Abstract:The mechanical behavior of a commercially pure titanium (CP-Ti) is systematically investigated in quasi-static (Instron, servohydraulic) and dynamic (UCSD's recovery Hopkinson) compression. Strains over 40% are achieved in these tests over a temperature range of 77–1000K and strain rates of 10−3–8000/s. At the macroscopic level, the flow stress of CP-Ti, within the plastic deformation regime, is strongly dependent on the temperature and strain rate, and displays complex variations with strain, strain rate, and temperature. In particular, there is a three-stage deformation pattern at a temperature range from 296 to 800K, the specific range depending on the strain rate. In an effort to understand the underlying mechanisms, a number of interrupted tests involving temperature jumps are performed, and the resulting microstructures are characterized using an optical microscope. Based on the experimental results and simple estimates, it is concluded that the three-stage pattern of deformation at temperatures from 296 to 800K, is a result of dynamic strain aging, through the directional diffusion of dislocation-core point defects with the moving dislocation at high strain rates, although the usual dynamic strain aging by point defects segregating outside the dislocation core through volume diffusion is also observed at low strain rates and high temperatures. The microscopic analysis shows that there is substantial deformation twinning which cannot be neglected in modeling the plastic flow of CP-Ti. The density of twins increases markedly with increasing strain rate, strain, and decreasing temperature. Twin intersections occur, and become more pronounced at low temperatures or high strain rates. In sum, the true stress–true strain curves of CP-Ti show two stages of deformation pattern at low temperatures, three stages at temperatures above 296K, and only one stage at temperatures exceeding 800K, although all three stages may exist even at 1000K for very high strain rates, e.g. 8000/s. While the dislocation motion is still the main deformation mechanism for plastic flow, the experimental results suggest that dynamic strain aging should be taken into account, as well as the effect of deformation twinning.

Microhardness Evolution and Mechanical Characteristics of Commercial Purity Titanium Processed by High-Pressure Torsion

Thermal Stability of Ultrafine-Grained Pure Titanium Processed by High-Pressure Torsion

Microstructural Behavior and Mechanical Properties of Nanocrystalline Ti-22Al-25Nb Alloy Processed by High-Pressure Torsion

Properties of Commercial Pure Titanium under Self-Heating and High-Pressure Heating Treatment

Effect of high pressure torsion process on the microhardness, microstructure and tribological property of Ti6Al4V alloy

Mechanical properties and deformation mechanisms of a commercially pure titanium

The Evolvement of Mechanical Properties and Microstructure of Commercial Aluminum Alloy 6061 via High-Pressure Torsion

Influence of high-pressure torsion on mechanical properties and microstructural evolution in 2197 Al-Li alloy

Microhardness and Microstructural Evolution of Pure Nickel Processed by High-Pressure Torsion

Microstructural evolution and mechanical properties of biomedical Co-Cr-Mo alloy subjected to high-pressure torsion

Strength enhancement of an aluminum alloy through high pressure torsion

Microhardness, Microstructure and Tensile Behavior of an AZ31 Magnesium Alloy Processed by High-Pressure Torsion

Experimental Study on Microstructure and Hardness of Pure Titanium Subjected to Torsion Deformation at Different Temperatures

Microstructural Evolution of Mg-4nd Alloy Processed by High-Pressure Torsion

Materials Science Forum

Effect of composition, annealing temperature, and high pressure torsion on structure and hardness of Ti–V and Ti–V–Al alloys

Evolution of Microstructure and Mechanical Properties of an As-Cast Mg-8.2gd-3.8y-1.0zn-0.4zr Alloy Processed by High Pressure Torsion

The effect of high pressure torsion on structural refinement and mechanical properties of an austenitic stainless steel

Effect of High-Pressure Torsion on Phase Formation and Mechanical Properties of a High-Entropy TiZrHfMoCrCo Alloy

Microstructure and Property Evolution of Al-0.4Fe-0.15Zr-0.25Er Alloy Processed by High Pressure Torsion

Microstructural Evolution and Mechanical Properties in Superlight Mg-Li Alloy Processed by High-Pressure Torsion