Abstract:The usage of low-grade ferrous scrap has increased over decades to decrease CO2 emissions and to produce steel products at a low cost. A serious problem in melting post-consumer scrap material is the accumulation of tramp elements, e.g., Cu and Sn, in the liquid steel. These tramp elements are difficult to remove during conventional steelmaking processes. Sn is considered as one of the most harmful tramp elements because, together with Cu, it sometimes induces the liquid metal embrittlement in high-temperature ferrous processing, e.g., continuous casting and hot rolling. Furthermore, the chemical interaction between Fe and Sn plays an important role in the Sn smelting process. The raw material used in the Sn smelting process is SnO2 (cassiterite), in which Fe3O4 is a gangue in the Sn ore. In the process, the reduction of Fe3O4 is unavoidable, which results in forming a Fe-Sn alloy (hardhead). The recirculation of the hardhead decreases the furnace capacity and increases the energy consumption in the smelting. The need to efficiently recover Sn from secondary resources is therefore inevitable. The CALculation of PHAse Diagrams (CALPHAD) approach helps to predict the equilibrium state of the multicomponent system. Previously reported studies of the Fe-Sn system show inconsistencies in the calculations and the experimental results. Mainly the miscibility gap in the liquid phase was under debate, as experimental data of the phase boundary are scattered. Experimental study and re-optimization of model parameters were carried out with emphasis on the correct shape of the miscibility gap. Three different experimental techniques were employed: differential scanning calorimetry, electromagnetic levitation, and contact angle measurement. The present thermodynamic model has higher accuracy in predicting the solubility of Sn in the body-centered cubic (bcc), compared to previous assessments. This is achieved by re-evaluating the Gibbs energies of the FeSn and FeSn2 compounds and the peritectic reaction related to Fe5Sn3. Also, the inconsistencies related to the miscibility gap around XSn = 0.31-0.81 were resolved. The database developed in the present study can contribute to the development of a large CALPHAD database containing tramp elements.

Thermodynamic Description of the Cu–Sn System

Thermodynamic Descriptions of the Cu–Zn System

Phase Equilibria of Sn–Sb–Cu System

Thermodynamic Reassessment of the Binary Cu-Sn, Cu-P, and Sn-P and Ternary Cu-Sn-P Systems

Phase equilibria of the Ag–Sn–Cu ternary system

Liquidus Projection and Thermodynamic Modeling of Sn–Zn–Cu Ternary System

Phase Equilibria of the Cu-in System II: Thermodynamic Assessment and Calculation of Phase Diagram

Phase Equilibria of the Sn–Zn–Cu Ternary System

Phase Equilibria of the Sn-Sb Binary System

Experimental and Theoretical Study of the Ag-Sn-Te Phase Diagram

Thermodynamic description and simulation of solidification microstructures in the Cu–Mg–Zn system

Sn–Bi–Fe Thermodynamic Modeling and Sn–Bi/Fe Interfacial Reactions

Thermodynamic study of the Ca-Cu-Zn ternary system with key experimental measurements

Phase Equilibria and Solidification Properties of Sn-Cu-Ni Alloys

Crystal structure of Cu-Sn-In alloys around the η phase field studied by neutron diffraction

Phase diagram of Ag-Pb-Sn system

Thermodynamic Description of Systems Cd-Te, Hg-Te and Cd-Hg-Te Using the Model of Associated Liquid Solution

Thermodynamic Descriptions of the Quaternary Mg–Al–Zn–Sn System and Their Experimental Validation

Thermodynamic modeling of the Fe-Sn system including an experimental re-assessment of the liquid miscibility gap

Phase Equilibria of the Cu-Se-Te Ternary System

Directional Solidification and Liquidus Projection of the Sn-Co-Cu System