Abstract:Surface preparation of ultra-high modulus fiber composites for adhesive bonding is challenging due to the subsurface damages that can occur during a standard abrasion operation that could weaken the laminate cohesion. Therefore, it is highly desirable to utilize a non-contact method that can clean and activate the composite surface without exerting an external force to eliminate potential damage. This investigation focuses on the use of atmospheric plasma treatment (APT) for the surface preparation of unidirectional ultra-high modulus, composites for adhesive bonding. The laminates were manufactured using Mitsubishi K13C2U pitch-based carbon fiber with Tencate's RS-3C cyanate-ester resin and bonded with Henkel 9394 epoxy. Surface analysis of plasma-treated samples revealed a significant reduction of surface contamination and increased chemical modification of the matrix material resulting in improved wetting and the formation of chemical groups conducive to bonding. The plasma treatment also produced a minor increase in surface roughening, well below levels expected to contribute to mechanical interlocking. APT epoxy-bonded lap-shear specimens (LSS) exhibited a 50% increase in strength as compared to mechanically abraded samples. It was also shown that solvent rinsing after APT removed a highly-oxidized, poorly bonded carbonate component from the treated resin surface as evidenced by XPS. This surface ash is observed at fairly high concentrations after APT of cyanate ester resin composites limiting functional group contributions. The removal of this ash resulted in increases in LSS of 25% as compared to unrinsed APT surfaces. Lap shear strengths and GIC delamination resistance tests showed improvements over abrasion surface treated samples. Image analysis of the fracture faces for both surface treatments showed that abrasion treated surfaces resulted in sub-surface damage to the fibers that translated into brittle fracture through weak, highly aligned layers within these graphitic fibers. On the other hand, plasma treatment was successfully applied to minimize subsurface damage and resulted in crack propagation along with the more tortuous fiber-matrix interface. The degree of the improvements was ultimately limited by the interlaminar strength of these composites.

Effect of Calcium Chloride on the Surface Properties of Kevlar Fiber

Study on modification of carbon fiber and performance of carbon paper as gas diffusion layer

Kenaf Fiber/poly(ε‐caprolactone) Biocomposite with Enhanced Crystallization Rate and Mechanical Properties

Effect of Irradiation Grafting Epoxy on Surface Characteristics of Carbon Fibers and Mechanical Properties of Composites

Effects of carbon fibers modification on the properties of unsaturated polyester self-healing composites

The Mechanical and NIR Studies on Ultrafine Calcium Carbonate Treated by Four Surface Modifiers.

Effects of CaCl2 and Dopamine Treatment on Surface Structure and Properties of Aramid Fiber

Surface modification of Kevlar fibre fabric and its influence on the properties of Kevlar/epoxy composites

Chemical treatment effect on hydration and mechanical properties of basalt and Kevlar fiber-epoxy-based hybrid composites

Surface Treatment and Dipping Procrss of Kevlar Fiber

Effect of surface functionalization on the surface and inter-facial properties of thermoplastic-coated carbon fibers

Influence of Carbon Nanotube Coatings on Carbon Fiber by Ultrasonically Assisted Electrophoretic Deposition on Its Composite Interfacial Property.

Influence of fiber surface treatments and hybridization on interply and intraply Kevlar reinforced polymer composites

Enhancing the Mechanical properties of CF-Reinforced Epoxy Composites through Chemically Surface Modification of Carbon Fibers via Novel Two-Step Approach by Addition of Epichlorohydrin

Effects of acid modification on coupling agent amount of basalt fiber surface and mechanical property of BF/epoxy composites

Influence of surface modification of carbon fiber based on magnetron sputtering technology on mechanical properties of carbon fiber composites

The surface modification of carbon fiber for thermoplastic HDPE composites

Chemical Modification And Surface Reactions On Carbon Fibers Studied By Sers

Improved mechanical properties of carbon fiber/epoxy composites via fiber surface grafting of rigid-flexible chain structure

Investigations on the effect of plasma treatment on the adhesive bonding behavior of ultra high modulus K13C2U/cyanate ester fiber composites

Effect of Electrochemical Aryl Diazonium Salt Modification on Interfacial Properties of CF/PEEK Composites