Abstract:Mg-4.4Zn-0.3Zr-0.4Y (wt%) alloy ingots were prepared by two casting processes with different cooling methods: air cooling cast (AC cast) and water cooling cast (WC cast). Then, the two types of Mg-4.4Zn-0.3Zr-0.4Y alloy ingots were extruded under the same condition, and the effect of different cooling methods on microstructure and mechanical properties of the extruded alloy was studied. The results show that the cooling method of melt during cast processing has a great effect on microstructure and mechanical properties of the extruded alloy. Compared with AC cast alloy, the lamellar eutectic structure and dendrite cell size of WC cast alloy are significantly refined, while the formation of W-phase (Mg3Y2Zn3) is suppressed and the volume fraction of I-phase (Mg3YZn6) increases in WC cast alloy. After extrusion deformation, the WC cast Mg-4.4Zn-0.3Zr-0.4Y alloy has finer dynamically recrystallized grains, finer and more uniformly fragmented I-phase particles distributed in the matrix and grain boundaries, weakened {0002} basal texture intensity and increased {10 (1) over bar2} texture intensity compared with those of the extruded AC cast alloy. The yield strength and tensile strength of the extruded WC cast Mg-4.4Zn-0.3Zr-0.4Y alloy reach 297.0 and 327.3 MPa, which are increased by 46.4 and 21.4 MPa, respectively compared with those of the extruded AC cast alloy. The extruded WC cast Mg-4.4Zn-0.3Zr-0.4Y alloy shows an elongation of 14.8%, which is 4.7% improvement compared with that of the extruded AC cast alloy.

Effect of Grain Size on the Microstructure and Mechanical Properties of Mg-4Y-3Nd-0.5Zr Alloy

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

Microstructure and Mechanical Properties of Mg-Xy-1.5mm-0.4zr Alloys

Effects of Minor Y Addition on Microstructure and Mechanical Properties of Mg-Nd-Zn-Zr Alloy

Effect of Solution Temperature on Grain Size in A Mg-4y-3nd-3dy-0.5zr Alloy

Effect of cooling rate on microstructure and mechanical properties of Mg-9Gd-4Y-1Zn-1Al alloy

Effect of cooling rate on the microstructure and mechanical properties of sand-casting Mg-10Gd-3Y-0.5Zr magnesium alloy

Microstructure and Mechanical Properties of Extruded Mg-Zn-Nd-Y-Zr-Ca Alloy

Influence of Solidification Conditions on Mechanical Properties of Mg-10gd-3y-0.5zr Magnesium Alloy

The Effect of Casting Speed on Microstructure, Microsegregation, and Mechanical Properties of High-Strength Mg-Nd-Zn-Zr Alloy

Effects of Zr on Microstructure and Properties of MgZn5Nd3.5 Alloy

The microstructure, fracture mechanism and their correlation with the mechanical properties of as-cast Mg-Nd-Zn-Zr alloy under the effect of cooling rate

Effects Of Zn On Microstructure And Mechanical Properties Of As-Cast Mg-Y-Nd-Zr Alloys

Effects of Gd and Zr Additions on the Microstructures and High-Temperature Mechanical Behavior of Mg–Gd–Y–Zr Magnesium Alloys in the Product Form of a Large Structural Casting

Effect of heat treatment on microstructure and mechanical properties of Mg-4Y-1.6Nd-1Sm-0.5Zr alloy

Microstructures and Mechanical Properties of High Performance Mg–4Y–2.4Nd–0.2Zn–0.4Zr Alloy

The Role of Initial Grain Size on Bimodal-Grained Microstructure and Mechanical Properties of an Extruded Mg-Gd-Y-Nd-Zr Alloy

Effect of Cooling Method on Microstructures and Mechanical Properties of Extruded Mg-4.4Zn-0.3Zr-0.4Y Alloy

Effect of Heat Treatment on Microstructure, Mechanical Properties and Fracture Behaviors of Sand-Cast Mg-4Y-3Nd-1Gd-0.2Zn-0.5Zr Alloy

Microstructural Evolution and Mechanical Properties of Mg-5y-5gd-Xnd-0.5zr Magnesium Alloys at Different States

Effect of Zn Addition on Microstructure and Mechanical Properties of Mg–9Gd–3Y–0.5Zr Alloy