Abstract:Silicone rubber (SR) has excellent resistance to high temperatures, and carbon fiber (CF) is a commonly reinforced material. However, the application of carbon fiber in SR composites is limited by the large difference in modulus between the two materials. In order to improve the interfacial bonding of the composites and to exert the reinforcement of carbon fibers, a modulus transition interface, a "flexible-rigid" structure was constructed between CF and SR by coating polydopamine-polyethyleneimine@silica (PDA-PEI@SiO 2 ) on the carbon fiber surface. The results show that the "flexible-rigid" structure of the PDA-PEI@SiO 2 layer not only enhanced the mechanical properties but also improved the thermal resistance and wave-transmission properties of the CF/SR composites. Surface microscopy and structural analysis showed that the "flexible-rigid" structure was successfully coated on the fiber surface, and significantly improved the roughness of the fiber surface. It provided the mechanical meshing between the fiber and matrix when the CF/SR composites were subjected to the tensile loads. The tensile strength and elongation of the SR composite with CF-A-E@8SiO 2 were 37.16 % and 27.46 % higher than that with unmodified CF, respectively. The electrical test showed that the "flexible-rigid" structure could reduce the dielectric constant and dielectric loss of CF/SR composites, thereby improving the wave-transmission properties. Further mechanism analysis of the interfacial bonding showed that abundant hydrogen bonds in the "flexible-rigid" structure at the interface promoted stress dissipation and avoided stress concentration. Meanwhile, the formation of Si-O-Si with high bonding energy also protected the interface from destruction. The thermogravimetric analysis (TGA) found that the introduction of Si-O-Si bonds could significantly improve the thermal resistance of the CF/SR composites at 350 °C for 2 h. It provides guidance for the improvement of the interface bonding in the fiber/rubber composite as well as its functionality.

Improved mechanical properties of carbon fiber/epoxy composites via fiber surface grafting of rigid-flexible chain structure

Simultaneously improving interfacial adhesion and toughness of carbon fiber reinforced epoxy composites by grafting polyethyleneimine on the carbon fiber surface to construct a rigid‐flexible interface

Polydopamine and polyethyleneimine comodified carbon fibers/epoxy composites with gradual and alternate rigid‐flexible structures: Design, characterizations, interfacial, and mechanical properties

Interfacial enhancement of carbon fiber composites by poly(amido amine) functionalization

Enhanced interfacial properties of hierarchical MXene/CF composites via low content electrophoretic deposition

Enhancing the interfacial strength of carbon fiber/epoxy composites by introducing “rigid-flexible” structure onto carbon fiber surface via π–π interaction

Construction of dendritic polymers on carbon fiber surfaces to improve the interfacial bonding of carbon fiber/silicone rubber composites

Influence of Carbon Nanotube Coatings on Carbon Fiber by Ultrasonically Assisted Electrophoretic Deposition on Its Composite Interfacial Property.

Unravelling the Influence of Surface Modification on the Ultimate Performance of Carbon Fiber/Epoxy Composites

Interfacial Enhancement by CNTs Grafting towards High-Performance Mechanical Properties of Carbon Fiber-Reinforced Epoxy Composites

Effect of surface functionalization on the surface and inter-facial properties of thermoplastic-coated carbon fibers

Improving the interfacial property of carbon fiber/PI resin composite by grafting modification of carbon fiber surface

Mussel-tailored carbon fiber/carbon nanotubes interface for elevated interfacial properties of carbon fiber/epoxy composites

Interfacial enhancement by constructing a "flexible-rigid" structure between high-modulus fillers and low-modulus matrix in carbon fiber/silicone rubber composites

Constructing a Double Alternant “Rigid-Flexible” Structure for Simultaneously Strengthening and Toughening the Interface of Carbon Fiber/Epoxy Composites

An organic-inorganic interface structure for CFRP and the enhancement of mechanical properties at room/high temperature

Improving mechanical and thermal properties of short carbon fiber/polyamide 6 composites through a polydopamine/nano‐silica interface layer

Surface Modification of Carbon Fibers by Grafting PEEK-NH2 for Improving Interfacial Adhesion with Polyetheretherketone

Constructing a Superior Interfacial Microstructure on Carbon Fiber for High Interfacial and Mechanical Properties of Epoxy Composites

Co-depositing bio-inspired tannic acid-aminopropyltriethoxysilane coating onto carbon fiber for excellent interfacial adhesion of epoxy composites

Modification of duel functioning PDA-PAADA capsules on interface and resin towards CFRPs with high strength and toughness