Abstract:In this study, we report the effect of cerium (Ce) addition on the tension-compression yield and cyclic asymmetry in commercially pure magnesium (Cp-Mg) and Mg-Al alloy at room temperature (RT). The investigated materials Cp-Mg, Mg-0.5Ce, and Mg-3Al-0.5Ce were extruded at 400°C, followed by annealing at the same temperature for one hour. Incorporating 0.5wt.% Ce in pure Mg results in the weakening of its basal texture, uniform distribution of Mg12Ce precipitates, and grain size refinement. Consequently, the tensile yield strength and ductility of pure Mg increased, and tension-compression yield asymmetry was eliminated. However, the presence of 3wt.% Al in Mg suppresses the beneficial effects of Ce addition. The formation of complex precipitates, such as Mg-Al-Ce and Al11Ce3, limits the weakening of the basal texture, reduction in grain size, improvement in ductility, and elimination of tension-compression yield asymmetry observed in Mg-0.5Ce. Nevertheless, Al contributes to the solid solution strengthening in Mg and possibly lowers the critical stress required for twinning in Mg, resulting in the highest tensile strength of Mg-3Al-0.5Ce. Finally, the addition of 0.5wt.% Ce enhances the cyclic strength, stabilizes cyclic stress response, reduces inelastic strain, and minimizes cyclic asymmetry in both pure Mg and Mg-Al alloy while maintaining a comparable fatigue life. Overall, Ce addition positively impacts the microstructure and mechanical behavior of pure Mg and its investigated alloy. The reasons for these improvements are discussed in detail.

The Effect of Addition of Cerium on the Grain Refinement of Mg–3Al–1Zn Cast Alloy

Effect of Cerium on Microstructure, Texture and Properties of Ultrahigh-Purity Copper

Effect of Ce Addition on the Microstructure, Thermal Conductivity and Mechanical Properties of Mg–0.5Mn Alloys

Effect of Ce Addition on Modifying the Microstructure and Achieving a High Elongation with a Relatively High Strength of As-Extruded AZ80 Magnesium Alloy

Effect of the addition of cerium on the microstructure evolution and thermal expansion properties of cast Al-Cu-Fe alloy

Effect of cerium alloying on microstructure, texture and mechanical properties of magnesium during cold-rolling process

Effect of Ce Addition on Microstructure, Thermal Conductivity, and Mechanical Properties of As-Cast and As-Extruded Mg–3Sn Alloys

Effect of Cerium Addition on Microstructure and Mechanical Properties of As-Cast High Grade Knives Steel

Tailoring the microstructure and enhancing the corrosion resistance of extruded dilute Mg-0.6Al-0.5Mn-0.25Ca alloy by adding trace Ce

Influence of Ce content on the microstructures and tensile properties of Mg-1Gd-0.5Zn alloys

Effect of Ce addition on thermal conductivity of Mg–2Zn–1Mn alloy

Towards reducing tension-compression yield and cyclic asymmetry in pure magnesium and magnesium-aluminum alloy with cerium addition

Influence of cerium treatment on inclusion modification and as-cast microstructure of high-strength low-alloy steel

Achieving high strength-ductility synergy in dilute Mg-Al-Ca alloy by trace Ce addition

Enhanced Mechanical Properties and Corrosion Resistance of Rolled Mg-1.5Sn-0.5Ca Alloy by Ce Microalloying

Effect of Ce Content on the Microstructure and Mechanical Properties of Al-Cu-Li Alloy

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Al-CeO2-Mg refiner on grain refinement, cast fluidity and mechanical properties of AZ91 alloy

Effect of rare earth Ce addition on microstructure and mechanical properties of titanium alloy Ti-6Al-4V

Effect of rare earth Ce on the microstructure and mechanical properties of cast Al–7Si alloys

Effect of Y and Ce Micro-alloying on Microstructure and Hot Tearing of As-Cast Al–Cu–Mg Alloy