Abstract:Obtaining a perovskite light-absorbing layer with good crystallization, low defect concentration, good stability, and well-matched energy levels is critical to obtaining high-efficiency perovskite solar cells (PSCs). Here, a hybrid PSC with a graded band gap is explored using MAPbBr3 (MA = CH3NH3) and MAPbBr0.9I2.1 quantum dots (QDs) as component cells. We have creatively designed a solar cell device with a double-QD structure [indium tin oxide (ITO)/SnO2/perovskite:MAPbBr3 QDs/MAPbBr0.9I2.1 QDs/Spiro-OMeTAD/Au]. A better crystal film of the perovskite absorption layer can be obtained because the MAPbBr3 QDs are doped in an antisolvent, which induces nucleation and growth in the polycrystalline perovskite. In addition, we expect that digestive ripening occurred in the crystallization, and the oleic acid ligands on the surface of the QDs disintegrate during the doping process and transfer to the surface of the perovskite absorption layer finally; it follows that the hydrophobicity and stability of the perovskite film are greatly enhanced. Moreover, a thin film of MAPbBr0.9I2.1 QDs is introduced between the perovskite absorption layer and the hole layer, acting as an energy-level ladder, which leads to well-matched energy levels, an increase in fill factor (FF), and an enhanced hole transport capability. In particular, the mechanism of the crystallization process involving the effect of oleic acid ligands on the interior and surface of the perovskite film is fully discussed here. The final research results from the PSCs show that both high efficiency and long-term stability are achieved successfully by this design strategy.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c14191?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c14191</a>.Parameters of carrier lifetimes in TRPL, parameters and calculated values in the Owens two-liquid method experiment, and J–V parameters; QD dispersion images; AFM images; perovskite film images; contact-angle test images; EIS spectrum; and boxplot of J–V parameters (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c14191/suppl_file/am0c14191_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

TiO2quantum Dots As Superb Compact Block Layers for High-Performance CH3NH3PbI3perovskite Solar Cells with an Efficiency of 16.97%

TiO 2 quantum dots as superb compact block layers for high-performance CH 3 NH 3 PbI 3 perovskite solar cells with an efficiency of 16.97%

Influence of Different TiO2 Blocking Films on the Photovoltaic Performance of Perovskite Solar Cells

A Small‐Molecule “charge Driver” Enables Perovskite Quantum Dot Solar Cells with Efficiency Approaching 13%

Tio2/Zno/Tio2 Sandwich Multi-Layer Films As A Hole-Blocking Layer for Efficient Perovskite Solar Cells

Low-Temperature TiOx Compact Layer for Planar Heterojunction Perovskite Solar Cells.

Efficient Inorganic Solid Solar Cells Composed of Perovskite and PbS Quantum Dots.

CH 3 NH 3 PbBr 3– x I x Quantum Dots Enhance Bulk Crystallization and Interface Charge Transfer for Efficient and Stable Perovskite Solar Cells

Perovskite Solar Cell Using a Two-Dimensional Titania Nanosheet Thin Film as the Compact Layer.

Atomic Layer Deposition of TiO2 for a High-Efficiency Hole-Blocking Layer in Hole-Conductor-Free Perovskite Solar Cells Processed in Ambient Air

Liquid Phase Deposition of Tio2 Nanolayer Affords Ch3nh3pbi3/Nanocarbon Solar Cells with High Open-Circuit Voltage

Perovskite Quantum Dots as Multifunctional Interlayers in Perovskite Solar Cells with Dopant-Free Organic Hole Transporting Layers

An Effective TiO2 Blocking Layer for Hole-Conductor-free Perovskite Solar Cells Based on Carbon Counter Electrode

Tri-functionalized TiO Cl4-2 accessory layer to boost efficiency of hole-free, all-inorganic perovskite solar cells

Dual Interfacial Modification Engineering with 2D MXene Quantum Dots and Copper Sulphide Nanocrystals Enabled High‐Performance Perovskite Solar Cells

Efficient perovskite/fullerene planar heterojunction solar cells with enhanced charge extraction and suppressed charge recombination.

Radio Frequency Magnetron Sputtering Deposition of TiO2 Thin Films and Their Perovskite Solar Cell Applications

Oxidized Nickel to Prepare an Inorganic Hole Transport Layer for High-Efficiency and Stability of CH3NH3PbI3 Perovskite Solar Cells

Efficient Perovskite Solar Cells Depending on TiO2 Nanorod Arrays.

An Excellent Modifier: Carbon Quantum Dots for Highly Efficient Carbon‐Electrode‐Based Methylammonium Lead Iodide Solar Cells

Ultrathin Cu 2 O as an efficient inorganic hole transporting material for perovskite solar cells