Abstract:The passive safety commercial pressurized water reactors (PWRs), AP1000 and CAP1400 are equipped with the automatic depressurization system (ADS). The fourth stage of ADS (ADS-4) has the largest discharging capacity among the all ADS stages. During a small break loss-of-coolant accident (SBLOCA), only when the system is fully depressurized by the ADS-4 to near the containment atmospheric pressure, the in-containment refueling water storage tank (IRWST) can deliver the large coolant inventory for the long-term core cooling by its water head. Before the IRWST injection, the core reaches its minimum inventory. So the transition from the ADS-4 depressurization to the IRWST injection is a very challenging period in a SBLOCA. Therefore, to evaluate the passive system performance by the integral effect test (IET), the transition must be simulated properly. This work conducted the scaling analysis for the ADS-4 depressurization and the IRWST injection for designing the related components of the ACME IET facility. A uniform scaling law based on the existing T-branch liquid entrainment models was proposed. For scaling the onset of the IRWST injection, the requirement for reproducing the synergetic effect in an IET was introduced in order to preserve the important event/process occurrence time with the proper conditions, and the scaling laws for the full pressure IRWST injection were obtained. For investigating the transition thermal hydraulic behaviors and the ADS-4 configuration influences on the core safety, one cold leg break test and three double-ended direct-vessel-injection (DEDVI) line break tests with the different ADS-4 failure modes were selected from the ACME SBLOCA test matrix, and the main test data related to the core safety were analyzed and compared. It was found that the ADS-4 actuation significantly accelerated the system depressurization but worsened the core inventory depletion at the same time. In addition, the break condition and the ADS-4 failure mode could differently affect the system depressurization and the core level. The ACC injection during the ADS-4 depressurization in DEDVI was critical for the core level makeup. The insufficient ADS-4 venting capacity delayed IRWST injection, but also mitigated the core inventory depletion. It suggests the ADS-4 design can be potentially optimized in the passive safety system design. (C) 2019 Elsevier Ltd. All rights reserved.

Experimental investigation of upper plenum entrainment in AP1000

Overview of Hl-2a Experiment Results

Overview of Experimental Results on the HL-2A Tokamak

OV / 4-5 1 Overview of Experimental Results on the HL-2 A Tokamak

Experimental Investigation of Pool Entrainment in High Gas Flux Region

An Experimental Study of Pool Entrainment with Side Exit

Experimental Study on the Influence of Velocity on Hydraulic Characteristics in Reactor Lower Plenum

Experimental study and theoretical development of liquid entrainment in T-junction with double inlets and single inlet of gas phase

Validation of RELAP5 MOD3.3 Code for Entrainment Phenomenon Against FATE Test Facility

Development and Applicability Analyses of ADS-4 Entrainment Model in Large Advanced PWR

Sensitivity Analysis of Stratification Entrainment Model of SCDAP/Relap5 3.2 Code

S0803-1-3 Study on Evaluation of Gas Entrainment in Nuclear Reactor Vessel Using Numerical Simulation Method

Thermofluid experiments on ingress of coolant event

Experimental investigations on the two-phase water entrainment phenomenon at inclined branch T-junctions and numerical simulations based on neptune_cfd

Experimental Investigation of ADS-4 Entrainment with Air and Boric Acid

An experimental investigation on pool entrainment under small air flowrate

Experimental and Theoretical Investigation on Pool Entrainment under Small Air Flow Rate

CFD simulation on the transient process of coolant mixing phenomenon in reactor pressure vessel

Air Ingress Analysis of Chimney Effect in the 200 MWe Pebble-Bed Modular High Temperature Gas-Cooled Reactor

Scaling and Integral Effect Test on Transition from Depressurization to Long-Term Gravity Injection

CFD analysis for full vessel upper plenum in Maanshan Nuclear Power Plant