Abstract:The onset of pitting on high purity and ultra high purity aluminum has been studied in the micrometer range by using a microelectrochemical cell in order to evaluate influences that induce localized corrosion. Microelectrochemical tests on polished samples of Al 99.999 and Al 99.9999 in 1 M NaCl showed that pitting at large areas occurred at several hundreds mV more negative than at small areas, suggesting that even very pure Al contains weak points. On rough surfaces weak points are more “activated” than on smooth surfaces. Locally measured pitting potentials of polished samples were shifted to more positive values than those measured on ground samples. Larger areas contain always small scratches, even on polished samples. Hence, the surface roughness showed a minor influence on the onset of pitting on larger areas. Microelectrochemical measurements performed on pure Al 99.99 with small amounts of copper showed that a copper content below 30 ppm is too small to have a beneficial or detrimental effect, whereas a copper content above 300 ppm probably leads to the formation of small inclusions or precipitations that acted as preferential corrosion initiation sites. A copper content around 100 ppm showed a beneficial effect on very small areas but not on larger ones. The onset of pitting on high purity and ultra high purity aluminum has been studied in the micrometer range by using a microelectrochemical cell in order to evaluate influences that induce localized corrosion. In 1 M NaCl we tested the influence of the surface roughness, of the size of the exposed area , and of small amounts of alloyed copper.

The Reliability of Electrochemical Noise and Current Transients Characterizing Metastable Pitting of Al–Mg–Si Microelectrodes

Detection and Analysis of Anodic Current Transients Associated with Nanoscale Β-Phase Precipitates on an Al–Mg Microelectrode

Electrochemical noises of LC4, LY12 and pure Al in NaCl solution

In-situ monitoring of pitting corrosion of Q235 carbon steel by electrochemical noise: Wavelet and recurrence quantification analysis

The Electrochemical and Morphological Characteristics of Single Metastable Pit for 304 Stainless Steel under Potentiostatic Polarization

Electrochemical noise features of pure aluminum during pitting corrosion in neutral NaCl solution

Study of Pitting Corrosion on Mild Steel During Wet–dry Cycles by Electrochemical Noise Analysis Based on Chaos Theory

Potentiostatic Electrochemical Noise Analysis of 2101 Lean Duplex Stainless Steel in 1 mol/L NaCl

Electrochemical noise comparative study of pitting corrosion of 316L stainless steel fabricated by selective laser melting and wrought

Features of Electrochemical Noise During Pitting Corrosion of 2024-T3 Aluminum Alloy in 3.0% Na2SO4 Solution

Analysis of Pitting Corrosion Behavior of Pure Al in Sodium Chloride Solution with the Wavelet Technique

In-situ monitoring of pitting corrosion of AZ31 magnesium alloy by combining electrochemical noise and acoustic emission techniques

Influence of Aging Treatment on the Pitting Behavior Associated with the Dissolution of Active Nanoscale Β-Phase Precipitates for an Al–Mg Alloy

Current Instability for Silicon Nanowire Field-Effect Sensors Operating in Electrolyte with Platinum Gate Electrodes

ELECTROCHEMICAL NOISE OF AZ31 MAGNESIUM ALLOY IN NaCI SOLUTION

ELECTROCHEMICAL FEATURES OF THE CORROSION OF AN ALUMINUM-LITHIUM ALLOY IN 3.0% NaCl SOLUTION

Microelectrochemical Studies of Pit Initiation on High Purity and Ultra High Purity Aluminum

Exfoliation Corrosion of Al-Li Alloy 2090-T6 in Exco Solution: A Study of Electrochemical Noise and Electrochemical Impedance Spectroscopy

Investigation on the Transient Current Response to Potential Pulse for an Electrochemical System with High Impedence

Pitting Corrosion Behavior of Stainless Steel in Ultrasonic Cell

In-situ Monitoring of Nickel Electrodeposit Structure Using Electrochemical Noise Technique