Abstract:Wood delignification can provide a wood-based template with sufficient pore volume for polymer/wood composites. At the same time, delignification is conducive to the penetration of polymer into the wood cell wall, which is of great significance to improve the function and performance of composites. However, lignin is the main chemical component in wood. The removal of lignin will inevitably lead to the change of the wood's physical properties, including the hygroscopicity of the wood. In this study, prepolymerized methyl methacrylate (MMA) impregnated delignified wood (DW) was used to obtain polymerized methyl methacrylate/delignified wood (PMMA/DW) composites with different lignin removal. The effect of lignin removal on the hygroscopicity of the composites is discussed. The results of nitrogen adsorption showed that the DW could adsorb more nitrogen than the original wood, and the amount of nitrogen adsorption gradually increased with the improvement of the processing degree. After filling with PMMA, the adsorption amount of nitrogen was greatly reduced. The results of the BET analysis showed that delignification promoted the distribution of PMMA in the pores of the wood cell wall. When lignin was almost completely removed, all mesopores in the cell wall were filled with PMMA. The results of the moisture absorption analysis isotherm curve showed that the moisture absorption content of the wood was positively correlated with the amount of lignin removed, and the moisture absorption content of the PMMA/DW composite was negatively correlated with the amount of lignin removed. The hygroscopic data were further analyzed using the Hailwood–Horrobin model. The results showed that the mole number of adsorbable or hydratable sites of the DW increased with the increase of lignin removal, and the situation of the PMMA/DW composites was just the opposite. In addition, after delignification, the dissolved water content and hydrated water content of the DW increased, and the increase was related to the delignification strength. The increase of dissolved water content indicates that the removal of lignin promotes the production of more volume in the cell wall, which provides space for the adsorption of multilayer water. After MMA in situ polymerization, the hydration and dissolved water content of the PMMA/DW decreased significantly, and the dissolved water content decreased even more significantly. The fitting curves of the H-H model and GDW model for the experimental data points of the differently treated samples were similar. The removal of lignin led to the increase of the w value, indicating that the ratio of water molecules adsorbed in the first layer of DW to the second layer increased, and the removal of lignin resulted in the enhancement of wood hygroscopicity; the opposite was true for the PMMA/DW.

Thermal, Crystallization, and Dynamic Rheological Behavior of Wood Particle/hdpe Composites: Effect of Removal of Wood Cell Wall Composition

Wood‐thermoplastic Composites from Wood Flour and High‐density Polyethylene

Isothermal Crystallization Kinetics of Highly Filled Wood Plastic Composites: Effect of Wood Particles Content and Compatibilizer

Thermal, Mechanical and Morphological Behavior of Poly(propylene)/Wood Flour Composites

High‐performance wood‐reinforced crosslinked high‐density polyethylene composites

Effect of Interfacial Modifiers and Wood Flour Treatment on the Rheological Properties of Recycled Polyethylene/wood Flour Composites

High‐Strength, Thermally Stable, and Processable Wood Fiber/Polyamide Composites for Engineering Structural Components

Morphology, Mechanical Properties and Dimensional Stability of Biomass Particles/High Density Polyethylene Composites: Effect of Species and Composition

Effect of wood flour and compatibilizer content on the properties of wood-plastic composites

Characteristics of paper mill sludge-wood fiber-high-density polyethylene composites

The effect of wood extractives on the thermal stability of different wood-LLDPE composites

Glass fiber/wood flour modified high density polyethylene composites

High density polyethylene/wood flour composite: Optimization of processing temperature, processing time and coupling agent concentration

Effect of Interfacial Modifiers on Physical Properties and Flammability Properties of Pe/Wood Composites

Thermal Properties of Wood-Plastic Composites with Different Compositions

Effect of Fiber Loading on Thermal Properties of Cellulosic Washingtonia Reinforced HDPE Biocomposites

Effects of Wood Content and Modification on Properties of Wood Flour/Polybutylene Adipate Terephthalate Biocomposites

STUDY ON PROPERTIES OF HIGH DENSITY POLYETHYLENE/WOOD FLOUR COMPOSITES

Optimizing the rheological and mechanical properties of ultra-highly filled wood fiber/polyethylene composites through binary alloy matrix strategy

The Effects of Coupling/grafting Modification of Wood Fiber on the Dimensional Stability, Mechanical and Thermal Properties of High Density Polyethylene/wood Fiber Composites

Effect of Lignin Removal on the Hygroscopicity of PMMA/Wood Composites