Abstract:For advanced performance lithium-ion batteries (LIBs) various novel electrode materials with high energy density have been extensively investigated. Cobaltosic oxide (Co3O4), commonly used as an anode in LIBs, has attracted much interest because of its high theoretical specific capacity (890 mAh center dot g(-1)), high tap density, and stable chemical properties. However, its practical use has been hindered because of its low electronic conductivity and poor rate capability. To address these problems, we investigated a liquid phase precipitation method followed by thermal treatment and obtained a unique lamellar Co3O4 powder. Its X-ray diffraction (XRD) diffraction peaks match the standard pattern for cubic phaseCo(3)O(4) with good crystallinity. We found that the Co3O4 powder consists of many irregular sheets (1.5-3.0 mu m in diameter, 100-300 nm in thickness) with numerous poles by scanning electronmicroscopy (SEM). Additionally, the surface area was about 30.5m(2) center dot g-1, and this was calculated from BET nitrogen adsorption isotherm measurement data. Remarkably, perfect performance was obtained as evaluated by electrochemical measurements, including a high initial discharge capacity (1444.5 mAh center dot g(-1) at 0.1C) and excellent capacity retention (charge capacity after 50 cycles was still greater than 1100.0 mAh center dot g(-1) at 0.1C). However, its rate capability was still not adequate (75.3% of the first charge capacity after 50 cycles at 1C). To improve the rate capability, commercial carbon nanotubes (CNTs) mixed with the Co3O4 powder was used to enhance the electronic conductivity. The charge capacity retention ratios were 96.3% after 70 cycles at 1C and 97.0% after 50 cycles at 2C. Therefore, enhanced electrochemical performance with impressive rate capability was obtained, as expected.

On the evaluation of the factors influencing the rate capability of a LiCoO 2 |Li battery

Investigation on the Strategies for Discharge Capacity Improvement of Aprotic Li-CO 2 Batteries

Promoting Surface Electric Conductivity for High-Rate LiCoO<sub>2</sub>

The limitation mechanisms on the discharge behavior of Li-O 2 batteries

Kinetic and transport characteristics of LiNi0.8Co0.1Mn0.1O2 lithium-ion batteries

Factors Affecting Rate Capability of Graphite Electrodes for Lithium-Ion Batteries

Improving diffusion kinetics and phase stability of LiCoO2 via surface modification at elevated voltage

Investigation on the Strategies for Discharge Capacity Improvement of Aprotic Li-CO2 Batteries

The degradation of LiCoO 2 /graphite batteries at different rates

Synthesis and Modification of a Lamellar Co3O4 Anode for Lithium-Ion Batteries

Simulation study of rate limiting factors of Li-ion batteries using experimental functions of electronic and ionic resistances

Calculation on density of states and electrochemical performance of LixNi0.5Co0.5O2

Discharge Rate Capability of the LiCoO2 Electrode

Nanoscale Control and Tri-Element Co-Doping of 4.6 V LiCoO2 with Excellent Rate Capability and Long-Cycling Stability for Lithium-Ion Batteries.

The Effect of Different Amounts of Conductive Carbon Material on the Electrochemical Performance of the LiFePO4 Cathode in Li-Ion Batteries

Investigating the Coating Effect on Charge Transfer Mechanisms in Composite Electrodes for Lithium-Ion Batteries

LiFePO4/C composites with high compaction density as cathode materials for lithium-ion batteries with high volumetric energy density

Optimization of electrode loading amount in lithium ion battery by theoretical prediction and experimental verification

Influence of Coexisting Li3PO4 on Electrochemical Properties of LiFePO4

Toward The Rational Design Of Cathode And Electrolyte Materials For Aprotic Li-Co2 Batteries: A Numerical Investigation

In Situ Low-Temperature Carbonization Capping of LiFePO4 with Coke for Enhanced Lithium Battery Performance