Abstract:Phase separation kinetics of polyethylene copolymer blends polyethylene-co-hexene (PEH)/polyethylene-co-butene (PEB) at a phase separation temperature of 130 degrees C have been investigated through the combination of rheological measurements and optical microscope observation. When the blends are located in the unstable region, i.e., PEH/PEB 40/60 blend (H40), 50/50 blend (H50), and 60/40 blend (H60), due to the coeffect of the fast decay of concentration fluctuations and the reduced interfacial area, the stroage modulus, G', behaves dramatically, decreasing at the early or intermediate stages; while when the blends are located in the metastable region, i.e., PEH/PEB 70/30 blend (H70), G' decreases slightly and slowly during the whole time sweep process. During the cyclic frequency sweeps, G' evolutions of H50 and H70 show similar trends. Obviously different from the strong phase segregation systems, the increase of G' with time in the metastable region has not been observed, possibly due to the entanglement effects and weak interaction between the components of polyethylene blends. The interfacial tension-driven or diffusion-limited morphological evolutions of H50 and H70 during phase separation give direct interpretations to the viscoelastic difference between the two blends, which is dominated by different phase separation kinetics. The relatively low interfacial tensions at the late stage of phase separation for H50 (0.5-0.38 mN/m varying with time) and H70 (1.2 mN/m) can be estimated by using the Gramespacher-Meissner model.

Viscoelastic Effects on the Phase Separation in Thermoplastics Modified Cyanate Ester Resin

Viscoelastic Effects on the Phase Separation in Thermoplastics-Modified Epoxy Resin

Studies on the Phase Separation of Poly(Ether Imide)‐Modified Cyanate Ester Resin

Effect Of Polyethersulfone On The Mechanical And Rheological Properties Of Polyetherimide-Modified Epoxy Systems

Morphology and mechanical properties of poly(ether-imide)-modified polycyanurates

Polymerization-induced viscoelastic phase separation in polyethersulfone-modified epoxy systems.

Polymerization Induced Phase Separation in Poly(ether Imide)-Modified Epoxy Resin Cured with Imidazole

Kinetics of Phase Separation at the Early Stage of Spinodal Decomposition in Epoxy Resin Modified with PEI Blends

Further Study of the Viscoelastic Phase Separation of Cyanate Ester Modified with Poly(ether Imide)

Rheological Behaviors and Structural Transitions in A Polyethersulfone-Modified Epoxy System During Phase Separation

Morphology Evolution During the Phase Separation of Polyetherimide/Epoxy Blends

Study on the Polyethersulfone/bismaleimide Blends: Morphology and Rheology During Isothermal Curing

Effects of the Molecular Weight of Poly(ether Imide) on the Viscoelastic Phase Separation of Poly(ether Imide)/epoxy Blends

Viscoelastic phase separation in polyethersulfone modified bismaleimide resin

Studies on the viscoelastic phase separation in epoxy resin modified with polyethersulfone

Studies on the Phase Separation of a Polyetherimide-Modified Epoxy Resin, 4. Kinetic Effect on the Phase Separation Mechanism of a Blend at Different Cure Rates

Investigation on Phase Separation Kinetics of Polyolefin Blends Through Combination of Viscoelasticity and Morphology.

Studies on the Phase Separation of Polyetherimide-Modified Epoxy Resin, 3. Morphology Development of the Blend During Curing

Study on the phase separation of thermoplastic‐modified epoxy systems by time‐resolved small‐angle laser light scattering

Studies on the phase separation of polyetherimide-modified epoxy resin, 3 - Part 1 - Morphology development of the blend during curing

Studies on the Phase Separation of Polyetherimide‐modified Epoxy Resin, 2. Effect of Molecular Weight of PEI on the Structure Formation