Abstract:In recent decades, the high catalytic activity of MgAl mixed oxides (MOs) and rehydrated hydrotalcites (HTCs) has made them very promising basic catalysts for various organic reactions. The synthesis procedure as well as the mechanism of the formation of HTC structure has been well described. Despite this, little has been published on how synthetic parameters affect the physico-chemical properties, rehydration ability and performance of the hydrotalcite-derived catalysts. Here, a series of catalysts with the same molar ratio Mg/Al = 3 varied by the co-precipitation conditions (pH value, temperature, ageing duration) were synthesized and used as precursors for the preparation of the MgAl MOs and rehydrated HTCs. The set of methods (AAS, XRD, SEM, N 2 -physisorption, TGA and CO 2 -TPD) was used to establish a relation between the synthetic parameters and the physico-chemical properties of the prepared materials. Their catalytic performance was monitored in aldol condensation of furfural and acetone as a model reaction. Preparations at different pH values and temperature resulted in the formation of HTC samples with crystallite size evaluated by XRD in the range of 70–230 Å ( d 003 ). Nevertheless, the crystallite size of the resulting MOs was similar in the range of 30–36 Å ( d 003 ). The rehydration of the MOs for 5–120 min produced high-crystalline reconstructed HTC with a crystalline size in the range of 82–111 Å ( d 003 ), i.e. the crystallite size of a large-size HTC precursor was not restored. Catalytic results revealed that the crystallite size of an as-prepared HTC precursor was a crucial parameter that affected the performance of both MOs and reconstructed HTCs in the condensation reaction. Furfural conversion over MOs and short-time rehydrated (5–10 min) materials in the reaction was strongly dependent on initial size of the as-prepared HTC crystallites. In contrast, the catalytic performance of the catalysts rehydrated for 120 min, was similar: furfural conversion was above 99% in all cases. Based on these results, the effect of the physico-chemical properties of the as-prepared HTCs on the catalytic performance of both MOs and reconstructed MgAl HTCs was established. A difference in the properties of the prepared samples was explained assuming the existence of extra-framework or partially framework Al-rich species that prevented the access of reactant molecules to catalytically active sites: the larger the crystallite size of the as-prepared precursor, the higher the excess of both structural defects and non-framework Al-rich species, and the lower the furfural conversion over these catalysts. Nevertheless, long rehydration time favored the involvement of the Al-rich species in the recrystallization of HTC structure as evidenced by SEM. As a consequence, furfural conversion increased over these catalysts. These results provide a new insight into the influence of synthetic parameters on the properties of MOs and rehydrated HTCs: the crystallite size of the as-prepared precursors determines the performance of the produced catalysts in aldol condensation by affecting the rehydration ability of the derived MOs.

Promotional Effect of Transition Metal Doping on the Basicity and Activity of Calcined Hydrotalcite Catalysts for Glycerol Carbonate Synthesis

Transition Metal-Modified Mesoporous Mg-Al Mixed Oxides: Stable Base Catalysts for the Synthesis of Diethyl Carbonate from Ethyl Carbamate and Ethanol

Elucidating the Crystal Face- and Hydration-Dependent Catalytic Activity of Hydrotalcites in Biodiesel Production

Synthesis of Glycerol Carbonate by Transesterification of Glycerol with Dimethyl Carbonate over MgAl Mixed Oxide Catalysts

Synthesis of Dipropyl Carbonate over Calcined Hydrotalcite-Like Compounds Containing La

Effect of coprecipitation method on Mg–Al hydrotalcite properties: application in the synthesis of diethylene glycol di-(methyl carbonate)

Fluorinated Mg–Al Hydrotalcites Derived Basic Catalysts for Transesterification of Glycerol with Dimethyl Carbonate

Synthesis, Characterization, and Application of Hydotalcites in Hydrodesulfurization of FCC Gasoline

Active and Stable Hydrotalcite Derived Ni Catalysts for CO2 Reforming of Methane: Comparison with Catalysts by Incipient Wetness

Transition Metal-Promoted Hierarchical ETS-10 Solid Base for Glycerol Transesterification

EFFECT OF CALCINATION TEMPERATURE ON THE STRUCTURE AND CATALYTIC PERFORMANCE OF THE CU-MCM-41 CATALYSTS FOR THE SYNTHESIS OF DIMETHYL CARBONATE

Study of the Metal-Support Interaction and Electronic Effect Induced by Calcination Temperature Regulation and Their Effect on the Catalytic Performance of Glycerol Steam Reforming for Hydrogen Production

Hydrogenolysis of Glycerol to Propanediols on Cu–Ca–Al Hydrotalcites Derived Catalysts

Preparation and Characterization of Fe/MgO Catalysts Obtained from Hydrotalcite-Like Compounds

On the influence of synthetic parameters on the properties and aldol condensation performance of the MgAl mixed oxides and rehydrated hydrotalcites

Transesterification of glycerol with dimethyl carbonate over Mg-Al hydrotalcites

Influence of Y on the Performance of Mg-Al-Y Catalysts Via Hydrotalcite-Like Precursors for the Synthesis of Diethyl Carbonate from Ethyl Carbamate and Ethanol

Study of the catalytic activity of calcined hydrotalcites for Friedel–Crafts reactions

Transesterification of Glycerol with Dimethyl Carbonate over Calcined Ca-Al Hydrocalumite

Highly Selective Catalytic Oxidation of Glycerol by Cu-Containing Hydrotalcites

Catalysis of Hydrotalcite-Like Compounds in Liquid Phase Oxidation: