Abstract:Internal metallurgical defects and poor mechanical properties and surface quality of the formed parts are the most important challenges of metal micro-droplets deposition manufacturing technology. Lack of strong coalescence between neighboring droplets and the blocking effects of periodic ripples on the fusion process are major sources of abovementioned problems. To address this issue, a tungsten inert gas (TIG) welding arc was introduced to pre-melt the material below the droplet impacting location, thus, one droplet train will be deposited on a curved molten pool surface to fabricate deposited layers in an additive approach. In the present work, a numerical model based on the computational fluid dynamics (CFD) method was developed to investigate the dynamic behaviors of successive droplets' impact and coalescence on the molten pool created by a tilted TIG welding arc, and focuses on the effect of the offset distance between the impacting point of droplet and the longitudinal plane of molten pool on the deposition morphology and the impact-induced molten pool behaviors. The simulated tracks exhibit regular scaly shapes at different offset distances, which is validated against the corresponding experiments. The results indicated that as the lateral offset distance increases, the symmetric spreading and recoiling of the subsequent droplets on the pre-existing bead will be broken due to the inclined and curved solidification front morphologies, the inclined front morphologies are caused by the increased growth rate of the solidification front at the impact zone. With an increased lateral offset distance, the volume of the molten pool decreases, the width of the rear molten pool increases slightly. The calculated solidification parameters are found to be dependent of the offset distance, and vary significantly at the onset of solidification at different portions of the molten pool. The scientific findings provide useful insights for further researches of TIGassisted DDM.

Investigation of Droplet Transfer Behaviours in Cold Metal Transfer (CMT) Process on Welding Ti-6Al-4V Alloy

Metal transfer behavior during CMT-based Wire Arc Additive Manufacturing of Ti-6Al-4V alloy

Arc characteristics and droplet transfer process in CMT welding with a magnetic field

The Cmt Short-Circuiting Metal Transfer Process and Its Use in Thin Aluminium Sheets Welding

The arc characteristics and metal transfer behaviour of cold metal transfer and its use in joining aluminium to zinc-coated steel

Effect of droplet transition on arc morphology, Mn evaporation and microstructure during the CMT welding with high nitrogen Cr-Mn steel

Short Circuiting Transfer, Formation, and Microstructure of Ti-6Al-4V Alloy by External Longitudinal Magnetic Field Hybrid Metal Inert Gas Welding Additive Manufacturing

Metal transfer electrical characteristics and its analysis in pulsed current gas metal arc welding

Solidification Cracking Restraining Mechanism of Al-Cu-Mg-Zn Alloy Welds Using Cold Metal Transfer Technique

Characteristics of Torch-Offset Cold Metal Transition-Cycle Step Welding of 5052Al Alloy with T2 Copper via Al-12Si Filler

Metal Transfer Behavior and Molten Pool Dynamics in Cold Metal Transfer Pulse Advanced Additive Manufacturing of 7075 Aluminum Alloy

An Initial Study on Welding Procedure Using Tandem MIG Welding of High Strength Aluminum Alloy

Influence of the Laser Thermal Effect on the Droplet Transfer Behavior in Laser-Cmt Welding

Interfacial phenomena of cold metal transfer (CMT) welding of zinc coated steel and wrought aluminium

Investigation on the mass transfer control, process stability and welding quality during underwater pulse current FCAW for Q235

Characteristics of droplet transfer, molten pool formation, and weld bead formation of oscillating laser hot-wire tungsten inert gas hybrid welding

Study on appearance and mechanical behavior of additively manufacturing of Ti–6Al–4V alloy by using cold metal transfer

Fluid Thermodynamic Simulation of Ti-6Al-4V Alloy in Laser Wire Deposition

Study on Metal Transfer of MIG/MAG

Fundamental investigation into mass transfer process and microstructural transformation pathways in Ti-6Al-4V via underwater wire-laser directed energy deposition

Offset impacting of a liquid aluminum droplet train on a molten pool on a horizontally moving substrate during TIG-assisted droplet deposition manufacturing