Abstract:Abstract Thermoplastic elastomers are rubbery materials which can be fabricated by techniques usually associated with thermoplastic resins. Classical elastomers rely upon the crosslinked network, developed during vulcanization, to provide the retractive forces of rubber type elasticity. Thermoplastic elastomers contain rubber domains and resinous thermoplastic domains. The thermoplasticity results from the melting characteristics of the hard thermoplastic phase, while the rubber properties arise from the rubbery domains. Thermoplastic elastomers are, therefore, almost by definition, heterogeneous in their phase morphology. Such materials can be blends or block polymers. In the case of block polymers, the rubbery phase is not crosslinked chemically. However, hard or resinous phase domains occur as the hard segments of the block polymer which separate from the composition by agglomeration during cooling from the molten state. These domains act both as well-bonded reinforcing filler particles and as crosslinks. This is, of course, because the hard blocks are connected to the soft or rubbery segments by primary chemical bonds. In the case of the blend compositions, the hard and soft domains are separate polymeric species. However, there must be some form of interaction between the domains if useful properties are to be realized. Recently, uncured or partially cured EPDM rubber has been blended with polyolefin resin to make thermoplastic elastomer-like compositions. However, these compositions suffer deficiencies in performance as well as in certain aspects of fabricability. Only poor to fair performance at temperatures above 70°C in air or in oil has been achieved with the uncured to partially cured compositions. More recently, it has been found in our laboratories that fully cured EPDM compositions which are fabricable as thermoplastics can be prepared. Such compositions, referred to here as thermoplastic vulcanizates, have superior strength, high-temperature mechanical properties, hot oil and solvent resistance, better compression set, etc. This report outlines critical parameters associated with these unique materials.

A Rubber-Modified Thermoplastic where the Morphology Produced by Phase-Separation Induced by Polymerization Disappears at High Conversions

Phase inversion during bulk copolymerization of N-phenylmaleimide/styrene in presence of polybutadiene (II): Effects of operation conditions and recipes on occurrence of phase inversion and structure of rubber phase

Polybutadiene Vitrimers with Tunable Epoxy Ratios: Preparation and Properties

Viscoelastic Effects on the Phase Separation in Thermoplastics-Modified Epoxy Resin

Analysis of the Phase Separation Induced by a Free-Radical Polymerization in Solutions of Polyisobutylene in Isobornyl Methacrylate

Phase morphology, mechanical, and thermal properties of fiber-reinforced thermoplastic elastomer: Effects of blend composition and compatibilization

Morphology and properties of high molecular weight polyisobutylene and thermoplastic polyurethane elastomer

Polymerization-Induced Bimodal Phase Separation in A Rubber-Modified Epoxy System

Thermoplastic elastomer obtained by photopolymerization‐induced concomitant macrophase and microphase separations

Kinetics of the Free-Radical Polymerization of Isobornyl Methacrylate in the Presence of Polyisobutylenes of Different Molar Masses

Regulation effects of trans-1, 4-poly (isoprene-co-butadiene) copolymer on the processability, aggregation structure and properties of chloroprene rubber

The dynamics of montmorillonite clay dispersion and morphology development in immiscible ethylene–propylene rubber/polypropylene blends

Novel butadiene/isoprene copolymer with predominant 1,2/3,4-units: A tough thermoplastic elastomer material with superior dynamic mechanical properties

The Progress in the Research on Polymerization-induced Phase Separation of Thermoplastic Resin Modified Thermoset Resin

Phase morphology of nascent impact polypropylene copolymer and its evolution in the melt

Organosolv Lignin Improved Thermoplastic Elastomeric Behavior of Polyethylene/Polyisoprene Blend

Dependence of microstructure and properties of polypropylene/bromo‐isobutylene‐isoprene rubber thermoplastic vulcanizates on the molding process

Gelation Behavior of Thermoplastic-Modified Epoxy Systems During Polymerization-Induced Phase Separation

Rubber-Thermoplastic Compositions. Part I. EPDM-Polypropylene Thermoplastic Vulcanizates

Crystallization-driven Microstructure Changes During Microphase Separation for Environment-Friendly Thermoplastic Triblock Copolymer Elastomers

A novel elastomer/liquid crystal polymer nanocomposite created in situ from controlled radical graft-polymerization.