Abstract:A thermoplastic vulcanizate (TPV) of a ethylene-propylene-diene terpolymer (EPDM) and nylon copolymer (PA) was prepared by dynamic vulcanization. Maleic anhydride (MAH)-grafted EPDM (EPDM-g-MAH), MAH-grafted EPR (EPR-g-MAH), and chlorinated polyethylene (CPE) were used as compatibilizers. The effect of dynamic vulcanization and compatibilizer on the crystallization behavior of PA was investigated. Differential scanning calorimeter measurement results showed no pronounced shift in the crystallization temperature for PA in EPDM-PA TPV compared to that for PA in the neat state, whereas the crystallization temperature increased after adding compatibilizer. The decrease in the crystallinity of TPVs was a result of the crystallization occurring in confined spaces between rubber particles. The equilibrium melting temperature (Tm-0) of the PA copolymer was measured and was determined to be 157degreesC. The isothermal crystallization kinetics of PA in the neat and TPV states also was investigated. The crystallization rate was highest in the compatibilized TPV and lowest in the neat PA, whereas it was intermediate in the uncompatibilized TPV unvulcanized blends. Compared with unvulcanized EPDM-PA blends, the dynamic vulcanization process seemed to cause an obvious increase in the crystallization rate of the PA copolymer, especially when a suitable compatibilizer was used. This occurred because the dynamic vulcanization introduced fine crosslinked rubber particles that could act as heterogeneous nucleating centers. In addition, the use of a suitable compatibilizer permitted the formation of finely dispersed vulcanized rubber particles and therefore increased the density of the nucleating centers. The complex morphology of the blends was investigated by atomic force microscopy to evaluate the effect of compatibilizer on the size of the dispersed rubber particles. Compared with the morphology of TPVs with the same dosage of EPDM-g-MAH compatibilizer, the morphology of TPVs using EPR-g-MAH as compatibilizer showed much smaller dispersed rubber particles, which may have contributed to the higher crystallization rate. (C) 2003 Wiley Periodicals, Inc.

Phase Morphologies of Vulcanized Chlorobutyl Rubber/polyamide 12 Blends: the Breakup of Pre‐crosslinked CIIR Phase

Phase inversion during bulk copolymerization of N-phenylmaleimide/styrene in presence of polybutadiene (II): Effects of operation conditions and recipes on occurrence of phase inversion and structure of rubber phase

Polybutadiene Vitrimers with Tunable Epoxy Ratios: Preparation and Properties

Viscoelastic Effects on the Phase Separation in Thermoplastics Modified Cyanate Ester Resin

New Understanding of Microstructure Formation of the Rubber Phase in Thermoplastic Vulcanizates (TPV)

Properties and Unique Morphological Evolution of Dynamically Vulcanized Bromo-Isobutylene-isoprene Rubber/polypropylene Thermoplastic Elastomer

Study on the Microstructure and Properties of Bromobutyl Rubber (biir)/polyamide‐12 (PA12) Thermoplastic Vulcanizates (Tpvs)

Regulation effects of trans-1, 4-poly (isoprene-co-butadiene) copolymer on the processability, aggregation structure and properties of chloroprene rubber

Observation of morphology in EPDM/nylon copolymer thermoplastic vulcanizates by atomic force microscopy

Effect of compatibilizers on dynamic vulcanized chlorinated butyl rubber/polyamide 12 thermoplastic elastomers

Morphological structure of dynamically vulcanized thermoplastic elastomer of ethylene propylene diene monomer/polypropylene

Influence factors on preparation and properties of dynamic vulcanized brominated butyl rubber/polypropylene thermoplastic elastomer

Crosslink Network Evolution of BIIR/EPDM Blends During Peroxide Vulcanization

Effect of Additives on the Morphology Evolution of EPDM/PP TPVs During Dynamic Vulcanization in a Twin-Screw Extruder

Investigation of crystallization behavior in dynamically vulcanized EPDM-nylon copolymer blends

Theoretical and Experimental Insights into the Phase Transition of Rubber/Plastic Blends During Dynamic Vulcanization

Dependence of microstructure and properties of polypropylene/bromo‐isobutylene‐isoprene rubber thermoplastic vulcanizates on the molding process

Phase Separation of Impact‐modified PVC/PMMA Blends under Melt‐blending Conditions

A Rubber-Modified Thermoplastic where the Morphology Produced by Phase-Separation Induced by Polymerization Disappears at High Conversions

Effect of Curing Systems on Properties of Chlorinated Butyl Rubber/nylon 12 Dynamic Vulcanizates

Coupling Effect of Molecular Weight and Crosslinking Kinetics on the Formation of Rubber Nanoparticles and Their Agglomerates in EPDM/PP TPVs During Dynamic Vulcanization.