Abstract:In this study, cooling of a plastic pipe-end during a hot-forming process that is one of the commonly used forming methods in plastic pipe production to get seal housing place (muff) was investigated numerically and experimentally. The aim of this study was development of a cooling die that has higher cooling performance and easier manufacturability. Cooling is supplied by the circulation of conditioned water in the channels located in the die in plastic production. The geometry of these channels and mass flow rate and temperature of the cooling water are the parameters affecting the quality of the formed region and process time. In the study, experimental analyses were performed, then numerical analyses were realised and validated with the experimental results for the existing die geometry. Continuity, momentum and energy equations were solved all together and heat transfer was investigated. After validating the model, a few different alternative die models were proposed and analysed to get an optimum which has highest cooling capacity and process ability. At the end of these studies, optimum alternative die geometry was determined. The channels in the suggested die were developed to increase the homogeneity of the cooling by changing the existing channel’s shape which can be produced by only longitudinal holes. A simple production method was also suggested for the new die to locate the channels following the circumference of the pipe, like conformal cooling channels. Additionally, aluminium material was also used to decrease the pipe temperature and die weight in the analyses. In conclusion, although cooling process time and mean temperature of the pipe-end were 30 secs and 43.9 o C respectively for the existing cooling die, these values were determined as 30 secs and 39.5 o C for the optimised aluminium die. If the temperature of the cooled pipe is taken as the same with the existing cooling, the cooling time decreases to around 20 secs for the suggested die. The weight of the die was reduced from 86.57 kg to 16.22 kg.

Effect of Die Temperature on Morphology and Performance of Polyethylene Pipe Prepared Via Mandrel Rotation Extrusion

Role of Melt Plasticizing Temperature in Morphology and Properties of PE100 Pipes Prepared by a Rotational Shear System

The effect of high-temperature annealing on thermal properties and morphology of polyethylene pipes prepared by rotational shear

Effect of mandrel rotation speed on morphology and mechanical properties of polypropylene pipes produced by rotational shear

The Microstructure-Tensile Property Relationship of Polyethylene Resin for Biaxially Stretched Film

The effect of annealing time on morphology, mechanical properties, and thermal conductivity of HDPE pipes produced by rotational shear

Enhanced effect of thermal expansion process in rotational shear technology for high performance HDPE pipes

Biaxial reinforcements for polyethylene medical-tubes via helical convergent flow

The influence of formation temperatures on the crystal structure and mechanical properties of ultrahigh-molecular-weight polyethylene/high-density polyethylene-blend fibers prepared by melt spinning

Study on the effect of the molding process and service temperature on the mechanical properties and low‐velocity impact performance of the ultra‐high molecular weight polyethylene fiber laminates

Effect of Morphology Development on the Low‐temperature Tensile Properties of PP / POE Blends

Synergistic Effects of Α/β-Nucleating Agents on Propylene-Ethylene Random Copolymer: New Clues for the Pipe Extrusion

Optimization of hot drawing process of ultra‐high molecular weight polyethylene monofilament prepared by melt spinning

The role of expansion angle and speed on shish-kebab formation in expansion pipe extruder head explored by high temperature rapid stretch

Cooling and annealing of plastic pipe

Study on Preparation of Ultra-High-Molecular-Weight Polyethylene Pipe of Good Thermal-Mechanical Properties Modified with Organo-Montmorillonite by Screw Extrusion

Tensile Behavior of High-Density Polyethylene Including the Effects of Processing Technique, Thickness, Temperature, and Strain Rate

DEVELOPMENT OF A COOLING DIE USED IN PLASTIC PIPE PROCESSING: NUMERICAL AND EXPERIMENTAL ANALYSIS

On structures and properties of polyethylene during heating and cooling processes based on molecular dynamics simulations

Effect of β nucleating agent and rotational shear on morphology and mechanical properties of polypropylene pipes

Investigating the Deformation Characteristics of Buried High-Density Polyethylene Pipes: Considering the Effect of Sequentially Applying Pressure and Elevating Temperature