Abstract:Nanocrystalline barium titanate (BaTiO3, BT) was synthesized hydrothermally at 220°C by reacting barium hydroxide with titanium dioxide. The resulting BT nanopowders were characterized by X‐ray diffraction (XRD), selected area electron diffraction (SAED), Raman spectrum, scanning electron microscopy (SEM), and high‐resolution transmission electron microscopy (HR‐TEM). The BT nanopowders have a cubic phase as revealed by the XRD and SAED results, whereas the Raman spectrum indicates that tetragonal phase BT exists in the produced nanopowders but is not the dominant phase because of the weak characteristic peak of the tetragonal structure at 305 cm−1. In the SEM and TEM images, many coarse‐faceted cubic nanoparticles and a small amount of spherical particles are observed, indicating a developed bimodal size distribution of the BT powders. The variations of electron diffraction contrast across these particles in the TEM images indicate the presence of high strain in the BT nanoparticles, which is probably caused by the lattice defects like OH− ions and their compensation by cation vacancies. The HR‐TEM image of a BT nanoparticle with a size of 24 nm and a spherical morphology demonstrates a uniform and perfect crystal structure. The surrounding edges of the particle are very smooth and no surface steps are observed. However, a terrace–ledge–kink (TLK) surface structure was frequently observed at the edges of the BT nanoparticles with rough surface morphology, and in most cases the terrace and ledge lie on the {100} planes. The observed TLK surface structure can be well interpreted by the theory of periodic bond chains. Small nucleated and triangular BT islands with three to four atomic layer thickness, and their outside surfaces faceted as (100) and (010) planes, are also observed in these particles. The rarely seen {110} surface in the BT nanoparticles was found to be reconstructed so that the surface was composed of corners bound by {100} minifaces like the triangular small islands. Microstructural defects such as antiphase boundaries were also observed near the edge of a BT nanoparticle, which were formed by the intersection of two crystalline parts with displacement deviation from each other by , as revealed by the HR‐TEM images.

Microbiological Precipitation, Morphology and Thermal Behavior of Barium Hydrogen Phosphate

REMOVAL OF BARIUM - Ba (II) BY PHOSPHATE-MINERALIZATION MICROBE UNDER DIFFERENT STANDING TIME

BIO-INSPIRED SYNTHESIS OF BARIUM PHOSPHATES NANOPARTICLES AND ITS CHARACTERIZATION

Morphology of Barium Hydrogen Phosphate Formation Induced by Phosphate-Mineralization Microbe

Microbiological Precipitation of Strontium Carbonate

Biosynthesis of Magnesium Phosphates and Its Thermal Property

Microscopic and Spectroscopic Insights into Uranium Phosphate Mineral Precipitated by Bacillus Mucilaginosus

Atomic‐Scale Characterization of Barium Titanate Powders Formed by the Hydrothermal Process

Effect of Ba2+ on the biomineralization of Ca2+ and Mg2+ ions induced by Bacillus licheniformis

Tem Characterization and Raman Spectra of Hydrothermal Batio3 Nanoparticles

Thermal Decomposition of Barium(ii) Tetraphenylborate

Hydrothermal derived barium niobate ultra-fine powders and nanowires

Controllable Preparation Of Uniform Micron-Sized Barium-Sulfate Spheres

The effect of pH on morphological control of barium hydrogen phosphate crystal by a double-hydrophilic copolymer

Crystal Structure and Thermal Decomposition Studies of Barium Borophosphate, BaBPO5

Mechanism of Thermal Decomposition of Barium Benzoate

Thermodynamic and Kinetic Studies of the Precipitation of Double-Doped Amorphous Calcium Phosphate and Its Behaviour in Artificial Saliva

Effects of PSMA additive on morphology of barite particles

Non-ureolytic Microbiologically-induced Calcium Carbonate Precipitation

Influence of Acidic Impurities on Rheological Properties of Boron/Agglomerated Boron and HTPB Slurry

Morphology Modification of Micron-Sized Barium Strontium Titanate by Hydrothermal Growth