Hydrodeoxygenation of Lignin-Derived Phenols into Alkanes over Carbon Nanotube Supported Ru Catalysts in Biphasic Systems

Meng-Yuan Chen,Yao-Bing Huang,Huan Pang,Xin-Xin Liu,Yao Fu

DOI: https://doi.org/10.1039/c4gc01992j

IF: 9.8

2014-01-01

Green Chemistry

Abstract:Lignin derived phenols and dimers were converted into alkanes through the HDO process over Ru/CNT catalysts in biphasic solvents.

What problem does this paper attempt to address?

Aqueous Phase Partial Hydrodeoxygenation of Lignin-Derived Phenols over Al2o3-Sio2 Microspheres Supported Rumn Multifunctional Catalyst: Synergic Effect among Ru, Mn and Al2o3-Sio2 Support

Mengting Chen,Qifeng Zhong,Meihua Zhang,Hao Huang,Yingxin Liu,Zuojun Wei

DOI: https://doi.org/10.1016/j.catcom.2022.106550

2022-01-01

SSRN Electronic Journal

Abstract:Herein, RuMn/Al2O3-SiO2 multifunctional catalyst was prepared and efficiently converted lignin-derived phenols into cyclohexanol by aqueous partial hydrodeoxygenation (HDO). The optimal RuMn/Al2O3-SiO2 (Ru/Mn = 2) catalyst achieved 96.8% of cyclohexanol yield with 100% guaiacol conversion under mild reaction conditions (180 °C and 2.0 MPa H2) for 4 h, with a turnover frequency (TOF) of 861.1 h−1, which is better than most results reported. The high performance of RuMn/Al2O3-SiO2 was attributed to the synergic effect of highly dispersed Ru nanoparticles with small size (1.25 nm), the microsphere structure, the appropriate acid sites from Al2O3-SiO2 and acid-base sites from MnOx.
Hydrogenolysis and Hydrodeoxygenation of Lignin in a Two-Step Process to Produce Hydrocarbons and Alkylphenols

Biqin Lin,Rongxuan Li,Riyang Shu,Chao Wang,Zhengdong Cheng,Ying Chen

DOI: https://doi.org/10.1016/j.joei.2019.05.004

IF: 6.47

2020-01-01

Journal of the Energy Institute

Abstract:Valuable fuels and chemicals production from biomass with high yields is always a big challenge in the energy utilization field. Herein, a two-step process for the catalytic conversion of lignin was proposed to form the fuels. In the first step, the depolymerization of lignin occurred efficiently via the hydrogenolysis reaction, resulting in 19.2% aromatic monomers under the catalysis of Pd/C and CrCl3. The catalysts exhibited a synergistic effect on the cleavage of β-O-4 bonds and the hydrogenation procedure, which prevented the condensation of intermediate products remarkably. Afterwards, the aromatic monomers were extracted out with octane solvent successfully (extraction degree 89.7%) and then used as a substrate in a second hydrodeoxygenation (HDO) step. Product mixture composed of 26.5% hydrocarbons (increased from 5.5%) and 49.7% alkylphenols (increased from 42.9%) were obtained after the HDO upgrading, which exhibited high potential to be used as fuels. This two-step approach is very promising to be a practical chemical engineering process for the fuel production from lignin.
A Review on the Catalytic Hydrodeoxygenation of Lignin-Derived Phenolic Compounds and the Conversion of Raw Lignin to Hydrocarbon Liquid Fuels

Riyang Shu,Rongxuan Li,Biqin Lin,Chao Wang,Zhengdong Cheng,Ying Chen

DOI: https://doi.org/10.1016/j.biombioe.2019.105432

IF: 5.774

2020-01-01

Biomass and Bioenergy

Abstract:Petroleum, one of the fossil fuels, is still the main source for liquid fuel production. Lignin derived from renewable biomass has the potential to replace petroleum. The abundance of aromatic units in lignin makes it potential to produce high-value liquid fuel. This review offers a summary of the extensive study that has been devoted to the catalytic hydrodeoxygenation (HDO) of lignin-derived phenolic compounds and the conversion of raw lignin into hydrocarbon liquid fuels. Based on the product classification (cyclohexanes and arenes), different catalytic systems, mainly including catalyst species, solvents and reaction conditions, are analyzed in detail. A model study of lignin-derived compounds (phenolic monomers and dimers) is usually carried out to elaborate on the HDO reaction mechanism. 100% yield of hydrocarbon liquid fuels can be achieved in most tests. With respect to the real lignin-derived bio-oil, however, hydrocarbon yields only reach 16.2%–62.8% due to the various components and high instability of the substrate. The technical barriers and challenges in this part are highlighted throughout. Moreover, the conversion of raw lignin is also comprehensively summarized, which actually combines the depolymerization of lignin and HDO of lignin-derived bio-oil in one pot, and its hydrocarbon yields are generally lower than those of lignin-derived bio-oil. In light of this, the important features of raw lignin that influence the production of hydrocarbon liquid fuels are adequately addressed. Overall, this paper focuses on the scientific and technological advances of hydrocarbon liquid fuel production from lignin, and the potential strategies to produce renewable fuels from lignin are discussed.
One-pot Hydrodeoxygenation (HDO) of Lignin Monomers to C9 Hydrocarbons Co-Catalysed by Ru/C and Nb2O5

Simin Li,Baoyuan Liu,Julianne Truong,Zhongyang Luo,Peter C. Ford,Mahdi M. Abu-Omar

DOI: https://doi.org/10.1039/d0gc01692f

IF: 9.8

2020-01-01

Green Chemistry

Abstract:A physical mixture of Ru/C and Nb2O5 is an effective catalyst for upgrading lignin monomers under low H2 pressure at 250 °C to a clean cut of hydrocarbon liquid fuels.
Water-assisted selective hydrodeoxygenation of phenol to benzene over the Ru composite catalyst in the biphasic process

Cheng Zhang,Chuhua Jia,Yang Cao,Yao Yao,Shaoqu Xie,Shicheng Zhang,Hongfei Lin

DOI: https://doi.org/10.1039/c8gc04017f

IF: 9.8

2019-01-01

Green Chemistry

Abstract:Aromatic hydrocarbons as a liquid fuel have unique combustion properties (high volume energy density, etc.). Thus preserving the aromatic rings while selectively cleaving the C-O bonds in the hydrodeoxygenation of lignin derived substituted phenols without additional consumption of H-2 is of crucial importance. In this regard, the composite materials, which are used as the catalyst support, were prepared through the hybridization of Nb2O5 (niobium oxide) with MC (micro-mesoporous carbon). Ru NPs (nanoparticles) were loaded on the Nb2O5-MC composite supports by the incipient wetness impregnation method. And then the as-synthesized catalysts were characterized by various techniques, including XRD, SEM, TEM, BET, NH3-TPD, XPS, etc. Under mild conditions (200-250 degrees C and 2.0-10 bar H-2), the Ru/Nb2O5-MC catalyst was proved to be highly effective for the hydrodeoxygenation (HDO) of phenol. With regard to achieving a high selectivity to benzene, the biphasic catalytic process in the decalin/water mixed solvent was superior to the monophasic processes in either the decalin or water solvent under the same conditions. Water acted as a co-solvent that prevented the occurrence of side reactions and promoted the catalytic C-O bond scission of phenol. The synergistic effect of the biphasic solvents (decalin and water) and the Ru/Nb2O5-MC composite catalysts, which might stabilize the emulsions and decrease the activation energy of HDO, was investigated. Meanwhile, other probe reactions were conducted to elucidate the mechanism of the HDO of phenol. The application of the efficient biphasic catalytic process may provide a promising approach for improving lignin valorization.
Efficient Hydrodeoxygenation of Lignin-Derived Phenols to C6+Cycloalkanols/Cycloalkanes over Magnetic Carbon-Encapsulated Nickel Nanospheres

Yingbo Zhu,Nan Ma,Yulong Ma,Yonggang Sun,Liqiong Wang,Yuanyuan Li,Tingting Gao,Feng Lin

DOI: https://doi.org/10.1021/acs.energyfuels.2c04221

IF: 4.6541

2023-01-01

Energy & Fuels

Abstract:To obtain value-added fuels and chemicals from lignin, it is necessary to explore an efficient catalytic system for hydrodeoxygenation (HDO). In this study, a highly efficient and magnetically separable Ni@C catalyst was synthesized for conversion of lignin-derived phenols. Detailed results showed that the pyrolysis temperature played a crucial role in the difference of the carbon-defect degree, which increased the metal dispersion and the strong electronic metal-support interactions. Meanwhile, we revealed that the differentiated pyrolysis temper-ature induced the appropriate presence of Ni2+ as Lewis acid sites and Ni delta+ as heterohydrogen cleavage sites, which provided an acceleration effect for the HDO reaction. The results displayed that higher reactivity of lignin-derived phenols into C6+ cyclo-alkanols was achieved over the Ni@C catalyst (100% conversion and 87.19% selectivity). Moreover, the high selectivity of C6+ cycloalkanes was achieved after adding H-ZSM-5 as Bronsted acid sites (100% conversion and 100% selectivity). This investigated work offers an efficient strategy for conversion of lignin-derived aromatics into value-added chemicals.
Efficient Hydrodeoxygenation of Lignin‐derived Phenolic Compounds over Ru‐based Catalyst with Biochar and Al2O3 as Composite Support

Tao Yin,Yichao Ye,Hao Jiang,Chengyin Lin,Riyang Shu,Zhipeng Tian,Chao Wang,Ning Shi

DOI: https://doi.org/10.1002/cssc.202401870

IF: 8.4

2024-10-20

ChemSusChem

Abstract:Hydrodeoxygenation (HDO) is a common strategy for upgrading lignin‐derived phenolic compounds into high‐quality liquid fuels, and the support rational design of HDO catalysts is critical to achieve a good reaction performance. This work proposed a novel Ru‐based catalyst with biochar and Al2O3 as composite support. The addition of biochar can enlarge the porous structure, and the addition of Al2O3 can enhance the acid property of the support. By regulating the content of biochar and Al2O3 components, Ru/CA‐2 catalyst achieved the best HDO performance of lignin‐derived phenolic compounds, with the optimal component balance of 50%C and 50%Al2O3. This catalyst possesses the high Ru metal dispersion (1.38 nm particle size) to activate the hydrogen source, the moderate acid property to suppress carbon deposition and the abundant oxygen vacancy to promote substrate adsorption at the same time. 99.9% conversion of guaiacol is obtained at 230 °C, with 99.9% selectivity towards cyclohexane. Ru/CA‐2 catalyst also has a good recyclability, with no obvious activity loss after five runs. Furthermore, in the application of catalytic lignin‐oil HDO, the content of hydrocarbons increase from 10.69% to 95.71%, showing great potential on the industrial usage.

chemistry, multidisciplinary,green & sustainable science & technology
Hydrodeoxygenation of Lignin-derived Phenols into Cycloalkanes by Atomically Dispersed Pt-Polyoxometalate Catalysts

Xueying Gao,Rumin Ma,Zhenzhen Liu,Shuizhong Wang,Yulong Wu,Guoyong Song

DOI: https://doi.org/10.1016/j.apcatb.2024.124059

2024-01-01

Abstract:We report atomically dispersed Pt sites anchored on polyoxometalate cesium salts as robust and durable catalysts for upgrading lignin into hydrocarbons at relatively mild conditions. Experimental results and DFT calculations cross-validate the catalytic performance, considering the porosity, acidity, H2 storage capacity, and HOMO-LUMO energy gap of these catalysts. The optimal Pt0.4/CsPW-H2 catalyst enables the hydrodeoxygenation (HDO) of a diverse range of lignin-derived phenolics into hydrocarbons with up to 97% yield at the conditions of 150 °C and 0.1 to 2MPa H2. A lignin oil from the reductive catalytic fractionation (RCF) of Eucalyptus wood can be transformed into cyclohexanes with a 32.7wt% yield under a solvent-free condition. This catalyst demonstrates excellent reusability in the HDO of 4-propyl guaiacol for 20 cycles, achieving a 15095 molpropylcyclohexane molPt-1 total turnover number (TON). This work broadens the horizons of designing highly efficient catalytic systems aimed at sustainably producing liquid fuels from lignin.
Hydrodeoxygenation of lignin-derived phenolic compounds over Ru/TiO2 catalyst: Effect of TiO2 morphology

Zhuojie Zhong,Junxuan Li,Minyin Jian,Riyang Shu,Zhipeng Tian,Chao Wang,Ying Chen,Ning Shi,Yanxue Wu

DOI: https://doi.org/10.1016/j.fuel.2022.126241

IF: 7.4

2023-02-01

Fuel

Abstract:Hydrodeoxygenation (HDO) reaction is a necessary refinery process for lignin-derived phenolic compounds to be used as high quality liquid fuels. Catalyst morphology makes a big difference on the HDO performance through changing the properties of metal site and acid site, while the catalytic mechanism is still not very clear. In this work, four kinds of Ru/TiO2 catalysts with different morphology were prepared by photochemical method and all of them achieved a high Ru metal dispersion. A series of catalyst characterizations were carried out, including XRD, BET, SEM, TEM, H2-TPD and NH3-TPD, in order to explore the crystal structure, surface property, Ru metal dispersion, hydrogen adsorption capacity as well as acid properties. Results showed that Ru/TNP catalyst possessed a large surface area, an abundance of medium strength acid sites and a good hydrogen adsorption capacity. The HDO performances on lignin-derived phenolic compounds were also compared, in which Ru/TNP catalyst presented the best HDO performance. The guaiacol conversion and the selectivity of cyclohexane product were both close to 100 % at 250 °C under 1 MPa hydrogen pressure. Moreover, the content of hydrocarbons increased from 11.1 % to 60.8 % in the lignin-oil upgrading process.

energy & fuels,engineering, chemical
Catalytic hydrodeoxygenation of lignin-derived phenolic compounds with Ni-based aluminum phosphate catalyst

Yuankai Lin,Riyang Shu,Tao Yin,Zhipeng Tian,Chao Wang,Ying Xu

DOI: https://doi.org/10.1016/j.mcat.2024.114444

IF: 4.6

2024-08-20

Molecular Catalysis

Abstract:Lignin-derived products possess high carbon content and offer significant potential to be used as liquid fuels. However, they also contain high oxygen element and unstable functional groups. Hydrodeoxygenation (HDO) is an effective method for upgrading lignin-derived phenolic compounds to produce high-quality liquid biofuels. In this study, a series of Ni-based phosphate catalysts incorporating various metals (Al, Ce, La) were prepared and employed for the HDO of lignin-derived phenolic compounds. The results showed that Ni/AlPO 4 had the most efficient HDO performance, with guaiacol conversion of 99.9 % and cyclohexane selectivity of 91.1 % at the reaction temperature of 250 °C. Various catalyst characterization measurements were conducted to assess the impact of metal phosphate species on the crystallography, morphology, physicochemical characteristics and surface properties. Results indicated that Ni/AlPO 4 catalyst exhibited stronger acidity, smaller Ni particle sizes and larger specific surface area than other Ni-based phosphate catalysts. Based on the characterization results and experimental data, the corresponding HDO reaction pathways and mechanisms were also proposed. Ni/AlPO 4 catalyst was also applied to the HDO of various lignin-derived phenol compounds and achieved a good HDO effect. Moreover, the catalytic upgrading of lignin-oil was also carried out, and a high proportion of hydrocarbon products that increased from 16.0 % to 88.6 % was obtained. This Ni/AlPO 4 catalyst provides potential reference for the HDO application of lignin-derived phenolic compounds for the production of hydrocarbon liquid fuels.

chemistry, physical
Selective hydrodeoxygenation of lignin-derived phenolics to cycloalkanes over highly stable NiAl<sub>2</sub>O<sub>4</sub> spinel-supported bifunctional catalysts

Xing Zhang,Jingfeng Wu,Tian Li,Chengzhi Zhang,Lingjun Zhu,Shurong Wang

DOI: https://doi.org/10.1016/j.cej.2021/132181

IF: 15.1

2022-01-01

Chemical Engineering Journal

Abstract:Hydrodeoxygenation (HDO) of lignin-derived bio-oil offers a promising route for the production of advanced biofuels. However, the conventional HDO of lignin-derived bio-oil faces serious problems, such as low hydrocarbon yield and easy deactivation of catalysts. Herein, a novel reaction system consisting of a highly stable bifunctional catalyst (i.e., Ni-WOx/NiAl2O4) and a dodecane solvent was developed for the HDO of lignin-derived phenolics. The Ni-0 species, derived from NiWO4 precursors on the NiAl2O4, were of small crystallite size and high dispersion, together with the strong oxophilicity of W, thereby exhibiting high activity. The use of a highly stable NiAl2O4 spinel support and the replacement of common solid acid with more stable WOx for the cleavage of C-O bond accounted for excellent stability. The optimized 10Ni-15WO(x)/NiAl2O4 exhibited a high guaiacol conversion of 97.8% with a high cycloalkane yield of 83.8% under the optimum conditions (250 degrees C, 5 MPa H-2, and 4 h). Cycloalkanes with a high yield over 90% were also obtained by the HDO of other complex lignin-derived compounds. More importantly, the catalyst always retained its initial activity for the HDO of guaiacol in five runs, with negligible coke formation. Subsequently, the HDO behavior of the bio-oil obtained from walnut shell pyrolysis was also studied. The relative content of cycloalkanes in the products reached 44.3% after the reaction. This study highlights the prospect of a highly stable catalyst consisting of hydrogenation metal and oxophilic promoter, and dodecane solvent to enable efficient production of cycloalkanes from the HDO of lignin-derived phenolics.
Hydrodeoxygenation of Lignin‐Derived Monomers and Dimers over a Ru Supported Solid Super Acid Catalyst for Cycloalkane Production

Xing Zhang,Hui Yan,Lingjun Zhu,Tian Li,Shurong Wang

DOI: https://doi.org/10.1002/adsu.201900136

IF: 6.737

2020-01-01

Advanced Sustainable Systems

Abstract:The monomers and dimers produced via lignin depolymerization are a promising alternative to transportation fuels after hydrodeoxygenation (HDO). However, these compounds contain numerous oxygen‐containing functional groups that are strongly bonded to aromatic rings. Therefore, the conventional HDO of lignin‐derived compounds faces serious problems of catalyst deactivation due to coke deposition and low hydrocarbon yields. A metal–solid super acid catalyst, i.e., Ru(SO42−)/ZrO2–CeO2, is synthesized, characterized, and evaluated for the HDO of various lignin‐derived monomers and dimers in a biphasic n‐dodecane/H2O system. A high cyclohexane yield of 98.5% is obtained by the HDO of phenol performed at 200 °C and 5 MPa. The “hydrated” configuration can be formed between the hydrogenation intermediates and H2O on the Ru sites. In addition, the anionic vacancies of ZrO2–CeO2 can be occupied by H− derived from the heterolytic cleavage of H2, leading to the formation of metal hydrides. The strong acidity of SO42−/ZrO2–CeO2 is beneficial for the subsequent deoxygenation of the hydrotreated products. In addition, the biphasic system can minimize the side reactions induced by the strong acidity of the catalyst. The catalytic system also exhibits a good catalytic performance for the HDO of other lignin‐derived monomers and dimers to produce cycloalkanes.
Catalytic Hydrodeoxygenation of Lignin and Its Model Compounds to Hydrocarbon Fuels over a Metal/Acid Ru/HZSM-5 Catalyst

Wei Jiang,Jing-Pei Cao,Jin-Xuan Xie,Liang Zhao,Chuang Zhang,Xiao-Yan Zhao,Yun-Peng Zhao,Jian-Li Zhang

DOI: https://doi.org/10.1021/acs.energyfuels.1c03169

2021-11-18

Abstract:The hydrodeoxygenation (HDO) reaction represents an important process for the high-value utilization of lignin and its model compounds. Here, the Ru/HZSM-5 catalyst containing a large number of acid sites was prepared by an incipient wetness impregnation method. Diphenyl ether (DPE) as a typical model compound in lignin could be completely converted into cyclohexane over the Ru/HZSM-5 catalyst under mild conditions (210 °C, 1 MPa H2, and 2 h). The oxygen atoms in lignin and other model compounds could be also effectively removed via the HDO reaction catalyzed by Ru/HZSM-5 in this study. The coexistence of both the function of Ru metal for hydrogenolysis and acid sites in the pores of HZSM-5 for deoxidation was responsible for the entire HDO reaction. The structure–performance relationship of the Ru/HZSM-5 catalyst in the HDO was investigated and the reaction pathway for the HDO of DPE was analyzed.

energy & fuels,engineering, chemical
Hydrodeoxygenation of lignin-derived phenolics to cycloalkanes over Ni-Co alloy coupled with oxophilic NbOx

Chengzhi Zhang,Xing Zhang,Jingfeng Wu,Lingjun Zhu,Shurong Wang

DOI: https://doi.org/10.1016/j.apenergy.2022.120199

IF: 11.2

2022-01-01

Applied Energy

Abstract:Hydrodeoxygenation (HDO) of lignin-derived bio-oil is a promising route to produce advanced biofuels. How-ever, the removal of oxygen-containing functional groups with high bond strength in bio-oil challenges the development of efficient, stable, and inexpensive catalysts. In this study, a series of bifunctional catalysts were synthesized by coupling Ni-Co alloy with an oxophilic NbOx support, which was used for the HDO of lignin -derived phenolics to produce cycloalkanes. The Ni-Co alloy formed on the bimetallic catalysts during calcina-tion and reduction was verified by TEM, XPS, and H2-TPR measurements, which showed excellent hydro-genolysis activity. The composition of the Ni-Co alloy was the most uniform with a Ni/Co molar ratio of 1, and the catalyst achieved the highest catalytic activity. The oxygen vacancies provided by the NbOx support also enhanced the adsorption of phenolics and promoted the removal of oxygen-containing functional groups by forming a specific configuration. The synergistic catalysis of Ni-Co alloy and oxygen vacancies achieved com-plete conversion of guaiacol with a high cycloalkane selectivity of 98.9 % under optimal conditions (300 degrees C, 3 MPa H2, and 2 h). More importantly, only marginal deactivation occurred on the 5Ni-5Co/NbOx catalyst after 5 cycles and it was also successfully applied to the efficient conversion of other complex lignin-derived phenolics. Therefore, an efficient and economical strategy of coupling the Ni-Co alloy with an oxophilic NbOx support to catalyze the HDO of lignin-derived phenolics to produce cycloalkanes was prospective.
Synergistic effect of active metal–acid sites on hydrodeoxygenation of lignin-derived phenolic compounds under mild conditions using Ru/C-HPW catalyst

Zhi Yang,Bowen Luo,Riyang Shu,Zhuojie Zhong,Zhipeng Tian,Chao Wang,Ying Chen

DOI: https://doi.org/10.1016/j.fuel.2022.123617

IF: 7.4

2022-07-01

Fuel

Abstract:Hydrodeoxygenation (HDO) is an indispensable reaction in the field of fuel and chemical production, and the synergistic effect of metal–acid sites in the catalyst makes great influence to it. Herein, a bifunctional catalyst of Ru/C combined with phosphotungstic acid (HPW) was employed for the hydrodeoxygenation (HDO) of lignin-derived compounds to make full use of the synergistic effect of active metal–acid sites. HPW possessed a temperature-controlled phase-transfer behavior, which made it dispersed well on the surface of Ru/C catalyst and resulted in a close integration of acid site with metal site. Ru/C-HPW catalyst also owned the advantage of high reaction rate and good recyclability, which exhibited no obvious catalytic activity loss after 5 runs. Lignin-derived phenolic compounds including monomers and dimers enabled to obtain an efficient transformation to cycloalkanes at the temperature of 200 °C. Moreover, a high HDO reaction efficiency of raw lignin-oil was also observed in this study, with the increasing hydrocarbon content from 5.5% to 78.9%. This novel catalytic system can achieve a high HDO efficiency under mild conditions.

energy & fuels,engineering, chemical
Selective hydrodeoxygenation of lignin-derived phenols to alkyl cyclohexanols over highly dispersed RuFe bimetallic catalysts

Tao Liu,Zhipeng Tian,Weijie Zhang,Bowen Luo,Libin Lei,Chao Wang,Jianping Liu,Riyang Shu,Ying Chen

DOI: https://doi.org/10.1016/j.fuel.2022.126916

IF: 7.4

2023-05-01

Fuel

Abstract:Selective hydrodeoxygenation (HDO) of phenolic compounds derived from the pyrolysis lignin-oil to desired products is a promising route in the high-value utilization of biomass-derived products. Cyclohexanol, as one of the important chemical materials, is an intermediate of catalytic HDO of guaiacol. Controllable selective HDO is conducted to improve the cyclohexanol selectivity over RuFe bimetallic catalyst prepared by ethylene glycol reduction method in this work. 99.99% guaiacol conversion and 81.35% cyclohexanol selectivity are obtained over optimized 2Ru2.5Fe/Al2O3-EG catalyst, which is better than those over 2Ru/Al2O3-EG catalyst. The mild catalyst preparation method gives it a high dispersion and uniform distribution of Ru and Fe species on the support. Various characterizations have proved that the intimate contact between Ru and Fe2O3 species contributes to the improvement of cyclohexanol selectivity. Partial blockage of Ru sites by Fe2O3 species slightly reduces the hydrogen adsorption capacity while the addition of Fe helps enhancing the hydrogenolysis of C-OMe bond. The reciprocal effect facilitates the removal of methoxyl groups and hinders the dehydroxylation of cyclohexanol to cyclohexane. Besides, other phenolic compounds and pyrolysis lignin-oil as substrates also show good selective HDO reactivity to corresponding alkyl cyclohexanols, implying potential application in the transformation from lignin-oil to high-value products.

energy & fuels,engineering, chemical
Gas-phase catalytic hydrodeoxygenation of phenolic compounds derived from lignin pyrolysis for hydrocarbon production using Ni@HZSM-5-γ-Al2O3

Jinliang Yan,Rundong Liu,Zhiyu Li,Peng Fu,Ping Geng,Weiming Yi

DOI: https://doi.org/10.1016/j.jaap.2022.105626

IF: 6

2022-09-01

Journal of Analytical and Applied Pyrolysis

Abstract:The bio-oils derived from fast pyrolysis of lignin contain large amount of phenolic components. Due to its high oxygen content, it cannot be used directly as traffic liquid fuels. Currently, hydrodeoxygenation (HDO) is an effective method for upgrading bio-oil to produce high-quality liquid fuels. However, catalysts have a key role in the selective hydrogenolysis of oxygen-containing groups (e.g. -OCH3). In this study, the mixed supported nickel-based catalyst Ni@HZSM-5-γ-Al2O3 was successfully prepared by the impregnation method. The influence of the temperature, pressure, hydrogen flow rate and weight hourly space velocity (WHSV) on the HDO activity was investigated. Under the optimized conditions (350 °C, 15 bar, 350 mL/min H2, 1 h−1), the conversion of guaiacol reached 98.73%, and the product liquid yields and hydrocarbon contents were 39.82% and 86.85%, respectively. In particular, the contents of aromatics and alkanes were 49.60% and 37.25%, respectively. Based on catalyst evaluation and characterization, the mechanism of guaiacol HDO was explored. Demethylation, direct deoxygenation, hydrogenation, hydrolysis, transalkylation and condensation reactions were considered as the main pathways.

engineering, chemical,chemistry, analytical,energy & fuels
Hydrodeoxygenation of lignin bio-oil model compounds and surrogate mixtures over zeolite supported nickel catalysts

Foteini F. Zormpa,Antigoni G. Margellou,Stamatia A. Karakoulia,Evangelia Delli,Konstantinos S. Triantafyllidis

DOI: https://doi.org/10.1016/j.cattod.2024.114654

IF: 5.3

2024-03-23

Catalysis Today

Abstract:Bifunctional catalysts based on nickel supported on ZSM-5 and BETA zeolites were studied in the hydrodeoxygenation of lignin derived model compounds as well as in surrogate mixtures simulating the light fraction of lignin fast pyrolysis bio-oil. A screening of the hydrodeoxygenation reaction conditions (temperature, time, H 2 pressure, catalyst amount) was carried out using the simplest phenolic compound, phenol. As in real lignin bio-oils more complex phenolic compounds are present, a series of relevant alkyl- and methoxy-substituted phenol and benzene (o- and m-cresol, catechol, anisole, guaiacol, syringol, creosol and 1,2,3-trimethoxybenzene) were also investigated as feedstocks. Furthermore, the effect of the different porous and acidic properties of the zeolitic supports was investigated in the hydrodeoxygenation of guaiacol. The conversion of the model phenolics and the yield of the respective (alkyl)cyclohexanes at relatively mild conditions (220 o C, 50 bar H 2 , 1 h) were in the range of 80-100% and 47-83%, respectively, being dependent mainly on the complexity/side-chain group of the phenolic/benzylic ring and on the balanced content of Brønsted acid sites of increased strength. Regarding the hydrodeoxygenation of the surrogate mixture (C 7 -C 10 phenolics), 100% hydrodeoxygenation efficiency was achieved towards >60% yield of (alkyl)cyclohexanes (C 6 -C 9 hydrocarbons). All hydrodeoxygenation tests were conducted in hexadecane as solvent/substrate in order to simulate model co-processing (i.e. bio-based phenolics with petroleum derived feedstocks) conditions. Reusability tests revealed the stability of the catalysts which showed partial (30%) deactivation after the third catalytic cycle.

chemistry, physical,engineering, chemical, applied
Bifunctional and Bimetallic Pt–Ru/HZSM-5 Nanoparticles for the Mild Hydrodeoxygenation of Lignin-Derived 4-Propylphenol

Saros Salakhum,Thittaya Yutthalekha,Sirawit Shetsiri,Thongthai Witoon,Chularat Wattanakit

DOI: https://doi.org/10.1021/acsanm.8b02324

IF: 6.14

2019-01-25

ACS Applied Nano Materials

Abstract:The development of bifunctional and bimetallic catalysts is of crucial importance for the bio-oils upgrading applications. To improve the quality of bio-oils as fuels, hydrodeoxygenation (HDO) is one of the most promising reactions for the upgrading of lignin-derived bio-oils. However, this process has been typically operated under high H2 pressures (40–50 atm). Therefore, the development of catalysts for the HDO of lignin-derived compounds operated under mild conditions is still a great challenge. In this context, the mild HDO of 4-propylphenol as a model bio-oil compound operated at atmospheric pressure using hierarchical bimetallic Pt–Ru/HZSM-5, prepared by co-impregnation of metals on zeolite nanoparticles obtained by a one-pot hydrothermal synthesis with the aid of tetrabutylphosphonium hydroxide as a dual structure-directing agent, is reported. The combination of Pt and Ru together with hierarchical structures of zeolites eventually results in the unexpectedly excellent catalytic performance toward the alkylcycloalkane production. Not only the presence of hierarchical structure provides the beneficial effect for promoting the high dispersibility of bimetallic active sites, eventually leading to a significant decrease in the nanometallic particle size (20.0 ± 8.0 to 2.7 ± 0.6 nm over conventional zeolite and hierarchical one, respectively), but also the synergistic effect of bimetallic Pt and Ru active sites can greatly enhance a very high yield of propylcyclohexane (100%). The synergistic bifunctional and bimetallic catalytic platform illustrates scientific opportunities toward bio-oil upgrading applications.

materials science, multidisciplinary,nanoscience & nanotechnology
Mild hydrodeoxygenation of lignin-derived bio-oils to hydrocarbons over bifunctional ZrP2O7-Ni12P5 catalysts

Bo Chen,Ruiheng Rao,Meifang Cao,Chengzhi He,Yong Qian,Xueqing Qiu,Xinping Ouyang

DOI: https://doi.org/10.1016/j.fuel.2021.123044

IF: 7.4

2022-04-01

Fuel

Abstract:An imperative current challenge for the production of renewable fuels is the development of efficient catalytic hydrodeoxygenation (HDO) of phenolic-rich bio-oils into hydrocarbons. In this work, a series of bifunctional ZrP2O7(x)-Ni12P5 (where × represents the molar ratio of Zr/Ni in the catalysts) catalysts were prepared for HDO of lignin-derived bio-oils (LBO). The characterization results show that among these bimetallic catalysts, ZrP2O7(0.4)-Ni12P5 possesses the largest specific surface area, pore volume and the highest amount of acid sites (Lewis and Brønsted) due to the introduction of appropriate amount of Zr species. Meanwhile, the interaction between Niδ+ and Zr species on its surface creates new active sites for the promotion on the hydrogen adsorption and activation, thus endowing the most excellent catalytic performance. Using the optimized catalyst of ZrP2O7(0.4)-Ni12P5, 95.8% cyclohexane yield could be obtained from the HDO of guaiacol as a model compound from bio-oil under mild condition (3 MPa H2 and 250 ℃). Moreover, 36.1% hydrocarbon yield is achieved from HDO of lignin-derived bio-oils (LBO) under the same hydrogen pressure and temperature. These findings not only open a novel avenue for designing a cost-effective metal–acid bifunctional catalyst, but also provide a viable approach for converting lignocellulosic biomass feedstocks into valuable hydrocarbons.

energy & fuels,engineering, chemical

Hydrodeoxygenation of Lignin-Derived Phenols into Alkanes over Carbon Nanotube Supported Ru Catalysts in Biphasic Systems

Aqueous Phase Partial Hydrodeoxygenation of Lignin-Derived Phenols over Al2o3-Sio2 Microspheres Supported Rumn Multifunctional Catalyst: Synergic Effect among Ru, Mn and Al2o3-Sio2 Support

Hydrogenolysis and Hydrodeoxygenation of Lignin in a Two-Step Process to Produce Hydrocarbons and Alkylphenols

A Review on the Catalytic Hydrodeoxygenation of Lignin-Derived Phenolic Compounds and the Conversion of Raw Lignin to Hydrocarbon Liquid Fuels

One-pot Hydrodeoxygenation (HDO) of Lignin Monomers to C9 Hydrocarbons Co-Catalysed by Ru/C and Nb2O5

Water-assisted selective hydrodeoxygenation of phenol to benzene over the Ru composite catalyst in the biphasic process

Efficient Hydrodeoxygenation of Lignin-Derived Phenols to C6+Cycloalkanols/Cycloalkanes over Magnetic Carbon-Encapsulated Nickel Nanospheres

Efficient Hydrodeoxygenation of Lignin‐derived Phenolic Compounds over Ru‐based Catalyst with Biochar and Al2O3 as Composite Support

Hydrodeoxygenation of Lignin-derived Phenols into Cycloalkanes by Atomically Dispersed Pt-Polyoxometalate Catalysts

Hydrodeoxygenation of lignin-derived phenolic compounds over Ru/TiO2 catalyst: Effect of TiO2 morphology

Catalytic hydrodeoxygenation of lignin-derived phenolic compounds with Ni-based aluminum phosphate catalyst

Selective hydrodeoxygenation of lignin-derived phenolics to cycloalkanes over highly stable NiAl<sub>2</sub>O<sub>4</sub> spinel-supported bifunctional catalysts

Hydrodeoxygenation of Lignin‐Derived Monomers and Dimers over a Ru Supported Solid Super Acid Catalyst for Cycloalkane Production

Catalytic Hydrodeoxygenation of Lignin and Its Model Compounds to Hydrocarbon Fuels over a Metal/Acid Ru/HZSM-5 Catalyst

Hydrodeoxygenation of lignin-derived phenolics to cycloalkanes over Ni-Co alloy coupled with oxophilic NbOx

Synergistic effect of active metal–acid sites on hydrodeoxygenation of lignin-derived phenolic compounds under mild conditions using Ru/C-HPW catalyst

Selective hydrodeoxygenation of lignin-derived phenols to alkyl cyclohexanols over highly dispersed RuFe bimetallic catalysts

Gas-phase catalytic hydrodeoxygenation of phenolic compounds derived from lignin pyrolysis for hydrocarbon production using Ni@HZSM-5-γ-Al2O3

Hydrodeoxygenation of lignin bio-oil model compounds and surrogate mixtures over zeolite supported nickel catalysts

Bifunctional and Bimetallic Pt–Ru/HZSM-5 Nanoparticles for the Mild Hydrodeoxygenation of Lignin-Derived 4-Propylphenol

Mild hydrodeoxygenation of lignin-derived bio-oils to hydrocarbons over bifunctional ZrP2O7-Ni12P5 catalysts