusion

Microstructure Evolution and High-Temperature Tensile Behavior of the Powder Extruded 2.5 Vol% TiBw/TA15 Composites

Temperature influenced microstructure evolution and strengthening of 4.5 vol% TiBw/TA15 composites with columnar-reinforced structure fabricated by pre-sintering and hot extrusion

Microstructure and Properties of 3.5 Vol.% TiBw/Ti6Al4V Composite Tubes Fabricated by Hot-hydrostatic Extrusion

A TiB whisker-reinforced titanium matrix composite with controllable orientation: A novel method and superior strengthening effect

Effects of Extrusion and Heat Treatment on the Microstructure and Tensile Properties of in Situ TiBw/Ti6Al4V Composite with a Network Architecture

Modification of Microstructure and Tensile Property of TiBw/near-α Ti Composites by Tailoring TiBw Distribution and Heat Treatment

Microstructure and Mechanical Properties of 2.5 Vol. % TiBw/Ti6Al4V Composites Plates Fabricated by Hot-Hydrostatic Canned Extrusion

Significantly Enhanced Superplasticity of TiBw/near-α Ti Composite: Microstructure Tailoring and Deformation Mechanisms