Abstract:Nylon 6 and its blends with a polyamide block copolymer were prepared by solvent blending and co-precipitation process.The samples were melted at 260℃ and then cooled at a rate of 30 K/min to obtain the controlled cooling samples(CCS).Investigations were carried out on the influence of thermal treatment on crystal melting behavior and crystal structure of nylon 6 and the blends by differential scanning calorimetry (DSC),wide-angle X-ray diffraction(WAXD)and polarized optical microscopy(POM).Measurements were taken after annealing at 190℃ with varied time from O h to 48 h.The resuhs indicated that the existing of the polyamide block copolymer affected the crystal behavior and the crystal structure of nylon 6,comparing to those of pure nylon 6 under the same thermal conditions.The pure nylon 6 tends to form α crystals,but it in the blends forms γ crystals.It was also found that annealing treatment had different effects on these two kinds of samples.For Nylon 6,annealing treatment only promoted the transformation of nylon 6 from amorphous to crystal phase,improved the crystalline structure and increased the crystal degree greatly without crystal form change.The crystal degree increased by about 61% after annealing for 48 h.For the blends.annealing treatment not only promoted the transformation from amorphous to crystal phase,improved the γ form crystalline structure and increased the crystal degree,but also resulted in the formation new α crystals.Compared with the original sample,the crystal degree increased by about 84%after annealing for 48 h.

A Kinetic Study of the Thermal Degradation of Nylon-6/Attapulgite Nanocomposites

Effect of Dendrimer‐like PAMAM Grafted Attapulgite on the Microstructure and Morphology of Nylon‐6

Thermal–oxidative Degradation and Accelerated Aging Behavior of Polyamide 6/epoxy Resin‐modified Montmorillonite Nanocomposites

Investigation of thermal degradation and flammability of polyamide-6 and polyamide-6 nanocomposites

Effect of Thermal Oxidative Aging on the Crystallization Behavior and Properties of Nylon-6

Evaluation of the thermal degradation of PC/ABS/montmorillonite nanocomposites

Kinetics of Thermo-Oxidative Degradation of Polypropylene/Aluminum Trihydroxide/Organo Fe-Montmorillonite Nanocomposites

Thermal Degradation Kinetics and Viscoelastic Behavior of Poly(Methyl Methacrylate)/Organomodified Montmorillonite Nanocomposites Prepared via In Situ Bulk Radical Polymerization

Thermal and dynamic mechanical properties of attapulgite reinforced poly(butylene succinate-co-1,2- octanediol succinate) nanocomposites

Thermogravimetric Kinetic Analysis of PC/ABS/montmorillonite Nanocomposites

INFLUENCE OF THERMAL TREATMENT ON CRYSTAL MELTING BEHAVIOR AND CRYSTAL STRUCTURE OF NYLON 6 AND POLYAMIDE BLOCKCOPOLYMER/NYLON 6 BLENDS

Preparation and Properties of PA6/Epoxy-resin-modified Montmorillonite Nanocomposites

STUDY ON NYLON 6/Nano-Tio2 AND NYLON 6/Nano-Al2o3 COMPOSITES VIA IN SITU POLYMERIZATION

Thermal Stability, Smoke Emission and Mechanical Properties of Poly(vinyl Chloride)/hydrotalcite Nanocomposites

A study on attapulgite reinforced PA6 composites

Preparation of a Novel Stabilizer and Its Thermal‐oxidative Stabilization Effect on Polyamide 6

Thermogravimetric evaluation of PC/ABS/montmorillonite nanocomposite

Flammability and phase-transition studies of nylon 6/montmorillonite nanocomposites

Preparation and Rheology of Polyamide-6/Attapulgite Nanocomposites and Studies on Their Percolated Structure

Porous‐structured vermiculite/polybutylene adipate terephthalate composite films: The morphology, mechanical properties, and nonisothermal degradation kinetics

Thermal Degradation Kinetics of G-Ha/pla Composite