ChemInform Abstract: One Step Preparation of a High Performance Ge—C Nanocomposite Anode for Lithium Ion Batteries by Tandem Plasma Reactions.

Wei Li,Jie Zheng,Tiankai Chen,Teng Wang,Xiaojuan Wang,Xingguo Li

DOI: https://doi.org/10.1002/chin.201415011

2014-01-01

ChemInform

Abstract:AbstractUltrafine Ge nanoparticles embedded in a carbon matrix are prepared in a tandem plasma reactor.

What problem does this paper attempt to address?

One step preparation of a high performance Ge-C nanocomposite anode for lithium ion batteries by tandem plasma reactions.

Wei Li,Jie Zheng,Tiankai Chen,Teng Wang,Xiaojuan Wang,Xingguo Li

DOI: https://doi.org/10.1039/c3cc47719c

IF: 4.9

2014-01-01

Chemical Communications

Abstract:We employ a tandem plasma reaction method to prepare ultrafine Ge nanoparticles embedded in a carbon matrix in one step. The obtained Ge-C composite exhibits very high lithium storage capacity (980 mA h g(-1)) and excellent cycling performance (less than 2% capacity loss in 100 cycles).
Facile Scalable Synthesis Of Carbon-Coated Ge@C And Gex@C (X=S, Se) Anodes For High Performance Lithium-Ion Batteries

Miao Wang,Hui Zheng,Wenqi Zhan,Qinxin Luo,Kaibin Tang

DOI: https://doi.org/10.1002/slct.201901408

2019-01-01

ChemistrySelect

Abstract:Amorphous germanium@C and germanium chalcogenides@C composites have been fabricated via a simply developed synthetic route. Taking advantage of the carbon coating of these materials, they all exhibit excellent Li storage properties as anode materials for lithium ion batteries (LIBs). Typically, Ge@C presents a capacity of 672 mAh g(-1) after 80 cycles at current density of 0.5 A g(-1). The capacities of GeS@C are about 604 mAh g(-1) over 180 cycles at 0.2 A g(-1) and 365 mAh g(-1) at 0.5 A g(-1) after 1000 cycles, respectively. As for GeSe@C electrode, it exhibit high capacities of nearly 780 mAh g(-1) at 0.2 A g(-1) over 180 cycles and 562 mAh g(-1) at 0.5 A g(-1) over 60 cycles.
Ge@C Three-Dimensional Porous Particles As High-Performance Anode Materials of Lithium-Ion Batteries

Chengmao Xiao,Ning Du,Yifan Chen,Jingxue Yu,Wenjia Zhao,Deren Yang

DOI: https://doi.org/10.1039/c5ra08656f

IF: 4.036

2015-01-01

RSC Advances

Abstract:We demonstrate the synthesis of Ge@C three-dimensional porous particles (Ge@C TPP) via the decomposition of magnesium germanide (Mg2Ge) and subsequent deposition of a carbon layer.
Controllable preparation of carbon coating Ge nanospheres with a cubic hollow structure for high-performance lithium ion batteries

Ying Zhao,Yilin Li,Tingyu Wang,Xudong Zhao,Xianglong Kong,Gaofu Li,Zicong Wang,Fei He,Xinghua Chang,Zhiliang Liu,Linzhi Wu,Milin Zhang,Piaoping Yang

DOI: https://doi.org/10.1016/j.jcis.2024.08.006

2024-08-03

Abstract:Germanium based nanomaterials are very promising as the anodes for the lithium ion batteries since their large specific capacity, excellent lithium diffusivity and high conductivity. However, their controllable preparation is still very difficult to achieve. Herein, we facilely prepare a unique carbon coating Ge nanospheres with a cubic hollow structure (Ge@C) via a hydrothermal synthesis and subsequent pyrolysis using low-cost GeO2 as precursors. The hollow Ge@C nanostructure not only provides abundant interior space to alleviate the huge volumetric expansion of Ge upon lithiation, but also facilitates the transmission of lithium ions and electrons. Moreover, experiment analyses and density functional theory (DFT) calculations unveil the excellent lithium adsorption ability, high exchange current density, low activation energy for lithium diffusion of the hollow Ge@C electrode, thus exhibiting significant lithium storage advantages with a large charge capacity (1483 mAh/g under 200 mA g-1), distinguished rate ability (710 mAh/g under 8000 mA g-1) as well as long-term cycling stability (1130 mAh/g after 900 cycles under 1000 mA g-1). Therefore, this work offers new paths for controllable synthesis and fabrication of high-performance Ge based lithium storage nanomaterials.
Facile One-Pot Method Synthesis Cnt-Geo2 Nanocomposite For High Performance Li Ion Battery Anode Material

Fangfang Jia,Lingxiao Song,Wei Wei,Peng Qu,Maotian Xu

DOI: https://doi.org/10.1039/c4nj01742k

IF: 3.3

2015-01-01

New Journal of Chemistry

Abstract:For the first time, we synthesized a carbon nanotubes-GeO2 nanocomposite via a facile one-pot solution method. The as-prepared carbon nanotubes-GeO2 nanocomposite appears as webs of curved nanotubes and nanoparticles, forming strong intertwined entanglements with a three-dimensional (3D) network structure. Such a hybrid structure can not only greatly improve the electron conductivity of the nanocomposite, but also effectively buffer the volume change of GeO2 during the charge-discharge process. The carbon nanotubes-GeO2 nanocomposite retains 813.7 mA h g(-1) even after 500 cycles at the current rate of 0.2 A g(-1) as an electrode material for Li ion batteries (LIBs) and shows high rate capability at variable current rates.
Nanocomposites As Anode for Lithium-Ion Battery

Xiangcheng Sun,Manu Hegde,Yuefei Zhang,Min He,Lin Gu,Yongqing Wang,Jie Shu,Pavle V. Radovanovic,Bo Cui

DOI: https://doi.org/10.1016/s1452-3981(23)07875-6

IF: 1.541

2014-01-01

International Journal of Electrochemical Science

Abstract:Nanocomposite particles of amorphous carbon-Li4Ti5O12 (C-LTO) and carbon nanotube-Li4Ti5O12 (CNT-LTO) were synthesized by solvothermal method and subsequent high-temperature calcination. X-ray diffraction (XRD), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HR-TEM), and selected area electron diffraction (SAED) were applied to characterize the phase structure, particle morphology, and the coating structure. XRD analysis, TEM micrographs, HR-TEM images and SAED analysis revealed that both LTO particles exhibited a well- developed spinel nanocrystal structure with average sizes between 20-70 nm. The C-LTO particles exhibited roughly spherical shape coated by an amorphous carbon layer up to 10 nm in thickness. The CNT-LTO samples showed uniform square nanocrystals with edge length around 20 nm and nanoscale graphitic layers covering the surface, revealing the carbon nanotubes interconnection networks among the particle assemblies. Electrochemical studies of lithium insertion/extraction performance are evaluated by the galvanostatic charge/discharge tests, cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Both LTO particles showed the superior initial discharge capacity of more than 200 mAh/g at 1/10C rate. The irreversible capacity of the C-LTO particles at more cycles was due to large polarization resulted from excessive carbon and possible residual precursors. The CNT-LTO particles show larger reversible capacity and enhanced electrochemical Li+ insertion/extraction kinetics at different cycling rates. The comparative structural and electrochemical analyses demonstrated that both nanoscale graphitic covering layers and the CNT interconnection networks increase the electronic conductivity and improve the kinetics rates of lithium insertion/extraction in the CNT-LTO particles.
Zn2geo4@C Core-Shell Nanorods As Highly Reversible Anode Materials for Lithium-Ion Batteries

Yifan Chen,Yangfan Lin,Ning Du,Chengmao Xiao,Shali Wu,Yaguang Zhang,Deren Yang

DOI: https://doi.org/10.1002/ente.201700058

IF: 4.149

2017-01-01

Energy Technology

Abstract:We report the synthesis of Zn2GeO4 nanorods using a simple hydrothermal process. After the coating of a carbon layer by the thermal decomposition of acetylene gas, the Zn2GeO4@C core-shell nanorods were obtained. The as-synthesized Zn2GeO4@C core-shell nanorods were used as anode materials of lithium-ion batteries, which showed good cycling and rate performance. A highly reversible specific capacity of 718 mAhg(-1) after 400 cycles was achieved at a current density of 400 mAg(-1). The core-shell nanostructures and partially amorphous and porous nanostructures helped to alleviate the volume change and enhance the conductivity during the charge/discharge process, which may be responsible for the good performance.
Facile Synthesis of Ge/C Nanocomposite As Superior Battery Anode Material

Wei Guo,Lin Mei,Qingqin Feng,Jianmin Ma

DOI: https://doi.org/10.1016/j.matchemphys.2015.11.016

IF: 4.778

2015-01-01

Materials Chemistry and Physics

Abstract:Germanium (Ge) is a high capacity anode material for lithium-ion batteries (LIBs), but still suffers from poor cyclability and stability due to the huge volume change during lithium-ion intake/remove process. In this work, we present a synthetic method for preparing Ge/C nanocomposite through annealing the precursors GeO2 and polyvinylpyrrolidone (PVP) in Ar/H-2 atmospheres. The as-synthesized Ge/C nanocomposite delivers a reversible specific capacity of 530 mAh/g after 100 cycles at a current density of 200 mA/g, and a high rate capability due to its composite structure. The excellent electrochemical performance can be attributed to the carbon layers structure, which not only provides the room for accommodation of volume expansion, but also enhances the electronic conductivity of the electrode. Such Ge/C nanocomposite are promising as a potential anode material for LIBs. (C) 2015 Elsevier B.V. All rights reserved.
Easy Preparation of Nanoporous Ge/Cu3Ge Composite and Its High Performances Towards Lithium Storage

Qin Hao,Qiang Liu,Yuanyuan Zhang,Caixia Xu,Jiagang Hou

DOI: https://doi.org/10.1016/j.jcis.2018.12.104

IF: 9.9

2019-01-01

Journal of Colloid and Interface Science

Abstract:Nanoporous Ge/Cu3Ge composite is fabricated simply through selective dealloying of GeCuAl precursor alloy in dilute alkaline solution. The as-made Ge/Cu3Ge is characterized by three dimensional (3D) bicontinuous network nanostructure which comprises of substantial nanoscale pore voids and ligaments. Owing to the 3D porous architecture and the introduction of well-conductive Cu3Ge, the lithium storage performances of Ge are dramatically enhanced in terms of higher cycling stability and superior rate performance. Nanoporous Ge/Cu3Ge anode delivers steady capacities above 1000 mA h g(-1) upon cycling for 70 loops at 400 mA g(-1). In particular, after 300 cycles at the high rate of 3200 mA g(-1) the capacity retention for Ge/Cu3Ge is able to reach a maximum of 99.3%. On the contrary, the pure nanoporous Ge encounters severe capacity decay. In view of the outstanding energy storage performances and easy preparation, nanoporous Ge/Cu3Ge exhibits great application potential as an advanced anode in lithium storage related technologies. (C) 2018 Elsevier Inc. All rights reserved.
Triblock Polymer/Acetylene Black Dual‐Assisted Preparation of Ge/C Nanocomposites with Superior Lithium Storage Performance

Mingming Zhang,Kuan Shen,Mingyue Gao,Xingmei Guo,Junhao Zhang,Hongxing Gu,Qinghong Kong,Zhong Jin

DOI: https://doi.org/10.1002/batt.202400139

2024-04-09

Batteries & Supercaps

Abstract:Anode materials based on IV main group elements like Si, Ge, and Sn show great potential for lithium‐ion batteries (LIBs) due to their high specific capacity and low working potential. However, issues such as volume expansion and lattice pulverization hinder their practical usage. To address these issues for Ge, a novel F127 triblock polymer/acetylene black dual‐assisted strategy is proposed to achieve uniform dispersion of polycrystalline Ge, enabling the preparation of Ge@C nanocomposites via hydrogen reduction. The introduced F127 triblock polymer and acetylene black serves a dual purpose to enhance electrical conductivity and prevent Ge nanoparticles from agglomeration. When tested as anode material for LIBs, the Ge@C nanocomposites exhibit exceptional electrochemical performances, demonstrating a sustained specific discharge capacity of 780 mA h g‐1 at 0.2 A g‐1 after 100 cycles. Moreover, the capacity remains at 767 mA h g‐1 even after 300 cycles at a higher current density of 0.5 A g‐1. These enhanced lithium storage performances are attributed to the combined effects of well‐dispersed tiny Ge nanoparticles, uniform carbon coating, and an abundance of defects. These factors effectively mitigate the volume expansion and lattice pulverization of Ge nanoparticles and concurrently enhance their conductivity, leading to improved overall performance in LIBs.

materials science, multidisciplinary,electrochemistry
In Situ One-Step Synthesis of a Ge/Zn2GeO4/N-Doped Carbon Composite As an Anode Material for Lithium-Ion Batteries

Zhuo Wang,Xiaoli Dong,Bin Zhao,Yonggang Wang,Yongyao Xia

DOI: https://doi.org/10.1021/acssuschemeng.3c02547

IF: 8.4

2023-01-01

ACS Sustainable Chemistry & Engineering

Abstract:Zinc orthogermanate (Zn2GeO4) is an attractive anode material for lithium-ion rechargeable batteries. Nevertheless, owing to its disadvantages of low electrical conductivity and large volume change in cycles, it is subjected to poor cycling stability and rate capability, which restrict its rapid development. Herein, an in situ one-step synthetic route is presented for preparing Ge/Zn2GeO4/N-doped carbon composite by direct carbonization of a mixture of Zn-based metal-organic framework (MET-6) and commercial GeO2 under N-2 atmosphere. The composite prepared at 800 ? exhibits a uniform spherical morphology comprising Ge/Zn2GeO4 crystals that are tightly covered by thin layers of nitrogen-doped carbon. The Ge/Zn2GeO4/N-doped carbon anode displays a large charge capacity of 901.9 mAh g(-1) over 100 cycles at 0.1 A g(-1), long-term stability over 1000 cycles at 1.0 A g(-1), as well as good rate capability. Additionally, the assembled full cell with a LiNi0.8Co0.1Mn0.1O2 cathode and Ge/Zn2GeO4/N-doped carbon composite anode also shows good electrochemical performance.
Cu3Ge/Ge@C Nanocomposites Crosslinked by the in Situ Formed Carbon Nanotubes for High-Rate Lithium Storage

Xianyu Liu,Ning Lin,Kangli Xu,Ying Han,Yue Lu,Yingyue Zhao,Jianbin Zhou,Zheng Yi,Changhe Cao,Yitai Qian

DOI: https://doi.org/10.1016/j.cej.2018.07.015

IF: 15.1

2018-01-01

Chemical Engineering Journal

Abstract:In a convenient and uncomplicated way, Cu3Ge/Ge@C nanocomposites crosslinked by the in situ formed carbon nanotubes (CNTs-Cu3Ge/Ge@C) is reported. In this method, carbon nanotubes are produced in situ to crosslink Cu3Ge/Ge@C nanocomposites by the catalysis action of nascent Cu* under an acetylene atmosphere at 500 degrees C, in which the nascent Cu* is created by the reaction between CuCl and Ge particles, Cu3Ge is then synchronously formed by the Ge and Cu*. Investigated as the anode materials for lithium ion batteries, a high capacity retention of 1013.4 mA h g(-1) is exhibited by the prepared CNTs-Cu3Ge/Ge@C at 0.5C after 1000 cycles and a high rate capacity of 931.7 mA h g(-1) at 10C in Li-Ge half cells.
Ionic Liquid Electrodeposition of Germanium/carbon Nanotube Composite Anode Material for Lithium Ion Batteries

Jian Hao,Na Li,Xiaoxuan Ma,Xiaoxu Liu,Xusong Liu,Yao Li,Hongbo Xu,Jiupeng Zhao

DOI: https://doi.org/10.1016/j.matlet.2015.01.022

IF: 3

2015-01-01

Materials Letters

Abstract:Germanium nanoparticles (Ge-NPs) are combined with carbon nanotubes (CNTs) to fabricate anodes for Li-ion batteries through the electrodeposition of Ge from ionic liquids on the surface of the CNTs. The latter are electrophoretically deposited on a copper collector at room temperature without any binders, with a good electrical contact achieved nonetheless between the active material and the collector. In the composite, the CNTs readily accommodate the large volume changes of the Ge particles during cycling. The composite exhibits better reversible lithiation–delithiation behavior, an improved rate performance, and also has better electrochemical properties than Ge-NPs. The nanocomposite anode developed here delivers a reversible capacity of 810mAh/g after 100 cycles at 0.2C.
ChemInform Abstract: Honeycomb-Like Macro-Germanium As High-Capacity Anodes for Lithium-Ion Batteries with Good Cycling and Rate Performance.

Jianwen Liang,Xiaona Li,Zhiguo Hou,Tianwen Zhang,Yongchun Zhu,Xuedong Yan,Yitai Qian

DOI: https://doi.org/10.1002/chin.201531014

2015-01-01

ChemInform

Abstract:Macroporous Ge powder is prepared by reduction of commercial GeO 2 with Mg under hydrothermal conditions (autoclave, 200 °C, 5 h).
A synchronous approach for facile production of Ge-carbon hybrid nanoparticles for high-performance lithium batteries.

Xiaona Li,Jianwen Liang,Zhiguo Hou,Yongchun Zhu,Yan Wang,Yitai Qian

DOI: https://doi.org/10.1039/c5cc00080g

IF: 4.9

2015-01-01

Chemical Communications

Abstract:A novel approach via reduction and carbonization of germanium chelate synchronously to in situ formed uniform Ge-carbon hybrid nanoparticles has been developed. The Ge-carbon composites, derived from the homogenous dispersion of the elements within the chelate complex matrix at the molecular level, exhibit outstanding electrochemical lithium-storage performance with high capacity, excellent rate capability, and ultra long cycling life.
Confining Nano-GeS2 in Cross-Linked Porous Carbon Networks for High-Performance and Flexible Li-Ion Battery Anodes

Dong Feng,Qi Liu,Zhongming Li,Tianbiao Zeng

DOI: https://doi.org/10.1021/acsaem.1c00925

IF: 6.4

2021-01-01

ACS Applied Energy Materials

Abstract:As anode materials for lithium-ion batteries (LiBs), GeS2 has attracted considerable attention owing to its high theoretical capacity. Nevertheless, pulverization of GeS2 during the lithiation/delithiation process impedes its practical applications. Hybrid cross-linking with the second phase material is an effective strategy to improve the charge/discharge cycling performance. Herein, a high-capacity, long cycle-life nano-GeS2/carbon (GeS2/C) composite was facilely synthesized via the solid-state ball milling reaction. GeS2/C was then used to construct the three-dimensional (3D) flexible electrode. In this way, the flexible electrode with nano-GeS2/C particles confining in porous carbon networks exhibited improved reversible capacity and cycling performance, thanks to the unique confinement cellular structure. For instance, the flexible electrode with similar to 500 mu m thickness delivered capacities of similar to 991, similar to 888, similar to 737, and similar to 604 mA h g(-1) at 0.1, 0.2, 0.5, and 1 A g(-1), respectively. Upon stacking into two layers of the GeS2/C flexible electrode, the increased thickness displayed no effects on its diffuse-controlled capacity ratio and Li+ diffusion coefficient. This work provides a new strategy to stabilize germanium chalcogenides for LiB anodes with enhanced performance and sheds light on the preparation of other types of 3D flexible electrodes.
Binder-Free Germanium Nanoparticle decorated Multi-Wall Carbon Nanotube Anodes prepared via two-step Electrophoretic Deposition for high capacity Li-Ion Batteries

Xuan-Manh Pham,Syed Abdul Ahad,Niraj Patil,Hugh Geaney,Shalini Singh,Kevin Michael Ryan

DOI: https://doi.org/10.1039/d3nh00501a

2024-02-14

Nanoscale Horizons

Abstract:Germanium (Ge) has a high theoretical specific capacity (1384 mAh g−1) and fast lithium-ion diffusivity, which makes it an attractive anode material for lithium-ion batteries (LIBs). However, large volume changes during lithiation can lead to poor capacity retention and rate capability. Here, electrophoretic deposition (EPD) is used as a facile strategy to prepare Ge nanoparticle carbon-nanotube (Ge/CNT) electrodes. The Ge and CNT mass ratio in the Ge/CNT nanocomposites is controllable by varying the deposition time, voltage, and concentration of the Ge NPs dispersion in the EPD process. The optimized Ge/CNT nanocomposite exhibited long-term cyclic stability, with a capacity of 819 mA h g−1 after 1000 cycles at C/5 and a reversible capacity of 686 mA h g−1 after 350 cycles (with a minuscule capacity loss of 0.07% per cycle) at 1C. The Ge/CNT nanocomposite electrodes delivered dramatically improved cycling stability compared to control Ge nanoparticles. This can be attributed to the synergistic effects of implanting the Ge into a 3D interconnected CNT network which acts as a buffer layer to accommodate the volume expansion of Ge NPs during lithiation/delithiation, limiting cracking and/or crumbling, to retain the integrity of the Ge/CNT nanocomposite electrodes.

materials science, multidisciplinary,chemistry, physical,nanoscience & nanotechnology
In Situ Confined Co 5 Ge 3 Alloy Nanoparticles in Nitrogen-Doped Carbon Nanotubes for Boosting Lithium Storage

Junxiu Wu,Anwen Tang,Shuping Huang,Junming Li,Lingxing Zeng,Mingdeng Wei

DOI: https://doi.org/10.1021/acsami.0c15942

2020-09-29

Abstract:Ge-based materials have garnered much attention in lithium-ion batteries (LIBs) for their high theoretical capacity, but these materials suffer from huge volume changes and serious pulverization, which cause insufficient lithium storage performance. Herein, a composite composed of Co5Ge3- and nitrogen-doped carbon nanotube (Co5Ge3/N-CNT) was successfully synthesized using ZIF-67 and GeO2 as precursors. There are interactions between the Co5Ge3 alloy nanoparticles and carbon nanotubes in the growth process, in which the Co5Ge3 alloy nanoparticles were confined in situ in N-CNTs and the in situ growth of N-CNTs was boosted in the existence of the Co5Ge3 catalyst. Density functional theory calculations revealed that the electronic conductivity of the Co5Ge3 alloy is much higher than that of Ge and the Li+ interaction energy of the former is lower than that of the latter. In addition, the interconnected carbon nanotubes not only offer Li+ diffusion pathways and electronic networks but also increase electronic conductivity. Importantly, carbon nanotubes and Co metal have a synergistic effect of buffering volume charge of Ge in the process of Li+ intercalation/deintercalation. As expected, the Co5Ge3/N-CNT composite demonstrated a high reversible capacity of 853.7 mA h g–1 at 2 A g–1 after 1500 cycles and attractive rate performance of up to 10 A g–1.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c15942?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c15942</a>.2 × 2 × 2 supercell of Ge; primitive cell of Co5Ge3; 3 × 1 × 1 supercell of Co5Ge3; SEM images of Ge/C, ZIF-67/GeO2, and Co5Ge3/N-CNT; TEM images of ZIF-67/GeO2; EDS spectrum of Co5Ge3 /N-CNT; XRD patterns of ZIF-67/GeO2 and Co5Ge3/N-CNT; XPS spectra of Co5Ge3 /N-CNT; TG curve of Co5Ge3/N-CNT; table of comparison of charge/discharge performance of Ge/C-based anodes for lithium-ion batteries; long-term cycling performance at 2 A g–1 and rate capabilities measured at various current densities from 100 to 3000 mA g–1 for the Ge/C electrode; TEM images of the Co5Ge3/N-CNT electrode after 1500 cycles; ex situ XRD patterns of the Co5Ge3/N-CNT electrode; and EIS spectra of Co5Ge3/N-CNT and the Ge/C electrode (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c15942/suppl_file/am0c15942_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

materials science, multidisciplinary,nanoscience & nanotechnology
Ag Nanoparticles Anchored on Nanoporous Ge Skeleton As High‐Performance Anode for Lithium‐ion Batteries

Ji Zhou,Peng Huang,Qin Hao,Lina Zhang,Hong Liu,Caixia Xu,Jinghua Yu

DOI: https://doi.org/10.1002/cjoc.202100288

IF: 5.56

2021-01-01

Chinese Journal of Chemistry

Abstract:Main observation and conclusionNanoporous (NP) Ge/Ag composite is controllably fabricated via one simple dealloying method under mild conditions. After corroding the well‐designed Ge9Ag1Al90 source alloy, the resulting Ge/Ag consists of the three dimensional (3D) interconnected Ge network skeleton with Ag nanoparticles uniformly dispersed onto the surface. Benefitting from unique 3D porous nanostructure and introduction of high‐conductive Ag, the NP Ge/Ag composite exhibits much enhanced lithium storage performances by comparison with pure Ge material, including higher reversible capacitance, optimized rate capability as well as superior cycling performances. Besides, the NP Ge/Ag holds high cycling stability with large reversible capacity of 500 mA·h·g–1 remained under high current rate of 3200 mA·g–1 for an extended period of 300 loops. The Ge/Ag composite presents great potential in applications as an advanced anode candidate for lithium ion batteries in virtue of its excellent performances and green fabrication.
Confining Nano-GeS 2 in Cross-Linked Porous Carbon Networks for High-Performance and Flexible Li-Ion Battery Anodes

Dong Feng,Qi Liu,Zhongming Li,Tianbiao Zeng

DOI: https://doi.org/10.1021/acsaem.1c00925

IF: 6.4

2021-05-27

ACS Applied Energy Materials

Abstract:As anode materials for lithium-ion batteries (LiBs), GeS2 has attracted considerable attention owing to its high theoretical capacity. Nevertheless, pulverization of GeS2 during the lithiation/delithiation process impedes its practical applications. Hybrid cross-linking with the second phase material is an effective strategy to improve the charge/discharge cycling performance. Herein, a high-capacity, long cycle-life nano-GeS2/carbon (GeS2/C) composite was facilely synthesized via the solid-state ball milling reaction. GeS2/C was then used to construct the three-dimensional (3D) flexible electrode. In this way, the flexible electrode with nano-GeS2/C particles confining in porous carbon networks exhibited improved reversible capacity and cycling performance, thanks to the unique confinement cellular structure. For instance, the flexible electrode with ∼500 μm thickness delivered capacities of ∼991, ∼888, ∼737, and ∼604 mA h g–1 at 0.1, 0.2, 0.5, and 1 A g–1, respectively. Upon stacking into two layers of the GeS2/C flexible electrode, the increased thickness displayed no effects on its diffuse-controlled capacity ratio and Li+ diffusion coefficient. This work provides a new strategy to stabilize germanium chalcogenides for LiB anodes with enhanced performance and sheds light on the preparation of other types of 3D flexible electrodes.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.1c00925?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.1c00925</a>.Additional data analysis including microscopy images, SEM images, rate CV profiles, XRD results, and TG and GITT curves of GeS2-based materials (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.1c00925/suppl_file/ae1c00925_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

materials science, multidisciplinary,chemistry, physical,energy & fuels

ChemInform Abstract: One Step Preparation of a High Performance Ge—C Nanocomposite Anode for Lithium Ion Batteries by Tandem Plasma Reactions.

One step preparation of a high performance Ge-C nanocomposite anode for lithium ion batteries by tandem plasma reactions.

Facile Scalable Synthesis Of Carbon-Coated Ge@C And Gex@C (X=S, Se) Anodes For High Performance Lithium-Ion Batteries

Ge@C Three-Dimensional Porous Particles As High-Performance Anode Materials of Lithium-Ion Batteries

Controllable preparation of carbon coating Ge nanospheres with a cubic hollow structure for high-performance lithium ion batteries

Facile One-Pot Method Synthesis Cnt-Geo2 Nanocomposite For High Performance Li Ion Battery Anode Material

Nanocomposites As Anode for Lithium-Ion Battery

Zn2geo4@C Core-Shell Nanorods As Highly Reversible Anode Materials for Lithium-Ion Batteries

Facile Synthesis of Ge/C Nanocomposite As Superior Battery Anode Material

Easy Preparation of Nanoporous Ge/Cu3Ge Composite and Its High Performances Towards Lithium Storage

Triblock Polymer/Acetylene Black Dual‐Assisted Preparation of Ge/C Nanocomposites with Superior Lithium Storage Performance

In Situ One-Step Synthesis of a Ge/Zn2GeO4/N-Doped Carbon Composite As an Anode Material for Lithium-Ion Batteries

Cu3Ge/Ge@C Nanocomposites Crosslinked by the in Situ Formed Carbon Nanotubes for High-Rate Lithium Storage

Ionic Liquid Electrodeposition of Germanium/carbon Nanotube Composite Anode Material for Lithium Ion Batteries

ChemInform Abstract: Honeycomb-Like Macro-Germanium As High-Capacity Anodes for Lithium-Ion Batteries with Good Cycling and Rate Performance.

A synchronous approach for facile production of Ge-carbon hybrid nanoparticles for high-performance lithium batteries.

Confining Nano-GeS2 in Cross-Linked Porous Carbon Networks for High-Performance and Flexible Li-Ion Battery Anodes

Binder-Free Germanium Nanoparticle decorated Multi-Wall Carbon Nanotube Anodes prepared via two-step Electrophoretic Deposition for high capacity Li-Ion Batteries

In Situ Confined Co 5 Ge 3 Alloy Nanoparticles in Nitrogen-Doped Carbon Nanotubes for Boosting Lithium Storage

Ag Nanoparticles Anchored on Nanoporous Ge Skeleton As High‐Performance Anode for Lithium‐ion Batteries

Confining Nano-GeS 2 in Cross-Linked Porous Carbon Networks for High-Performance and Flexible Li-Ion Battery Anodes