Abstract:The electroplated diamond wire saw is a crucial tool for cutting semiconductor materials such as silicon ingots and sapphire. The nickel (Ni)-coated diamond serves as an essential abrasive in the production of electroplated wire saws. Nevertheless, producing Ni-coated diamonds necessitates the use of the precious metal palladium as a catalyst. Moreover, Ni-coated diamonds are prone to detachment from the wire saw during cutting, since no chemical bond is formed between Ni and the diamond. To address these issues, we proposed the production of electroplated diamond wire saws using Ni/titanium (Ti)-coated diamonds. The vacuum slow evaporation technology had been used to apply a uniform Ti coating on the diamond micro-powder (8 μm), which firmly bonded to the diamond through the interfacial product TiC. The Ti-coated diamonds exhibited surface activity, allowing direct electroless plating of the Ni coating without palladium. At an overpotential of −0.7 V, the current densities in the composite electroplating bath were − 0.026 A/cm2 (Ni/Ti-coated diamond) and − 0.018 A/cm2 (Ni-coated diamond). Additionally, electrochemical impedance spectroscopy showed that the charge transfer resistances were 3.72 Ω and 4.45 Ω, respectively. Thus, Ni/Ti-coated diamonds enhanced the composite electroplating reaction. The Ni/Ti-coated diamond wire saws also showed superior abrasive density per unit length. These improvements were ascribed to the formation of Ni and Ti coatings on the diamond surface. Moreover, the Ni/Ti-coated diamond wire saw exhibited greater resistance to detachment in cutting trials, allowing at least a twofold increase in diamond exposure. Utilizing Ni/Ti-coated diamond micro-powder as an abrasive in the electroplating of diamond wire saws offers a cost-effective and efficiency-enhancing solution for manufacturers, potentially extending the wire saw's lifespan. This development is poised to drive advancements in the processing technology of hard and brittle materials.

A New Cutting Wire Prepared by Copper-Diamond Composite Electroplating

Composite electroplating to enhance the GMI output stability of melt-extracted wires

Enhanced Tensile Properties And Fracture Reliability Of Cu-Based Amorphous Wires Via Pr-Doping

Ti-coated Diamond Micro-Powder for the Manufacture of the Electroplated Diamond Wire Saw

High Thermal Conductive Cu-diamond Composites Synthesized by Electrodeposition and the Critical Effects of Additives on Void-Free Composites

Preparation of the Ni/Ti-coated diamond micro-powder for electroplated diamond wire saws using vacuum slow evaporation technology combined with the palladium-free electroless plating

Optimization of External and Internal Conditions for High Thermal Conductive Cu-diamond Composites Produced by Electroplating

Preparation and application of nanocrystalline diamond composite coatings wiredrawing dies

Preparation and thermal conductivity of tungsten coated diamond/copper composites

Interface Engineering for High-Strength and High-Ampacity of Carbon Nanotube/copper Composite Wires

Design Strategy to Simultaneously Enhance Electrical Conductivity and Strength: Cold-Drawn Copper-Based Composite Wire with In-Situ Graphene

Critical effect and enhanced thermal conductivity of Cu-diamond composites reinforced with various diamond prepared by composite electroplating

Preparation and performance study of electroplated Ni–W/diamond ultrathin dicing blades

Study on the Anti-wear Behavior of Ni-Co/Diamond Nanocomposite Coatings

Deposition and Application of Cvd Diamond Film on the Interior-Hole Surface of Shaped-Wire Drawing Die

Fabrication of high thermal conductivity copper/diamond composites by electrodeposition under potentiostatic conditions

Studies on Electric Contact Silver Based Composite Deposit Intensified with Nano Crystal Diamond Particles

Uniform Deposition of Chemical Vapor Deposition Diamond Films on Slender Tungsten Wires

A New Wire Electrode for Improving the Machining Characteristics of High-Volume Fraction SiCp/Al Composite in WEDM

Study of the Preparation and Application of the Small-Aperture Wire Drawing Mold with HFCVD Diamond Film Coating

Progress in the Copper-Based Diamond Composites for Thermal Conductivity Applications