Abstract:Emerging organic solar cells based on a ternary strategy is one of the most effective methods for improving the blend film morphology, absorption ability, and device performances. On the other hand, this strategy has had very limited success in all-polymer solar cells (all-PSCs) because of the scarcity of new polymers and the challenges faced during third component optimization. Herein, highly efficient ternary all-PSCs were developed from siloxane-functionalized side chains with a wide-band-gap (Eg) polymer, Si-BDT, which is blended with a medium and ultra-narrow Eg polymer donor and acceptor, PTB7-Th, and DCNBT-TPIC. An impressive power conversion efficiency (PCE) of 13.45% was achieved in the ternary all-PSCs [PTB7-Th(0.6):Si-BDT(0.4):DCNBT-TPIC(0.6)] with the addition of 0.4 wt equivalent Si-BDT into binary all-PSCs [PTB7-Th(1):DCNBT-TPIC(0.6) PCE of 10.11%]. In contrast, the binary all-PSCs with a Si-BDT(1):DCNBT-TPIC(0.6) active layer only exhibited a good PCE of 9.92%. More importantly, the siloxane-functionalized side chains increase the light-absorption ability, carrier mobility, blend miscibility, and film morphology in ternary devices compared to those of the binary devices. Hence, exciton dissociation, charge carrier transport, and suppressed recombination properties were facilitated. In the presence of Si-BDT, both binary and ternary all-PSCs PCEs are significantly improved. Indeed, 13.45% PCE is one of the best values reported for all-PSCs except for those based on polymerized small molecule acceptors. In addition, the ternary all-PSCs showed excellent environmental and thermal stabilities with 95 and 84% of the initial PCE retained after 900 and 500 h, respectively. These results offer effective device engineering, providing a new avenue for improving the device performance in ternary all-PSCs.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c20542.Additional text describing experimental details (materials and measurements and characterization of the all-PSCs), SCLC, UV–vis absorption spectra, UPS analysis, efficiency histograms, J–V curves, PL spectra, EDS element mapping, contact angle, GIXRD study, and recent publications based on ternary all-PSCs (PDF)This article has not yet been cited by other publications.

High Efficient Ternary Polymer Solar Cells Based on Absorption Complementary Materials As Electron Donor

Ternary Nonfullerene Polymer Solar Cells with a Power Conversion Efficiency of 11.6% by Inheriting the Advantages of Binary Cells

Ternary Polymer Solar Cells Based-on Two Polymer Donors with Similar HOMO Levels and an Organic Acceptor with Absorption Extending to 850 Nm

High-Performance Ternary Nonfullerene Polymer Solar Cells with Both Improved Photon Harvesting and Device Stability.

Ternary nonfullerene polymer solar cells with efficiency >13.7% by integrating the advantages of the materials and two binary cells

Ternary Polymer Solar Cells with High Efficiency of 14.24% by Integrating Two Well‐Complementary Nonfullerene Acceptors

Ternary Polymer Solar Cells Achieving 11.78% Efficiency with Two Fluorinated Non-Fullerene Acceptors

Ternary Polymer Solar Cells with Low-Cost P3HT as the Second Donor by the Complementary Absorption Region from Long-Wavelength to Medium-Wavelength Regions Forming Cascaded HOMO and LUMO Energy Levels

Enhanced Photovoltaic Performances Via Ternary Blend Strategy Employing a Medium-Bandgap D-A Type Alternating Copolymer As the Single Donor

Ternary Polymer Solar Cells Enabled Using Two Donor Polymers with Broad Absorption and Cascade LUMO Levels

Achieving over 11% Power Conversion Efficiency in PffBT4T-2OD-based Ternary Polymer Solar Cells with Enhanced Open-Circuit-voltage and Suppressed Charge Recombination

Realization of Performance Enhancement in Ternary Polymer Solar Cells by Broad Absorption, Efficient Energy Transfer, and Balanced Charge Carrier Mobility

Ternary All-Polymer Solar Cells with 8.5% Power Conversion Efficiency and Excellent Thermal Stability.

A Minimal Benzo[c][1,2,5]thiadiazole-Based Electron Acceptor As a Third Component Material for Ternary Polymer Solar Cells with Efficiencies Exceeding 16.0%

9.0% Power Conversion Efficiency from Ternary All-Polymer Solar Cells

Highly Efficient Ternary All‐Polymer Solar Cells with Enhanced Stability

Facile Strategy for Third Component Optimization in Wide-Band-Gap π-Conjugated Polymer Donor-Based Efficient Ternary All-Polymer Solar Cells

High Voc Ternary Nonfullerene Polymer Solar Cells with Improved Efficiency and Good Thermal Stability

Ternary Strategy Enables Non‐Halogenated Solvent‐Processed All‐Polymer Solar Cells with High Efficiency Over 18%

Ternary Solar Cells Via Ternary Polymer Donors and Third Component PC71BM to Optimize Morphology with 13.15% Efficiency

Ternary All-Polymer Solar Cells with Two Synergetic Donors Enable Efficiency over 14.5%