Abstract:Obtaining a perovskite light-absorbing layer with good crystallization, low defect concentration, good stability, and well-matched energy levels is critical to obtaining high-efficiency perovskite solar cells (PSCs). Here, a hybrid PSC with a graded band gap is explored using MAPbBr3 (MA = CH3NH3) and MAPbBr0.9I2.1 quantum dots (QDs) as component cells. We have creatively designed a solar cell device with a double-QD structure [indium tin oxide (ITO)/SnO2/perovskite:MAPbBr3 QDs/MAPbBr0.9I2.1 QDs/Spiro-OMeTAD/Au]. A better crystal film of the perovskite absorption layer can be obtained because the MAPbBr3 QDs are doped in an antisolvent, which induces nucleation and growth in the polycrystalline perovskite. In addition, we expect that digestive ripening occurred in the crystallization, and the oleic acid ligands on the surface of the QDs disintegrate during the doping process and transfer to the surface of the perovskite absorption layer finally; it follows that the hydrophobicity and stability of the perovskite film are greatly enhanced. Moreover, a thin film of MAPbBr0.9I2.1 QDs is introduced between the perovskite absorption layer and the hole layer, acting as an energy-level ladder, which leads to well-matched energy levels, an increase in fill factor (FF), and an enhanced hole transport capability. In particular, the mechanism of the crystallization process involving the effect of oleic acid ligands on the interior and surface of the perovskite film is fully discussed here. The final research results from the PSCs show that both high efficiency and long-term stability are achieved successfully by this design strategy.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c14191?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c14191</a>.Parameters of carrier lifetimes in TRPL, parameters and calculated values in the Owens two-liquid method experiment, and J–V parameters; QD dispersion images; AFM images; perovskite film images; contact-angle test images; EIS spectrum; and boxplot of J–V parameters (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c14191/suppl_file/am0c14191_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

TiO 2 quantum dots as superb compact block layers for high-performance CH 3 NH 3 PbI 3 perovskite solar cells with an efficiency of 16.97%

A Small‐Molecule “charge Driver” Enables Perovskite Quantum Dot Solar Cells with Efficiency Approaching 13%

In Situ Formation of Iodide Precursor for Perovskite Quantum Dots with Application in Efficient Solar Cells

Perovskite Quantum Dots Exhibiting Strong Hole Extraction Capability for Efficient Inorganic Thin Film Solar Cells

CH 3 NH 3 PbBr 3– x I x Quantum Dots Enhance Bulk Crystallization and Interface Charge Transfer for Efficient and Stable Perovskite Solar Cells

Efficient Inorganic Solid Solar Cells Composed of Perovskite and PbS Quantum Dots.

Colloidal CuInS2 Quantum Dots as Inorganic Hole-transporting Material in Perovskite Solar Cells.

Enhancing the Performance of Perovskite Solar Cells by Hybridizing SnS Quantum Dots with CH3NH3PbI3

Perovskite Quantum Dots as Multifunctional Interlayers in Perovskite Solar Cells with Dopant-Free Organic Hole Transporting Layers

Alloyed (Cu2SnS3)x(ZnS)1−x quantum dots as a hole-transporting layer for efficient and stable perovskite solar cells

Hybrid PbS Quantum-Dot-in-Perovskite for High-Efficiency Perovskite Solar Cell.

Dual Interfacial Modification Engineering with 2D MXene Quantum Dots and Copper Sulphide Nanocrystals Enabled High‐Performance Perovskite Solar Cells

Black Phosphorus Quantum Dots Induced High‐Quality Perovskite Film for Efficient and Thermally Stable Planar Perovskite Solar Cells

Fluorine Functionalized MXene QDs for Near‐Record‐Efficiency CsPbI3 Solar Cell with High Open‐Circuit Voltage

Influence of Different TiO2 Blocking Films on the Photovoltaic Performance of Perovskite Solar Cells

Goethite Quantum Dots As Multifunctional Additives for Highly Efficient and Stable Perovskite Solar Cells

Effects of CsSnxPb1−xI3 Quantum Dots as Interfacial Layer on Photovoltaic Performance of Carbon-Based Perovskite Solar Cells

Enhancing Perovskite Solar Cell Performance by Interface Engineering Using CH3NH3PbBr0.9I2.1 Quantum Dots.

CH3NH3PbBr3 Quantum Dot-Induced Nucleation for High Performance Perovskite Light-Emitting Solar Cells.

Passivation Effect of CsPbI3 Quantum Dots on the Performance and Stability of Perovskite Solar Cells

An Excellent Modifier: Carbon Quantum Dots for Highly Efficient Carbon‐Electrode‐Based Methylammonium Lead Iodide Solar Cells